Keysight Technologies E3646A Manuel

Keysight E364xA

Dual Output

DC Power Supplies

User’s and

Service Guide

II E364xA User’s and Service Guide

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Keysight

Technologies as governed by United States

and international copyright laws.

Manual Part Number

E3646-90001

Edition

Edition 11, November 2014

Keysight Technologies

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Warranty

The material contained in this document is

provided “as is,” and is subject to change,

without notice, in future editions. Further,

to the maximum extent permitted by the

applicable law, Keysight disclaims all

warranties, either express or implied, with

regard to this manual and any information

contained herein, including but not limited

to the implied warranties of merchantabil-

ity and fitness for a particular purpose.

Keysight shall not be liable for errors or for

incidental or consequential damages in

connection with the furnishing, use, or

performance of this document or of any

information contained herein. Should Key-

sight and the user have a separate written

agreement with warranty terms covering

the material in this document that conflict

with these terms, the warranty terms in

the separate agreement shall control.

Technology Licenses

The hardware and or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Keysight provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the likes

of that, if not correctly performed

or adhered to, could result in dam-

age to the product or loss of impor-

tant data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the likes of that, if not correctly

performed or adhered to, could

result in personal injury or death.

Do not proceed beyond a WARN-

ING notice until the indicated

conditions are fully understood

and met.

E364xA User’s and Service Guide III

Safety Symbols

The following symbols on the instrument and in the documentation

indicate precautions which must be taken to maintain safe operation of

the instrument.

Caution, risk of danger (refer to this manual

for specific Warning or Caution information) In position of a bi-stable push control

DC (Direct current or voltage)

Terminal is at earth potential. Used for

measurement and control circuits designed to

be operated with one terminal at earth

potential.

AC (Alternating current or voltage) Positive binding post

Protective conductor terminal Negative binding post

Out position of a bi-stable push control

IV E364xA User’s and Service Guide

Safety Considerations

Read the information below before using this instrument.

The following general safety precautions must be observed during all

phases of operation, service, and repair of this instrument. Failure to

comply with these precautions or with specific warnings elsewhere in this

manual violates safety standards for design, manufacture, and intended

use of the instrument. Keysight Technologies assumes no liability for the

customer’s failure to comply with these requirements.

CAUTION

•Use the device with the cables provided with the shipment.

•If the device is used in a manner not specified by the manufacturer,

the device protection may be impaired.

•Always use a dry cloth to clean the device. Do not use ethyl alcohol

or any other volatile liquid to clean the device.

•Do not permit any blockage of the ventilation holes of the device.

E364xA User’s and Service Guide V

This power supply is a Safety Class I instrument, which means that it has a

protective earth terminal. This terminal must be connected to earth ground

through a power source with a 3-wire ground receptacle.

Before installation or operation, check the power supply and review this

manual for safety markings and instructions. Safety information for

specific procedures is located at the appropriate places in this manual.

WARNING

• Do not use MAINS supply cords by inadequately RATED cord.

Always use the MAINS supply cord provided by the manufacturer.

• Do not use the device if it appears damaged or defective. REMOVE

POWER and do not use the device until safe operation is verified

by service-trained personnel. If necessary, return the device to

Keysight for service and repair to ensure that the safety features

are maintained.

• Do not operate the device around flammable gases or fumes,

vapor, or wet environments.

• Observe all markings on the device before connecting any wiring

to the device.

• Turn off the output of the power supply before connecting to the

output terminals.

• When servicing the device, use only the specified replacement

parts.

• Do not install substitute parts or perform any unauthorized

modification to the device. Return the device to Keysight for

service and repair to ensure that the safety features are

maintained.

• Do not operate the device with the cover removed or loosened.

VI E364xA User’s and Service Guide

Safety and EMC Requirements

This power supply is designed to comply with the following safety and

Electromagnetic Compatibility (EMC) requirements:

• IEC61326-1:2005/EN61326-1:2006

• Canada: ICES/NMB-001: Issue 4, June 2006

• Australia/New Zealand: AS/NZS CISPR11:2004

• IEC 61010-1:2001/EN 61010-1:2001

• Canada: CAN/CSA-C22.2 No. 61010-1-04

• USA: ANSI/UL 61010-1:2004

Environmental Conditions

This instrument is designed for indoor use. The table below shows the

general environmental requirements for this instrument.

Environmental condition Requirements

Temperature

Operating condition

•0 °C to 40 °C (full rated output)

Storage condition

•–20 °C to 70 °C

Humidity Operating condition

•95% RH (maximum)

Altitude Up to 2000 m

Installation category II (for indoor use)

Pollution degree 2

E364xA User’s and Service Guide VII

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The C-tick mark is a registered

trademark of the Spectrum

Management Agency of Australia. This

signifies compliance with

the Australia EMC Framework

regulations under the terms of the

Radio Communication Act of 1992.

ICES/NMB-001 indicates that this ISM

device complies with the Canadian

ICES-001.

Cet appareil ISM est confomre a la

norme NMB-001 du Canada.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical or electronic product in

domestic household waste.

The CSA mark is a registered

trademark of the Canadian Standards

Association.

This symbol indicates the time period

during which no hazardous or toxic

substance elements are expected to

leak or deteriorate during normal use.

Forty years is the expected useful life

of the product.

This symbol is a South Korean Class A

EMC Declaration. This is a Class A

instrument suitable for professional

use and in electromagnetic

environment outside of the home.

VIII E364xA User’s and Service Guide

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

This instrument complies with the WEEE Directive (2002/96/EC) marking

requirement. This affixed product label indicates that you must not discard

this electrical or electronic product in domestic household waste.

Product Category:

With reference to the equipment types in the WEEE directive Annex 1, this

instrument is classified as a “Monitoring and Control Instrument” product.

The affixed product label is as shown below.

Do not dispose in domestic household waste.

To return this unwanted instrument, contact your nearest Keysight Service

Center, or visit

www.keysight.com/environment/product

for more information.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Technologies Alimentation

Keysight Technologies

Keysight Technologies N2779A Manuel utilisateur

Keysight Technologies

Keysight Technologies U3606A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36100B Series Manuel de service

Keysight Technologies

Keysight Technologies B2961A Manuel d'installation

Keysight Technologies

Keysight Technologies RP7900 Series Manuel de service

Keysight Technologies

Keysight Technologies E3633A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36300 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N8921A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36300 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies RP7970 Series Manuel de service

Keysight Technologies

Keysight Technologies N6900 Series Manuel de service

Keysight Technologies

Keysight Technologies N69100 Series Manuel de service

Keysight Technologies

Keysight Technologies 66312A Manuel utilisateur

Keysight Technologies

Keysight Technologies 6611C Manuel utilisateur

Keysight Technologies

Keysight Technologies E36200 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies EDU36311A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36150 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies E3620A Manuel de service

Keysight Technologies

Keysight Technologies N6700C Series Manuel utilisateur

Keysight Technologies

Keysight Technologies E36100 Series Manuel de service

Keysight Technologies

Keysight Technologies E364xA Series Manuel

Keysight Technologies

Keysight Technologies 87421A Manuel de service

Keysight Technologies

Keysight Technologies E364 A Series Manuel

Keysight Technologies

Keysight Technologies U8030A Series Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur