Key Digital KD-EX18G Manuel utilisateur

4K with HDR HDMI Extender Tx + Rx Kit.

Extends 4K 18G to 35m (115ft), 1080p to 50m (164ft).

4K to 1080p Down Convert, HDMI Pass Thru, Power

over CAT, 2 Way IR, Handshake Control, Forced HPD

The Experts in Digital Video Technology and Solutions™

Operating Instructions

KD-EX18G

Table of Contents

Quick Setup Guide ..............................................................2

Application Example .............................................................3

Connections, Buttons, and LEDs.....................................................3

Speciﬁcations ..................................................................8

Important Product Warnings & Safety Instructions: .......................................9

Contacting Key Digital ............................................................9

Warranty Information.............................................................9

Always follow the instructions provided in this Operating Manual.

Please visit www.keydigital.com for the latest product documentation and software

downloads. Product features and speciﬁcations are subject to change without notice.

Introduction

Key Digital®KD-EX18G is a UHDoTP HDMI extender Tx + Rx set with 4K/UHD resolution and

bandwidth support up to 18Gbps and HDCP2.2 compliancy. KD-EX18G extends video resolutions

up to 4096x2160 at 60hz with 4:4:4 chroma sub-sampling over a single CAT5e/6 cable up to 115ft

(35m). 1080p signals are extended up to 164ft (50m). In addition to HDMI video and audio signals,

KD-EX18G carries IR for controlling remotely located equipment. KD-EX18G features 4K to 1080p

down convert, EDID handshake control, and hot plug detection integration tools, as well as an HDMI

pass-thru port for connecting to AV Surround Receivers or local monitors.

Key Features

›UHDoTP via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback,

equalization, and ampliﬁcation depending on cabling length

›4K Resolution Support: 4096x2160 or 3840x2160 24/25/30/60hz at 4:4:4 (signals up to

18Gbps bandwidth)

›Visually Lossless Compression: 18G enabling technology applied to all video formats exceeding

10.2Gbps to accommodate UHDoTP transmission channel

›4K to 1080p Down Convert: Optional resolution conversion applied at UHDoTP output provides

added integration options in retroﬁt installations as well as added distance performance

›10G Pass-thru: Mode enables uncompressed 10.2Gbps signal extension

›Flexible Power over CAT (PoC): Only one power connection needed. Tx may power Rx,

or Rx may power Tx.

›Low Proﬁle: Slim chassis design

›Signal Extension: For resolution and cable quality

»4K/UHD: Up to 35m (115ft) using CAT5e/6

»1080p: Up to 50m (164ft) maximum

›HDR10 (High Dynamic Range): More life-like images through a greater range of luminance levels

›HDCP 2.2: Compliancy up to HDCP 2.2 and backward compliant

›Deep Color Support: Up to UHD/4K 30Hz 4:4:4/12 bits or 60Hz 4:4:4/8 bit

›EDID Control: Internal library with 15 EDID handshakes including 4K with HDR in addition to native

EDID data from Output/Display device connected to Rx

›Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to

connected display/output device

›Full Buffer System™: Manages TMDS re-clocking / signal re-generation, HDCP authentication

with source & display, EDID handshake control, and Hot Plug Detection control

›IR Sensor: Sensor powering via +5V on IR In ports collects line-of-sight IR from remote(s) without

external IR connecting block

›Up/Down IR: Two channels of IR enable control to/from devices or control systems connected to Tx

and Rx units

›HDMI Pass-Through: Enables connection to local monitor or AV Receiver.

›Surround Audio Support: On HDMI pass-thru and UHDoTP outputs:

»HDMI Pass-Thru: Supports Dolby®, Dolby®TrueHD, DTS™and DTS-HD™(formats up to 7.1)

»UHDoTP Output: Supports Dolby®, DTS™(formats up to 5.1/6.1)

Included Accessories

›1x 12V/2A, 24W DC Power Supply (Screw-In Type). SKU: KD-PS12V2ASC

›4x Mounting Brackets

›1x IR Emitter, 1x IR Sensor

Quick Setup Guide

CONNECT:

Begin with the Tx and Rx units and all input/output devices turned off with power

cables removed.

1. Connect your HDMI source to the input port of the Tx unit

2. Connect your HDMI display to the output port of the Rx unit

3. Connect a CAT5e/6 cable between Tx and Rx unit. Use 568-B termination.

4. Connect IR emitter from Tx or Rx unit to the IR receptor of the device you wish to control.

5. Mount IR Sensor in a location that can easily collect line of sight IR signals from remotes.

Connect into the Tx or Rx unit’s IR In port.

»If hard-wired, IR is needed couple IR Emitter from control system to IR sensor

6. BEFORE connecting power supply to power outlet, screw-in the power supply to the Tx or Rx unit

7. AFTER all connections are made, plug-in power supply to power outlet

8. Power on source and display

CONFIGURE:

The default EDID handshake is 4Kx2K@60, 18G, HDR, 2ch audio (setting A) with 18G signal

bypass. Use the EDID rotary to choose desired handshake to provide to connected source and

the slide-switches to adjust 18G signal and hot plug detection handling.

Rack Mounting

In addition to mounting with the supplied L-Brackets, multiple KD-EX18G units may be mounted in

KD-SMS16 using the side mounting screws. KD-SMS16 is a mounting shelf for Key Digital units with

side mounting screw spacing of 2.912”, 2.582”, or 2.252”.

›Do NOT exceed 12 units as doing so will result in unit damage by overheating.

Application Example

Viewing RoomEquipment Rack

Remote

IR Sensor

HDMI

CAT5e/6

KD-EX18G

Cable / Satellite

IR Out

HDMI

Connections, Buttons, and LEDs

Before making any connections, power off your source and display devices.

HDMI Input & HDMI Output Connections

›HDMI Input: Using a short HDMI cable, connect your source device to the HDMI port labeled HDMI

Input.

›HDMI Output: Using a short HDMI cable, connect your display device to the HDMI port labeled

HDMI Output.

›For DVI-D/DVI-I sources or monitors, use appropriate adapters. For Display Port, use active

converters.

»Supports up to UHD/4K @ 50/60 fps [4:4:4], 18Gbps signals

»See Supported standard 4K Video Formats table

»Supports HDR10

»Compliant with HDCP 2.2 and previous

»Supports CEC pass thru

»HDMI Input & Pass-thru ports support Dolby®, Dolby®TrueHD, DTS™and DTS-HD™formats

up to 7.1ch

Supported standard 4K Video Formats:

Resolution Bandwidth

1 4K@24/25/30 [4:4:4] 8bit < 10.2Gbps

2 4K@24/25/30 [4:2:2] 8/10/12bit < 10.2Gbps

3 4K@50/60 [4:2:0] 8bit < 10.2Gbps

4 4K@24/25/30 [4:4:4] 10/12bit < 18Gbps

5 4K@50/60 [4:2:2] 8/10/12bit < 18Gbps

6 4K@50/60 [4:2:0] 10/12bit < 18Gbps

7 4K@50/60 [4:4:4] 8bit < 18Gbps

UHDoTP Output & UHDoTP Input Connections:

›Connect Tx unit’s UHDoTP Output port to Rx unit’s UHDoTP Input port using CAT5e/6 UTP or STP in

568-B termination.

»UHD/4K: Up to 115ft (35m)

»1080p: Up to 164ft (50m)

»Support Dolby®, DTS (5.1 formats max)

»Use with third-party Tx or Rx extenders is not supported

IR In & Out Connections:

›IR Control ports are simultaneous and bi-directional

»Tx Unit IR In corresponds with Rx unit IR Out. Tx Unit IR Out corresponds with Rx unit IR In.

»Rx Unit IR In corresponds with Tx unit IR Out. Rx Unit IR Out corresponds with Tx unit IR In.

›Only the provided IR Sensor and IR Emitter should be used. Third-party sensors or emitters may

not be compatible and/or may result in damage

IR In & Sensor:

›Connect sensor directly into the Tx or Rx unit’s IR In port to collect line-of-sight signals from device

remotes.

»No external IR distribution block or power supply is needed

›Receives signals from a 90° angle at up to 30 ft. away.

»Maximum supported IR burst frequency is 55kHz.

›IR In Pinout (3.5mm Stereo):

»Tip: IR Signal

»Ring: 5V Power for powering IR Sensor

»Sleeve: Ground

›IR In port does not support hard-wired control from control system / IR connection block.

»IR from a control processor or IR connection block should be achieved by coupling IR Emitter and IR

sensor

IR Out & Emitter:

›IR Out driving power: 5V with 32mA minimum current

›IR Out Pinout (3.5mm Mono)

»Tip: IR Signal

»Sleeve: Ground

›IR Emitter Wiring:

»Dashed/Marked wire: IR Signal

»Solid/No Marking: Ground

Power Connection:

›12V/2A (24W) power supply

›Only one power connection needed. May be connected at Tx or Rx unit

›Flexible Power over CAT (PoC). Tx may power Rx, or Rx may power Tx.

›Not compatible with third-party PoC devices

LED Indicator Lights:

›Power:

»Color: Blue

»Solid illumination during power on state, as provided by healthy connection with power supply

and healthy PoC extension.

»Steady blink if unit has is has a power short

›Live:

»Color: Yellow

»Steady blink from healthy unit CPU state

›UHDoTP Link:

»Color: Blue

»Solid illumination from healthy UHDoTP link between Tx and Rx units

›Video:

»Color: Orange

»Illumination with active TMDS (video + audio) signal

»Off with no TMDS (video + audio) signal

›HDMI Link:

»Color: Blue

»Tx Unit: Solid illumination from active signal from connected source

»Rx Unit: Solid illumination from active Hot Plug Detection voltage with connected display/output

device

EDID Rotary

»EDID authentication is provided from the Tx unit to the connected input/source device.

»The EDID ﬁle (AKA “handshake”) is selected using the EDID rotary on the unit and provides a list

of compatible video and audio formats as well as digital data, informing the source device what it

should output.

»Most sources will comply with a new EDID ﬁle without a power-cycle, but each source may

behave differently.

»Adjustments may be necessary to help achieve desired video and audio formatting and may

speed up sync time.

»The default EDID setting is position 7, 4K@60fps, 18G, 2ch audio

Position EDID Handshake Description EDID Rotary

0Copy EDID from Rx Display/Output

Note: Default position

is “7”

11080i, 2CH AUDIO

21080i, DOLBY/DTS 5.1

31080i, HD AUDIO

44Kx2K@60, 10.2G, HDR10, 2CH AUDIO

54Kx2K@60, 10.2G, HDR10, DOLBY/DTS 5.1

64Kx2K@60, 10.2G, HDR10, HD AUDIO

7 4Kx2K@60, 18G, HDR10, 2CH AUDIO

84Kx2K@60, 18G, HDR10, DOLBY/DTS 5.1

94Kx2K@60, 18G, HDR10, HD AUDIO

A1280x720p@60 DVI (no audio)

B1920x1080p@60 DVI (no audio)

C4Kx2K@60, 18G, 2CH AUDIO ➔1080p Downconvert at Rx IMPORTANT: Please

apply light pressure

to the EDID rotary

when making your

selection.

D4Kx2K@60, 18G, DOLBY/DTS 5.1 ➔1080p Downconvert at Rx

E4Kx2K@60, 18G, HD AUDIO ➔1080p Downconvert at Rx

FCopy EDID from HDMI Pass-through

Forced HPD Troubleshooting Tool:

In cases of many layers of connectivity or non-standard devices in-line, hot plug detection (HPD) may

be lost or drop below standard levels, leading to the video display not detecting a connected source and

resulting in no image.

›If set to ON, Hot Plug Detection (HPD) voltage is forced at the HDMI connection of the Rx unit.

The connected display will be fed a constant voltage to inform the device that a partner is always

connected and active.

›If set to OFF, Hot Plug Detection (HPD) voltage is passed-thru from connected source to the display

Speciﬁcations

Technical:

»Inputs Tx (Each): 1 HDMI, 1 IR

»Outputs Tx (Each): 1 UHDoTP, 1 IR

»Inputs Rx (Each): 1 UHDoTP, 1 IR

»Outputs Rx (Each): 1 HDMI, 1 IR

»Bandwidth: TMDS bandwidth 18Gbps

»Deep Color Support: Digital video formats in Deep Color Mode up to 12 bits per color

»DDC Communication: EDID and HDCP Bi-directional buffering from Display to Source

»HDMI Connector: Type A, 19 Pin Female

»RJ45 Connector: Shielded Link Connector, UHDoTP

»IR In & Out Connectors (Each): 3.5mm

»Power: (1) 12V/2A, 24W DC Power Supply (Screw-In Type). 100-240VAC, 50-60Hz.

Interchangeable transformer plug with screw-in connector. SKU: KD-PS12V2ASC

General:

»Regulation: CE, RoHS, WEEE, EAC

»Enclosure: Black Metal

»Product (Each): 4.1” x 2.8” x 0.875”, Weight: 0.75 lbs

Accessories:

»4x Mounting Brackets, 1x IR Emitter, 1x IR Sensor, 1x Power Supply

Table des matières

Autres manuels Key Digital Extenseur

Key Digital

Key Digital KD-CAT5XCAT5 Manuel utilisateur

Key Digital

Key Digital KD-4KWHCEX Manuel utilisateur

Key Digital

Key Digital KD-CATHD500Pro Manuel utilisateur

Key Digital

Key Digital KD-X222 Manuel utilisateur

Key Digital

Key Digital FatCAT KD-CATHD250Lite Manuel utilisateur

Key Digital

Key Digital KD-FIX418 Manuel utilisateur

Key Digital

Key Digital KD-HDMIWPRX Manuel utilisateur

Key Digital

Key Digital KD-X444LP Manuel utilisateur

Key Digital

Key Digital KD-CAT5XHDMI Manuel utilisateur

Key Digital

Key Digital KD-XUSB2 Manuel utilisateur

Key Digital

Key Digital KD-X422POA Manuel utilisateur

Key Digital

Key Digital FATCAT Series Manuel utilisateur

Key Digital

Key Digital KD-PS22UTx Manuel utilisateur

Key Digital

Key Digital KD-X411ProK Manuel utilisateur

Key Digital

Key Digital KD-CAT5XHDMI Manuel utilisateur

Key Digital

Key Digital KD-X444SP Manuel utilisateur

Key Digital

Key Digital KD-X422WP Manuel utilisateur

Key Digital

Key Digital KD-X444S Manuel utilisateur

Key Digital

Key Digital FatCAT KD-CATHD Tx Manuel utilisateur

Key Digital

Key Digital KD-CATHD300Lite Manuel utilisateur

Key Digital

Key Digital FatCAT KD-CATHD250POH Manuel utilisateur

Key Digital

Key Digital KD-HDDA1x1Pro Manuel utilisateur

Key Digital

Key Digital KD-IP120TX Manuel utilisateur

Key Digital

Key Digital Phantom KD-HD1X1ProK Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur