Kaba Simplex LP1000 Series Manuel utilisateur

Resetting the Code/Combination From a Lost Code

Simplex LP1000

LP1000 Series FAQ

Resetting the Code/Combination From a Lost Code

Important: There is no procedure for nding an unknown combination from the front of the lock. A

lost combination must be cleared by removing the combination chamber from the lock housing, then

a new combination can be set.

1. Remove the back plate from the front lock housing by removing the six

back plate screws.

2. Remove the two Phillips head screws (F) securing the guide bracket (D

to the front housing. Grasp the guide bracket and slide it back to

disengage it from the clutch linkage (see gure 1).

3. Lift the two chamber links (A) o of the control shaft (B) using a small at

blade screwdriver. Mark links to assure proper reassembly (see gure 1).

4. Remove the combination chamber (E) by removing the Phillips head

screws (G) at each end of the chamber (see gure 1).

5. Remove shaft bushing (C) from control shaft (see gure 1).

6. Remove chamber cover marked ILCO UNICAN (A) (see gure 2) by gently

tapping the lip of the chamber cover (A) at the control shaft end of the

chamber (see gure 3) with a screwdriver to detach it from the staked

joints (B).

7. Lay the chamber on its side as shown in gure 4.

8. With tweezers, or other tool, slide the "E" ring (B) o the unlocking slide

stud (A) (see gure 17-4), then gently lift the end of the unlocking slide

(C) over the unlocking slide stud (A) (see gure 5).

Note: The unlocking slide (C) is under spring tension and will be easier to lift if

pushed to the left to ease tension. Swing the unlocking slide (C) suciently to

clear the gears, (D) no further than shown in gure 5.

9. Depress the lockout slide (E) as shown in gure 6. The gears (D) are now

free to rotate.

10. Turn each gear (D) so that the slots (F) are aligned as shown in gure 6.

11. Return the unlocking slide (C) over the unlocking slide studs (A) while making certain the

ve toes (G) are engaged in the ve gear pockets (F). It may be necessary to adjust each gear

(D) slightly to make proper alignment between toes and gear slots (see gures 6 & 7).

Re-secure the "E" ring on the stud (A). Your chamber will now resemble gure 7 and is ready

for reassembly with the lock housing.

REASSEMBLY

1. Re-secure the chamber cover (A) marked ILCO UNICAN. Make sure the staked joints (B)

(see gure 2) on both end plates t through both slots on the chamber cover.

2. Re-secure the shaft bushing (C) with at side facing up (see gure 8).

3. Secure the combination chamber with the two Phillips head screws (G) you removed earlier.

4. Re-secure the chamber links (A) onto the control shaft.

5. Replace the guide bracket (D) by aligning the clutch linkage in the guide bracket and secure

with the two Phillips head screws (F) previously removed.

6. Replace the back plate and secure it with the six back plate screws.

SETTING THE COMBINATION

Do not attempt to set a combination until the complete unit has been reassembled.

Perform the following steps in the order shown.

1. Turn the outside lever once to the stop position and then release.

2. Enter the new combination.

3. Turn the outside lever to the stop position, make sure the latch is fully retracted, then release

the lever.

KAA1166 0108

Autres manuels pour Simplex LP1000 Series

3

Table des matières

Autres manuels Kaba Serrure de porte

Kaba

Kaba ILCO Generation E-760 Series Manuel utilisateur

Kaba

Kaba Solitaire 710-II Series Manuel utilisateur

Kaba

Kaba E-PLEX 2000 Manuel utilisateur

Kaba

Kaba E-PLEX 5X51 Manuel utilisateur

Kaba

Kaba E-PLEX Manuel utilisateur

Kaba

Kaba E-PLEX STANDARD Series Manuel utilisateur

Kaba

Kaba E-PLEX 50XX SERIES Manuel utilisateur

Kaba

Kaba Saflok MT RFID Manuel utilisateur

Kaba

Kaba E30 Manuel utilisateur

Kaba

Kaba Ilco 790 Series Instructions de montage

Kaba

Kaba E-Plex 5x00 Cylindrical Manuel utilisateur

Kaba

Kaba Peaks Preferred Manuel utilisateur

Kaba

Kaba C-lever compact Manuel utilisateur

Kaba

Kaba 7002 Series Manuel utilisateur

Kaba

Kaba PowerLever 455 Series Manuel utilisateur

Kaba

Kaba PowerLever 1550 Manuel utilisateur

Kaba

Kaba Digital Cylinder Manuel utilisateur

Kaba

Kaba SIMPLEX 900 Series Manuel utilisateur

Kaba

Kaba E-Plex 5900 Manuel utilisateur

Kaba

Kaba EF 680E Manuel utilisateur

Kaba

Kaba LCLX Manuel utilisateur

Kaba

Kaba 5 00 Series Manuel utilisateur

Kaba

Kaba Solitaire 710-II Series Manuel utilisateur

Kaba

Kaba PowerLever 15 Series Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

Assa Abloy

Assa Abloy effeff 827A-IP Manuel utilisateur

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur