Kamstrup MULTICAL 302 Manuel utilisateur

Kamstrup A/S · Industrivej 28, Stilling · DK-8660 Skanderborg · T: +45 89 93 10 00 · info@kamstrup.com · kamstrup.com

Installation and User Guide

MULTICAL® 302

2 Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

MID designations

Permissible operating conditions / measuring ranges

Clcultor q: 2 °C…150 °C DΘ: 3K…130K

Temperture sensor set q: 2 °C…150 °C DΘ: 3K…130K

Flow sensor q: 2 °C…130 °C

Also vilble s cooling meter with temperture rnge 2 °C...150 °C (lterntively 2 °C...50 °C) or

s combined het/cooling meter with temperture rnge 2 °C...150 °C, however with MID

pprovl on the het register only.

Mechanical environment

M1 nd M2 (ﬁxed instlltion with minimum vibrtion nd ﬁxed instlltion with considerble or

high vibrtion level, respectively).

Electromechanical environment

E1 (housing/light industry). The meter’s signl cbles must be drwn with  minimum distnce of

25 cm to other instlltions.

Climatic environment

Instlltion must tke plce in environments with non-condensing humidity nd in closed

loctions (indoors). The mbient temperture must be within 5 °C…55 °C. The ﬂow sensor, however,

my be instlled in condensing environments.

Maintenance and repair

The ﬂow sensor nd the temperture sensors must not be seprted from the clcultor. Repirs

require subsequent reveriﬁction in n ccredited lbortory.

3Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

Contents

1 Generl informtion 3

2 Temperture sensors 4

2.1 Mounting of temperture sensors 4

2.2 Coupling for direct sensor 4

3 Informtion codes "INFO" 5

4 Mounting of ﬂow sensor 6

4.1 Wll mounting of MULTICAL® 302 7

4.2 Flow direction 8

4.3 Instlltion position 8

4.4 Humidity nd condenstion 8

5 Mounting of clcultor 9

5.1 Compct mounting 9

5.2 Wll mounting 10

5.3 Position of clcultor 10

6 Bttery supply 10

7 Testing the function 11

8 Communiction 11

8.1 Wired M-Bus communiction 11

8.2 Wireless M-Bus communiction

(rdio) 11

9 Setup Mode 12

9.1 Chnging the instlltion position 13

9.2 Chnging the energy unit 14

1 General information

Please read this guide carefully before installing the energy meter.

In case of incorrect mounting, Kamstrup's guarantee obligations no longer apply.

Note tht the following instlltion conditions must be obeyed:

- Pressure stge: PN16/PN25, see mrking. The ﬂow sensor mrking does not pply to

enclosed ccessories.

- Pressure stge

sensor set type Ø 5.2: PN16 nd PN25

At medium tempertures bove 90 °C, nd below 15 °C, nd the clcultor should be wll-

mounted.

4 Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

2 Temperature sensors

The temperture sensors used to mesure inlet nd outlet tempertures, respectively, re 

mtched sensor set tht must never be seprted.

Temperture sensors re mounted in MULTICAL® 302 from the fctory. According to EN 1434, the

cble length must not be chnged.

The temperture sensor which is mounted in the ﬂow sensor from the fctory hs no mrking on

the sensor cble. The other sensor, which is mrked with  green plstic ring, must be mounted in

the "opposite" pipe compred to the ﬂow sensor.

2.1 Mounting of temperature sensors

MULTICAL® 302 comes with  Ø 5.2 mm Pt500 sensor pir (mtched sensors) with 1.5 m silicone

cble. This sensor type cn be used s direct sensor using  coupling nd n O-ring nd s pocket

sensor to be mounted in  sensor pocket.

One temperture sensor is mounted in the ﬂow sensor from the fctory. The other sensor ought to

be mounted s direct sensor. Alterntively, both sensors must be mounted in sensor pockets s

symmetricl sensor instlltion gives the best mesuring result. If one of the sensors is not to be

mounted in the ﬂow sensor, it must insted be mounted s close to the outlet of the ﬂow meter s

possible so tht the distnce between the ﬂow sensor nd the temperture sensor is mx. 12 cm.

Asymmetricl sensor instlltion (one direct sensor nd one pocket sensor) is only dvisble

where ntionl regultions llow this, nd never in systems with low differentil temperture nd/

or low wter ﬂow.

Example:

If the disply shows tht the ﬂow sensor is to

be mounted in the inlet pipe, the sensor with

the green plstic ring must be mounted in the

outlet pipe.

2.2 Coupling for direct sensor

Slide the enclosed plstic coupling into plce

from the end of the sensor tube until you feel

 click when the coupling hs reched the ﬁrst

knurling.

5Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

The coupling must not be pushed further down

thn the ﬁrst knurling.

No mtter where the direct sensor is instlled,

it is very importnt tht you observe the tole-

rnces stted in the drwing to the left. If not,

the O-ring my not provide correct seling.

0,1

Ø 9 -0,1

3 Information codes "INFO"

MULTICAL® 302 constntly monitors  number of importnt functions. If there is  serious error in

the mesuring system or instlltion,  ﬂshing "INFO" is displyed, nd n info code cn be red

by ctivting the push-button until the mesuring unit displys "INFO". The info code is only shown

if n error hs occurred, unless the meter is conﬁgured for "sttic info codes".

Info code Description Response time

0 No irregulrities -

1 Supply voltge hs been interrupted -

4 Temperture sensor T2 outside mesuring rnge < 32 secs.

8 Temperture sensor T1 outside mesuring rnge < 32 secs.

32 Temperture difference hs wrong polrity < 32 secs. nd 0.05 m3

128 Supply voltge too low < 10 secs.

16 Flow sensor with wek signl or ir < 32 secs.

2Flow sensor with wrong ﬂow direction < 32 secs.

If more thn one info code ppers t  time, the sum of info codes is displyed. If e.g. both

temperture sensors re outside mesuring rnge, info code 12 (info codes 4+8) is displyed.

Info codes 4 nd 8 re set when the temperture flls below 0.00 °C or exceeds 155.00 °C. Info

codes 4 nd 8 re lso set for short-circuited nd disconnected sensors.

Note: If Info = 4 or 8, the meter's energy clcultion nd volume ccumultion stop.

6 Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

4 Mounting of ﬂow sensor

Prior to instlltion of the ﬂow sensor, the

system should be ﬂushed nd protection

plugs/plstic diphrgms removed from the

ﬂow sensor.

Correct ﬂow sensor position (inlet or outlet)

ppers from the disply of MULTICAL® 302.

The ﬂow direction is indicted by n rrow on

the side of the ﬂow sensor.

The ﬂow sensor my be used in both PN16 nd

PN25 instlltions nd is vilble mrked

either PN16 or PN25 or mrked both PN16 nd

PN25, s required.

SECTION

A-A

SCALE

2 : 1

Tightening by hnd

O-ring

Gsket

12 mm

Enclosed couplings, if ny, re only intended for PN16. Suitble PN25 couplings must be used in

PN25 instlltions.

In connection with G¾x110 mm, it must be checked tht 12 mm thred run-out is sufﬁcient. See

ﬁgure below.

Stright inlet: MULTICAL® 302 requires neither stright inlet nor stright outlet to meet the Me-

suring Instruments Directive (MID) 2004/22/ EF nd EN 1434:2007. A stright inlet section is only

necessry in cse of hevy ﬂow disturbnces before the meter. It is recommended to follow the

guidelines of CEN CR 13582.

A Recommended ﬂow sensor position

B Recommended ﬂow sensor position

C Uncceptble position due to risk of ir

build-up

D Acceptble position in closed systems

E A ﬂow sensor should not be plced

immeditely fter  vlve, except for block

vlves, which must be fully open when not

used for blocking

F A ﬂow sensor should not be plced close to

the inlet side of  pump

G A ﬂow sensor should not be plced close to

 two-level double bend.

In order to prevent cvittion, the operting pressure t MULTICAL® 302 must be min. 1 br t qp

nd min. 2 br t qs. This pplies to tempertures up to pprox. 80 °C.

MULTICAL® 302 must not be exposed to pressure lower thn the mbient pressure (vcuum).

7Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

4.1 Wall mounting of MULTICAL® 302

MULTICAL® 302 cn be mounted verticlly,

horizontlly or t n ngle.

90° 90°

90°

MULTICAL® 302 my be turned upwrds to mx

45° nd downwrds to mx 90° compred to

the pipe xis.

45°

90°

45°

90°

Important!

The meter is most sensitive to ir bubbles in the

wter when the plstic cse points upwrds.

Therefore, this mounting position ought only

to be used in instlltions with high operting

pressure nd utomtic ventiltion like e.g.

direct connected district heting.

8 Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

4.2 Flow direction

When the meter is instlled in the ppliction,

it must be ensured tht the ﬂow direction is

correct.

Flow direction out of the ﬁgure – the direction is

indicted on the ﬂow sensor.

Flow direction into the ﬁgure – the direction is

indicted on the ﬂow sensor.

4.3 Installation position

In the upper left corner of the meter disply, n

icon indictes if the meter is positioned in the

inlet or outlet pipe.

It is very importnt to ensure tht the meter

is correctly positioned s either inlet meter or

outlet meter. The instlltion position of the

meter cn be chnged in the Setup Mode (for

further informtion, see prgrph 9.1, pge

13).

Icon for inlet meter

Icon for outlet meter

4.4 Humidity and condensation

If MULTICAL® 302 is instlled in moist

environments, it must be turned 45° compred

to the pipe xis, s shown in the drwing to the

left.

45°

9Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

5 Mounting of calculator

5.1 Compact mounting

The clcultor is mounted directly on the

ﬂow sensor. The clcultor is seled from

the fctory, nd therefore, further seling is

unnecessry, unless the sels on the bck of

the clcultor hve been broken.

In cse of strong condenstion (e.g. cooling

pplictions), wll mounting of the clcultor is

recommended, see prgrph 5.2, pge 10.

24 59

In connection with compct mounting the cble

binder Aon the ﬂow cble cn be removed by

relesing the cble binder A. Subsequently

insert the cble binder through one of the

mounting eyes Bnd drw it round the cble

C. Finlly the cble binder is strpped round

the ﬂow cble gin tying the cble to the ﬂow

sensor D.

10 Kamstrup A/S • 55121351_D2_GB_04.2015

MULTICAL® 302

5.2 Wall mounting

The wll ﬁtting mkes it possible to mount

MULTICAL® 302 directly on n even wll. Use

the ﬁtting s  templte to mrk nd drill two 6

mm holes in the wll.

47 8

5.3 Position of calculator

If the ﬂow sensor is mounted in  humid or

condensing environment, the clcultor must

be plced in  higher position thn the ﬂow

sensor.

6 Battery supply

MULTICAL® 302 is bttery-supplied with either 1 or 2 A-cell btteries. Optiml bttery lifetime is

obtined by keeping the bttery temperture below 30 °C, e.g. by wll mounting.

The voltge of  lithium bttery is lmost constnt throughout the lifetime of the bttery

(pprox. 3.65 V). Therefore, it is not possible to determine the remining cpcity of the bttery by

mesuring the voltge. However, INFO code 128 indictes tht the bttery voltge is too low.

The bttery cnnot nd must not be chrged nd must not be short-circuited. Used btteries must

be hnded in for pproved destruction, e.g. to Kmstrup A/S.

Autres manuels pour MULTICAL 302

Table des matières

Autres manuels Kamstrup Instrument de mesure

Kamstrup

Kamstrup M-Bus Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 601 Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 603 Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 302 Manuel utilisateur

Kamstrup

Kamstrup 382 Manuel utilisateur

Kamstrup

Kamstrup flowIQ 2101 Manuel de la liste des pièces

Kamstrup

Kamstrup ULTRAFLOW 54 Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 801 Manuel utilisateur

Kamstrup

Kamstrup ULTRAFLOW 54 Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 62 Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 602 Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 41 Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 803 Manuel utilisateur

Kamstrup

Kamstrup flowIQ 3100 Manuel de la liste des pièces

Kamstrup

Kamstrup MAXICAL III Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 803 Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 403 Manuel de la liste des pièces

Kamstrup

Kamstrup READy Collector Manuel utilisateur

Kamstrup

Kamstrup OMNIPOWER Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 402 Instructions d'installation et d'utilisation

Kamstrup

Kamstrup flowIQ 3100 Series Manuel de la liste des pièces

Kamstrup

Kamstrup MULTICAL 41 Manuel utilisateur

Kamstrup

Kamstrup MULTICAL 602 Manuel de la liste des pièces

Kamstrup

Kamstrup ULTRAFLOW 54 DN150-300 Manuel de la liste des pièces

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur