Kenwood TK-2306 Manuel utilisateur

INSTRUCTION MANUAL

09 08 07 06 05 04 03 02 01 00

VHF FM TRANSCEIVER

TK-2306

UHF FM TRANSCEIVER

TK-3306

Thank You

We are grateful you have chosen Kenwood for your land

mobile radio applications.

noTices To The user

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

Safety: It is important that the operator is aware of, and

understands, hazards common to the operation of any

transceiver.

PrecauTions

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by Kenwood.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inflammable gas, dust particles, metallic

powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the instructions

and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the

vehicle is running. When the airbag inflates, the transceiver may

be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if any

metallic parts are exposed from the antenna covering. Transmitting

at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately, remove

the battery pack from the transceiver, and contact your Kenwood

dealer.

• Use of the transceiver while you are driving may be against traffic

laws. Please check and observe the vehicle regulations in your

area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects,

as they may short the battery terminals.

• When operating the transceiver in areas where the air is dry, it is

easy to build up an electric charge (static electricity). When using

a earphone accessory in such conditions, it is possible for the

transceiver to send an electric shock through the earphone and to

your ear. We recommend you use only a speaker/microphone in

these conditions, to avoid electric shocks.

Information concerning the battery pack:

The battery pack includes flammable objects such as organic

solvent. Mishandling may cause the battery to rupture

producing flames or extreme heat, deteriorate, or cause other

forms of damage to the battery. Please observe the following

prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into flame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-necklace or

hairpins). If the battery pack is short-circuited, excessive current will

flow and the battery may generate heat or smoke, rupture, or burst

into flame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

• Do not use or leave the battery near fire, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the

battery may generate heat or smoke, rupture, or burst into flame.

• Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

• Do not charge the battery near fire or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

iii

• Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit

is damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current

may flow upon discharging. The battery may generate heat or

smoke, rupture, or burst into flame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be reverse-

charged and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing

your eyes. Go to the hospital immediately. If left untreated, it may

cause eye-problems.

• Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate heat

or smoke, rupture, or burst into flame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and may cause the battery to

generate smoke or burst into flame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not use

it. The battery may generate heat or smoke, rupture, or burst into

flame.

CONTENTS

UNPACKING AND CHECKING EQUIPMENT.........................1

PREPARATION .........................................................2

ORIENTATION ..........................................................6

PROGRAMMABLE AUXILIARY FUNCTIONS........................7

BASIC OPERATIONS ..................................................9

VOICE OPERATED TRANSMISSION (VOX) ....................... 10

BACKGROUND OPERATIONS ...................................... 11

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. If any of the items listed

below are missing or damaged, file a claim with the carrier

immediately.

Supplied AcceSSorieS

• Antenna ..................................................................................1

• Battery charger/ AC adapter (KSC-31)...................................1

• Ni-Cd Battery pack (KNB-30A)...............................................1

• Speaker/ microphone jack cover ............................................1

• Speaker/ microphone locking bracket ....................................1

• Belt clip (KBH-10)...................................................................1

• Screw set

• 3 x 6 mm (Black) ..................................................................... 1

• 3 x 8 mm ................................................................................. 2

• Instruction manual ..................................................................1

Note: Refer to "PREPARATION" for accessory installation

instructions.

PREPARATION

inStAlling/ removing the BAttery pAck

◆Do not short the battery terminals or dispose of the battery by fire.

◆Never attempt to remove the casing from the battery pack.

1Align the battery pack with the

back of the transceiver, then

press the battery pack and

transceiver firmly together until

the release latch on the base of

the transceiver locks.

2To remove the battery pack, lift

the safety catch on the base of

the transceiver, then press the

release latch underneath the

safety catch.

3While pressing the release

latch, pull the battery pack

away from the transceiver.

inStAlling the AntennA

Screw the antenna into the connector

on the top of the transceiver by

holding the antenna at its base and

turning it clockwise until secure.

Note: The antenna is neither a handle,

a key ring retainer, nor a speaker/

microphone attachment point. Using

the antenna in these ways may

damage the antenna and degrade your

transceiver’s performance.

Antenna

inStAlling the Belt clip

If necessary, attach the belt clip using

the two supplied 3 x 8 mm screws.

Note: If the belt clip is not installed, its

mounting location may get hot during

continuous transmission or when left

sitting in a hot environment.

Belt clip

Do not use glue which is designed to prevent screw loosening when

installing the belt clip, as it may cause damage to the transceiver. Acrylic

ester, which is contained in these glues, may crack the transceiver’s

back panel.

If you are not using a speaker/

microphone, install the cover over

the speaker/ microphone jacks using

the supplied 3 x 6 mm screw.

Note: To keep the transceiver water

resistant, you must cover the speaker/

microphone jacks with the supplied

cover.

inStAlling the cover over the SpeAker/ microphone JAckS

inStAlling the optionAl SpeAker/ microphone (or heAdSet)

1Insert the speaker/ microphone

(or headset) plugs into the

speaker/ microphone jacks.

2Attach the locking bracket using

the supplied 3 x 6 mm screw.

Note: The transceiver is not fully

water resistant while using the

speaker/ microphone.

Speaker/ microphone

locking bracket

Speaker/ microphone

jack cover

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kenwood Émetteur-récepteur

Kenwood

Kenwood TK-U100V Manuel utilisateur

Kenwood

Kenwood TK-860HG Manuel utilisateur

Kenwood

Kenwood TR 7800 Manuel utilisateur

Kenwood

Kenwood NX-320 Series Manuel utilisateur

Kenwood

Kenwood UBZ-LJ9SETT Manuel utilisateur

Kenwood

Kenwood TK-D740HV Manuel utilisateur

Kenwood

Kenwood TK-780 series Manuel utilisateur

Kenwood

Kenwood TM-421A Manuel utilisateur

Kenwood

Kenwood TK-480 Manuel utilisateur

Kenwood

Kenwood TS-570D, TS-570S Mode d’emploi

Kenwood

Kenwood NEXEDGE NX-411K2 Manuel utilisateur

Kenwood

Kenwood TK-U100 Manuel utilisateur

Kenwood

Kenwood FreeTalk XL Manuel utilisateur

Kenwood

Kenwood TK-8360 Manuel utilisateur

Kenwood

Kenwood UHF P25 Transceiver TK-5810 Manuel utilisateur

Kenwood

Kenwood TK-6110 Manuel utilisateur

Kenwood

Kenwood ProTalk NX-P500 Manuel utilisateur

Kenwood

Kenwood NEXEDGE NX-200 Manuel utilisateur

Kenwood

Kenwood TK-3400 Manuel utilisateur

Kenwood

Kenwood TS-830S Manuel utilisateur

Kenwood

Kenwood TV-502 Manuel utilisateur

Kenwood

Kenwood TS-830S Manuel utilisateur

Kenwood

Kenwood TK-7302H Manuel utilisateur

Kenwood

Kenwood TR-9000 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur

Uniden

Uniden UH820 Series Manuel utilisateur

Standard Horizon

Standard Horizon HX320E Manuel utilisateur

Em-Trak

Em-Trak A100 Manuel utilisateur

HPE

HPE Aruba QSFP28 Manuel utilisateur