KERN KIB-A12 Manuel utilisateur

KERN & Sohn GmbH

Ziegelei 1

D-72336 Balingen

E-Mail: info@kern-sohn.com

Phone: +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.kern-sohn.com

Installation Instructions

Verification plug

KERN KIB-A12

Version 1.0

2019-02

KIB-A12-IA-e-1910

2 KIB-A12-IA-e-1910

KERN KIB-A12

Version 1.0 2019-02

Installation instructions for the verification plug

Contents

1Installation....................................................................................................... 3

1.1 Connect verification plug............................................................................................................. 3

1.2 Seal the verification plug: .......................................................................................................... 10

1.3 Complete the installation........................................................................................................... 10

1.4 Error report Err5......................................................................................................................... 10

2How to connect the platform ....................................................................... 11

KIB-A12-IA-e-1910 3

1 Installation

•Connect the verification plug to the KIB-TM display device as follows and then

adjust the weighing system. Once it has been successfully adjusted, the

display device is linked to the verification plug.

1.1 Connect verification plug

Connect the chip in the verification plug to CN7 (5 Pin) in the display device.

KIB-TM

Main circuit

board

Line colour Connect female Connect male Load cell

E+ / Sen+ Red 1 1 EXC+

S+ Green 3 3 SIG+

GND

Shield

GND

S- White 4 4 SIG-

E- / Sen- Black 2 2 EXC-

Identchip

main board

Line colour Connect female Connect male

IC GND Yellow 7 7: Identchip GND

IC signal Brown 6 6: Identchip signal

Open housing

4 KIB-A12-IA-e-1910

Remove the CN8/power

plug.

Undo all cables

Remove ferrite core

KIB-A12-IA-e-1910 5

Pull cable through

Reinsert sealing ring

Attach both parts (see

fig.) to the verification

plug cable

6 KIB-A12-IA-e-1910

Pull cable through and

put on the cover cap

Remove screws as

shown in the diagram

KIB-A12-IA-e-1910 7

Slide the shrink tubing

over the cable of the

load cell so that it can be

sealed later.

Then solder the cable as

shown in the wiring

diagram (see chap. 1.1).

Insert the board as

shown in the diagram

and secure with the 4

screws.

8 KIB-A12-IA-e-1910

Reinsert the ferrite core

Connect the cable as

shown in the connection

plan

Connect the remaining

cables to the board

KIB-A12-IA-e-1910 9

Reconnect CN8

externally

Close K1 jumper,

K1 activates the

verification plug.

The verification plug

does not function

without K1.

10 KIB-A12-IA-e-1910

1.2 Seal the verification plug:

(Fig. Verification plug sealed)

Always seal the verification plug with a self-destructive seal.

Pull the shrink tubing over the connecting cables of the load cell or junction

box and seal with a self-destructive seal.

1.3 Complete the installation

After the verification plug has been installed

•Check software version

•Adjust the scale, K1 jumper must be set.

After adjustment, the scale must be switched off without fail and then

switched back on again.

The verification plug is finally configured correctly.

1.4 Error report Err5

Err 5 is shown if:

•The verification plug is not connected correctly

•The verification plug is defective

•The wrong verification plug has been connected

Table des matières

Autres manuels KERN Instrument de mesure

KERN

KERN DAB 200-2 Manuel utilisateur

KERN

KERN ORA 4 RR Manuel utilisateur

KERN

KERN ORA 10 BA Manuel utilisateur

KERN

KERN MBC-A01 Manuel utilisateur

KERN

KERN KKP V40 Series Manuel utilisateur

KERN

KERN TMBA-A01-A Manuel utilisateur

KERN

KERN MRS120-3 Manuel utilisateur

KERN

KERN DAB-SH-e-1610 Manuel utilisateur

KERN

KERN ORA 20 BA Manuel utilisateur

KERN

KERN MLB50-3 Manuel utilisateur

KERN

KERN DLT-N Manuel utilisateur

KERN

KERN DLB-A Manuel utilisateur

KERN

KERN ORA 3AA/AB Beer Manuel utilisateur

KERN

KERN ORA 1WA/WB Manuel utilisateur

KERN

KERN MAP 80K1 Manuel utilisateur

KERN

KERN DBS Manuel utilisateur

KERN

KERN TMBA-A01-A Manuel utilisateur

KERN

KERN DLB 160-3A Manuel utilisateur

KERN

KERN MLB-A03 Manuel utilisateur

KERN

KERN ORA 10 BB Manuel utilisateur

KERN

KERN MBA-A01 Manuel utilisateur

KERN

KERN KFE-TM Manuel utilisateur

KERN

KERN ORA 62 BA Manuel utilisateur

KERN

KERN MLS 50-3IR160 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur