Kenwood TS-2000 Manuel

Adjustment mode operation procedure

There is only one way to adjust the settings.

The only way to do so is with the adjustment Mode menu.

This menu has workt from 00 to 126.

TAKE CARE WITH IT USE AT YOUR OWN RISK!!!!!!!!!!!!!!!!!!!

Adjustment mode:

The TS 2000 can be adjusted manually (by turning a coil, trimmer, etc

or by setting the service adjustment mode (simply referred to as the

adjustment mode below)

adjustments items are shown in menu No: 00 to 126.

and all data are saved in the EEPROM (x53-391: IC7) :-)

To enter adjustment mode, the user firmware in the main unit must be

rewritten with adjustment firmware (The user firmware is the factory

setting)

MAKE SURE YOU HAVE THE USER FIRMWARE AS A BACK UP!!!!!!!!!!!!!!!!!!!

(we do not think we have to explane to you how to get the firmware

and how to upload it in the set in case of a crash if we have to do

that please do not start this procedure at all.!!!!!!!!!!!!!!!)

Oke let's go to step 2.

main way (frame) to do the job, only the main things are mentioned and

the explanation will be followed later on.

1) Checksum confirmation.

Switch the transceiver on while pressing and hold N.R.

and MIC/CAR keys.

2)Preparation of uploading data.

1. Access menu No. 56 and select 9600 bps, then switch the

transceiver OFF.

2. Back up the user data in the transceiver (menu configuration and

Memory channel daqta)

Run the programming software (W05-0855-00), then select "Menu/MRch

read from RADIO"

Name the file and save it somewhere where you can find it easily.

3)Uploading the the adjustment firmware

1.Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).

2.Upload the adjustment firmware, using " adjust firmware write menu.

3.Turn the switch (S1) off in TX-RX1 unit (x57-605 A).

4)Turn the tranceiver ON while pressing A=B key to perform the full

reset.

4. Adjustments

5. Uploading the user firmware.

1.TURN THE SWITCH (S1) on IN TX-RX1 UNIT (X57-605 a).

2.Upload the user firmware, using"user firmware write" menu.

3.Turn the switch (S1) OFF in Tx-Rx1 unit.

4.Turn the transceiver ON while pressing A=B key to perform the full

reset.

6. Checsum confirmation

Switch the transceiver on while pressing and hold N.R. and mic/car

keys.

If the user firmware has not changed, the checsum is the same as the

value in step 1.

If the user firmware has been updated the checsum should match the

new checksum.

7.Uploading the user firmware.

1. Turn the transceiver on while pressing a=b key to perform the full

reset.

2. Run the programming software (w05-0855-00), then select

menu/MRch Write to the radio.

PROCEDURE FOR WRITING ADJUSTMENT FIRMWARE (FOR BOTH USER AND

ADJUSTMENT FIRMWARE)

1. REMOVE THE LOWER CASE AND SET THE SLIDE SWITCH (S1) of the TX-RX 1

unit (x57-605A) to on (move the switch toward the front)

2. Connect the RS 232 C port of the personal computer with the COM

port of the main unit with a D-SUB (9-pin) straight cable (female-

female) this is the same cable as you use for all other software

comminication with the set.

3.Connect the external power suply put it ON The main unit does not

turn on any indicators, but it is ready to rewrite firmware.

Do not operate the power switch on the main unit!!!!!

4. write firmware using the writing software. there is a help file

with the software!!

5.After writing the the firmware turn the external power suply OFF

and remove the rs 232 cable.

6. Set the slide switch (you know now where it is??? :-)

(s1) to off (move the4 switch toward the rear)

7.Turn the external power suply ON

8.Turn the main unit ON and confirm that the indicator lights.

Then perform all reset (hold down A=B key and press the power key and

confirm that the initial state is displayed.

9. After adjustment rewrite adjustment software back to user firmware

using the writing software.

10.After rewriting user software, check the checsum (hold down the

N.R. and MIC/CAR keys and press the POWER key. then Menu No 125.

Then, perform all reset.

Notes

When adjustment software is loaded and the main unit is turned ON, A

beep sounds to indicate the adjustment mode. THIS DOES NOT INDICATE A

FAILURE.

Whenany key (exept PF key is pressed after a frequency is displayed,

the beep stops.

Adjustment mode operation procedure.

1. Start the adjustment mode.

Hold down th NR an mic/car keys and press the Power key.

The adjustment mode is set and a menu number is displayed below the

M.CH on the main band side (left) of the display.

2. Select adjustment mode menu number.

Turn the MULTI CH knob to change the menu No.

3. Change adjustment mode setting data.

Setting data can be changed with + or - key.

4.Write adjustment mode data.

Press + or - key on the main unit op UP or DOWN key on the microphone

on menu 124. witch will wrhite the eeprom.

5.Cancel adjustment Mode.

Press the CRL key to return to the normal VFO mode.

When the power is turned OFF in the middle in the adjustent mode, it

is canceled.

Autres manuels pour TS-2000

Table des matières

Autres manuels Kenwood Émetteur-récepteur

Kenwood

Kenwood TH-28A Manuel utilisateur

Kenwood

Kenwood PKT-23 Manuel utilisateur

Kenwood

Kenwood TS-790A/E Manuel utilisateur

Kenwood

Kenwood TS-850S Manuel utilisateur

Kenwood

Kenwood TS-930S Manuel utilisateur

Kenwood

Kenwood TM-V7A/E Manuel utilisateur

Kenwood

Kenwood TK-8100 Manuel utilisateur

Kenwood

Kenwood TK-5210G K Manuel utilisateur

Kenwood

Kenwood TS-990S Manuel utilisateur

Kenwood

Kenwood TS-850S Manuel utilisateur

Kenwood

Kenwood TM-G707A Manuel utilisateur

Kenwood

Kenwood TK-7180 Manuel utilisateur

Kenwood

Kenwood TS-530SP Manuel utilisateur

Kenwood

Kenwood TK-7160 Manuel utilisateur

Kenwood

Kenwood UBZ-LF14 Manuel utilisateur

Kenwood

Kenwood TR-2500 Manuel utilisateur

Kenwood

Kenwood TK-2107 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Kenwood

Kenwood TS-711A Manuel utilisateur

Kenwood

Kenwood NX-3320E3 Manuel utilisateur

Kenwood

Kenwood Nexedge NX-5200 Manuel utilisateur

Kenwood

Kenwood TS-120S Manuel utilisateur

Kenwood

Kenwood TK-2212 Manuel utilisateur

Kenwood

Kenwood TK-190K Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur

Uniden

Uniden UH820 Series Manuel utilisateur

Standard Horizon

Standard Horizon HX320E Manuel utilisateur

Em-Trak

Em-Trak A100 Manuel utilisateur

HPE

HPE Aruba QSFP28 Manuel utilisateur