KERN NTEP Series Manuel de service

NTEP/NTNN-IA-defsi-0710

GB KERN NTEP/NTNN

Version 1.0 02/2007

Installation Information

Drive-through-scale

Contents

1General Description ........................................................................................ 13

2Standard Configuration and Working Principle............................................ 13

2.1 Major Components...............................................................................................13

2.2 Platform Assembly...............................................................................................14

2.3 Working Principle.................................................................................................14

3Specifications.................................................................................................. 15

3.1 Load Cell ...............................................................................................................15

4Inspection and Site Selection......................................................................... 15

4.1 Inspection..............................................................................................................15

4.2 Site Selection........................................................................................................16

5Installation ....................................................................................................... 16

5.1 Locate....................................................................................................................16

5.2 Installation Procedure..........................................................................................16

6Ramp Installation ............................................................................................ 19

7System Connection......................................................................................... 19

8Technical Data................................................................................................. 20

NTEP/NTNN-IA-defsi-0710 13

1 General Description

Thank you for choosing our NTEP/NTNN series floor scale. The scale consist of new

design ultra-low profile steel platform, four high precision shearing beam load cells.

NTEP/NTNN floor scales have the features of high accuracy, quick weighing and re-

liable weighing performance. The ultra-low platform means less effort required to

manually place the load on the scale. It is suitable to weigh drums, totes, small mix-

ing vats, etc.

The NTEP/NTNN series are designed to provide excellent performance required for

weighing applications in postal distribution centre, distribution centre of commerce,

storage and consignment enterprises, and workshop production line, semi finished or

finished product storehouse of pharmaceutical and food enterprises

2 Standard Configuration and Working Principle

2.1 Major Components

Figure 2-1 Major Components

1 Ramp (Option) 2 Platform

3 Instrument Cable 4 Lifting Eyebolt

5 Connecting Component (ramp) 6 Load Cell

7 Junction box 8 Cover

9 Limit support

NTEP/NTNN-IA-defsi-0710

2.2 Platform Assembly

The scales have a channel reinforced platform with two angle steel welding on two

sides of platform. The junction box is mounted on the angle steel. The covers on the

angle steel can be removed to gain access to the junction box. Threaded holes are

provided on two sides of platform. When installing or removing a platform, screw lift-

ing eyebolts into these holes and lift the platform by the eyebolts.

2.3 Working Principle

The elastic body of a load cell deforms under the weight onto the platform. The

Wheatstone bridge bonded to the elastic body loses its resistance balance and out-

puts an analog electric signal proportional to the weight. See Figure 2-2 for the Wiring

Scheme of Floor Scale with four load cells equipped.

Figure 2-2 Wiring Scheme

NTEP/NTNN-IA-defsi-0710 15

3 Specifications

3.1 Load Cell

SBC or SBH shearing beam load cells are provided in all NTEP/NTNN floor scales

with integral 6-conductor, shielded cables (see the table below). The load cell sus-

pension utilizes a rocker pin positioned between the cell and a fixed receiver in the

limit support (see Figure 5-3). The main features of the load cell are:

Recommended Excitation Voltage 6 - 15V (DC/AC)

Maximum Excitation Voltage 20 (DC/AC)

Rated Output 2 ±0.1% mV/V

Non-linearity 0.02% F.S.

Hysteresis 0.02% F.S.

Repeatability 0.01% F.S.

Creep (30 minutes) 0.02% F.S.

Output Terminal Resistance 350 ±1 Ohm

Safe Overload 150% F.S.

Ultimate Overload 250% F.S.

Function Color Code Function Color Code

+ Excitation Green - Excitation Black

+ Signal White - Signal Red

+ Sense Yellow - Sense Blue

Shield Yellow (Thicker)

4 Inspection and Site Selection

4.1 Inspection

Upon delivery of the NTEP/NTNN, visually inspect the scale for any damages which

may have occurred during shipment and handling. Inspect the following areas:

•Platform assembly for any warp.

•Load cell and suspension assemblies.

•Load cell cables.

•Load cell summing junction box.

•Overall platform assembly.

If any damage is found, please contact your freight carrier immediately.

NTEP/NTNN-IA-defsi-0710

4.2 Site Selection

Many problems associated with floor scale installations are caused by improper site

conditions. Before installing the scale, check the proposed location for the following

conditions:

•The area where the scale will be located should be level to within 4mm

from the highest to the lowest corner.

•The floor at each corner of the scale must be strong enough to maintain

support throughout the entire weighing capacity of the scale.

•There should be proper drainage away from the scale.

•There should be no heavy vibrations or wind currents at or near the scale.

•The scale should not be subjected to excessive or unusual loading due to

the location or type of equipment used.

If the site is acceptable, proceed with the installation. If not, choose a new location or

select another scale.

5 Installation

5.1 Locate

Place the NTEP/NTNN in the desired location after inspecting the site per Section 4

of this manual.

5.2 Installation Procedure

Place the scale to the ideal location – Pre-install the scale - Remove the platform with

eyebolts – Anchor the limit supports – Reinstall the platform - Route the instrument

cable - Check if installed properly.

NTEP/NTNN-IA-defsi-0710 17

5.2.1 Place Scale

Install eyebolts in the threaded holes provided on two sides of platform. Ensure that

the eyebolts are snug and fully threaded into the holes before lifting. Utilize the lifting

eyebolts when lifting the platform (see Figure 5-1).

Figure 5-1 Scale Lifting

5.2.2 Pre-install Scale

Disassemble the covers on two sides of platform. Place four limit supports under the

load cells, and install the platform. Oscillate the platform to ensure that the rocker

pins are seated in the receivers on the limit support and no binding exists. Place the

ramp at desired side of platform. Connect the ramp and limit supports by connecting

component with M10×15 bolts.

5.2.3 Remove Platform

Attach a chain or strap to the eyebolts, and lift the platform with a forklift or crane.

Take care to keep the positions of limit supports and connecting components.

5.2.4 Anchor Limit Supports

1. Locate the anchor holes in four limit supports. There are a total of 4 anchor

holes (1 per limit support).

2. Drill the anchor holes, using the limit support as a guide. Four M10 self-

expansion bolts are provided with each NTEP/NTNN floor scale for securing

limit supports to floor (see Figure 5-2).

3. All limit supports must bear pressure applied by platform. If the scale is out-of-

level or a limit support doesn’t bear pressure, shimming is required.

4. Secure the limit supports to the floor by installing the anchors and flat head

socket cap screws. The screws are provided with the scale. Be sure to use flat

head screws to maintain clearance between the head of the screw and the

bottom of the deck throughout the weighing range.

NTEP/NTNN-IA-defsi-0710

The weighing platform must be aligned with

the use of a water balance.

All foot screws must equally touch the

floor.

5.2.5 Reinstall Platform

1. Clear all debris from the scale area. Ensure that all four load pin receivers in the

limit support are clean and free of foreign material.

Figure 5-2 Top-of-Floor Installation

Figure 5-3 Suspension Details & δ

2. Replace the platform into the limit supports.

3. Oscillate the platform to ensure that the rocker pins are seated in the receivers

and no binding exists.

NTEP/NTNN-IA-defsi-0710 19

5.2.6 Route Instrument Cable

1. A loose coil of instrument cable should be stashed inside the angle steel, on

either side of the junction box assembly.

2. Route the instrument cable under the slot provided in the cover, stopping at

the indicator location.

3. Reinstall the covers on two sides of platform.

6 Ramp Installation (Option)

All model NTEP/NTNN floor scales have a single ramp to accommodate single traf-

fic. Order an optional ramp if dual direction traffic required. Select which side(s) of the

scale platform is to have a ramp attachment.

1. Each ramp is shipped complete with an attachment kit of parts: including four

bolts (M10×15), four washers (10) and four spring washers (10) for connecting

ramp and limit support by connecting component.

2. Insert the M10×15 bolts with washers and spring washers through the holes

on connecting component into the threading holes on limit support and ramp

(see Figure 6-1). Tighten the bolts then (see Figure 5-2).

3. Check to make sure that the ramp is stable and the gap S is between 3 ~ 7mm

(see chap. 5.2.5). Otherwise, shim with ϕ10 washers between limit support

and connecting component to meet this requirement.

7 System Connection

Load Cell Wiring Analog Instrument Cable

Function Color Function Color

+ Excitation Green + Excitation Green

+ Signal White + Signal White

- Excitation Black - Excitation Black

-Signal Red -Signal Red

Shield Yellow(thicker) Shield Yellow/Green

+Sense Yellow

-Sense Blue

Figure 7-1 System Connection DWG

NTEP/NTNN-IA-defsi-0710

8 Technical Data

KERN NTEP

600K200M NTEP

1.5T0.5M NTNN

600K200M NTNN

1.5T0.5M

Readability 200 g 500 g 200 g 500 g

Weighing range 600 kg 1500 kg 600 kg 1500 kg

Verification value 200 g 500 g 200 g 500 g

Minimum load 4 kg 10 kg 4 kg 10 kg

Accuracy class III

Dimensions (in mm) 1000 x 1000 x 45

Operating temperature -10°C bis 40°C

Operating humidity 10% ~ 95% relative humidity, non-condensing

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KERN Échelle

KERN

KERN MH5K5 Manuel utilisateur

KERN

KERN MPC 250K100NM Manuel utilisateur

KERN

KERN MBC Series Manuel utilisateur

KERN

KERN PCD-A03 Manuel utilisateur

KERN

KERN EOB Manuel utilisateur

KERN

KERN TGC Series Manuel utilisateur

KERN

KERN ADB-C Series Manuel utilisateur

KERN

KERN FKA Manuel utilisateur

KERN

KERN SFB 10K1HIP Manuel utilisateur

KERN

KERN FIS 120K20 IP Manuel utilisateur

KERN

KERN RFC Series Manuel utilisateur

KERN

KERN MPU 250K100 Manuel utilisateur

KERN

KERN 573xxNM Manuel utilisateur

KERN

KERN MBB Manuel utilisateur

KERN

KERN MPE 200K-1HEM Manuel utilisateur

KERN

KERN EMS Manuel utilisateur

KERN

KERN EFB Manuel utilisateur

KERN

KERN PCB Manuel utilisateur

KERN

KERN KFA 600V20S Manuel utilisateur

KERN

KERN FTC Manuel utilisateur

KERN

KERN EWJ Manuel utilisateur

KERN

KERN PLT Manuel utilisateur

KERN

KERN MWN Series Manuel utilisateur

KERN

KERN KERN DE Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur