Küppersbusch IKD 9650.0 E Manuel utilisateur

Bedienungsanleitung

Instructions Booklet

Mode d’emploi

Libretto Istruzioni

Manual de instrucciones

IKD 9650.0 EIKD 9650.0 E

IKD 9650.0 E

16GB

CONTENTS

Dear Customer,

If you follow the recommendations contained

in this Instruction Manual, your appliance

will give you constant high performance and

will remain efficient for many years to come.

RECOMMENDATIONSANDSUGGESTIONS 17

CHARACTERISTICS 18

INSTALLATION 20

USE 24

MAINTENANCE 25

17GB

650 mm min.

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages

resulting from incorrect or improper installation.

• The minimum safety distance between the cooker top and the

extractor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on

the rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply

guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of

minimum diameter 120 mm. The route of the flue must be as

short as possible.

• Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical

appliances (e.g. gas burning appliances), a sufficient degree

of aeration must be guaranteed in the room in order to prevent

the backflow of exhaust gas. The kitchen must have an opening

communicating directly with the open air in order to guarantee

the entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic

use to eliminate kitchen smells.

• Never use the hood for purposes other than for which it has

ben designed.

• Never leave high naked flames under the hood when it is in

operation.

• Adjust the flame intensity to direct it onto the bottom of the

pan only, making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use:

overheated oil can burst into flames.

• The hood should not be used by children or persons not

instructed in its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply

before carrying out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid

detergent.

18GB

CHARACTERISTICS

Dimensions

370

898

75 890

min. 890

max. 1170

650 min.

509 96

144

19GB

12f

2.1

2.2

12h

7.1

12g

7.1a

7.1b

14.1

14.2

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light,

Blower, Filters

21 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with extractor,

consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

81 Air Outlet Grill

91 Reducer Flange ø 150-120 mm

14 1 Hood BodyAir Outlet Extension Piece

14.1 1 Air Outlet Connection Extension

14.2 1 Air Outlet Extension

15 1 Air Outlet Connection

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

20GB

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

Before starting installation, remove the Comfort Panels to prevent them from being damaged during

installation itself. Please consult the section on Maintenance on how to remove the panels.

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template

is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert the

Dowels 11 supplied).

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust

duct connection.

• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h, supplied.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

21GB

FIXING THE FRAME

• Unfasten the two screws fastening the upper

chimney stack 2.1 to the frame, and remove the

chimney from the upper stack.

If you wish to adjust the height of the frame,

proceed as follows:

• Unfasten the four safety screws located at the

top in the frame separation area. (A)

• Unfasten the eight metric screws joining the two

columns, located at the sides of the frame. (B)

• Adjust the frame to the height required, then

replace all the screws removed as above.

• To guarantee greater stability in the frame,

replace the four safety screws in the last hole

available.

• Insert the upper chimney stack from above, and

leave it running free on the frame.

• Lift the frame up, making sure that the index

over the frame plate is turned to the front.

• Fit the frame slots onto the two screws inserted

in the ceiling as above, and turn until reaching

the centre of the adjustment slot.

• Tighten the two screws and fasten the other two

screws provided; before locking the screws

completely, it is possible to adjust the frame by

turning it, making sure that the screws do not

come out of their housing in the adjustment slot.

• The Frame must be securely fastened so as to support both the weight of the Hood and the stress

caused by occasional axial pressure against the fitted Appliance. After fixing, make sure that the

base is stable even when the Frame is subjected to lateral stress.

• If the Ceiling is not strong enough in the area where the hood is to be fixed, the Installer must

strengthen the area using suitable plates and counterplates anchored to resistant structures.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid

pipe ø 150 or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection,

insert the reducer flange 9on the hood body

outlet.

• Fix the pipe using the pipe clamps 25 provided.

• Remove any activated charcoal filters.

ø 120ø 150

22GB

914.1

14.2

RECIRCULATION VERSIONAIR OUTLET

• Insert reducer flange 9on the extractor outlet.

• Push fit the extension piece 14 onto the flange.

• Push fit connector 15 onto the extension piece.

• Insert extension piece 14.2 laterally on

connector 15

• Insert extension piece/connector 14.1 laterally

on extension 14.2, ensuring that the outlet is in

line with the chimney intake.

Flue assembly - Mounting the hood body

• Position the upper chimney stack and fix the top of it

to the frame using 2 of the screws removed as above.

• Insert the lower chimney stack into the frame, holding

it in place with adhesive tape in the area separating

the lower chimney stack from the upper one.

Recirculation version

• Make sure that the outlet of the extension piece 14.1

is horizontally and vertically aligned with the chimney

outlet.

• If this is not the case, remove the lower Chimney Stack

and adjust the position of Extension 14; replace the

elements as described above.

Before fixing the Hood Canopy to the Frame:

• Remove the lighting unit; by turning the handle and

sliding the lever out of the fixing pin.

• Remove the activated charcoal filters, if fitted.

• Check that the screws provided to fix the hood canopy

to the frame have at least 4-5 mm between the head of

the screw and the frame plate.

• Hook the hood canopy to the frame and turn it to the

left until it reaches the stop, then lock the screws

immediately to prevent the hood canopy from falling

out accidentally.

• Remove the adhesive tape fixed to the lower chimney

stack as above, and rest the lower chimney stack

against the hood canopy.

• For the Recirculation Version, fit the directional grill

8into the housing provided. Also make sure that it is

properly fitted into connector 15.

23GB

Lux

Cmd

ELECTRICALCONNECTION

• Connect the Hood to the mains power supply, inserting

a two-pole cut-out switch with contact aperture of at

least 3 mm along the line.

• Remove the lighting unit, by turning the knob and

sliding the fixing pin lever.

• Ensure that the supply cable connector is properly

inserted into the Suction device socket

• Hook up the Commands connector Cmd.

• Hook up the Spotlights connector Lux to the socket

provided behind the lighting unit cover.

• For the Recirculation Version, fit the Activated

Charcoal Odour Filter.

• Replace the lighting unit.

24GB

USE

Control panel

BUTTON LED FUNCTIONS

L- Turns the lighting system on and off.

T1 0/1 Motor Fixed Turns the motor on and off.

Flashing 24h Exchange

Enabled by pressing and holding the button for approx. 3”.

Provides 100 m3/h suction with a noise level of just

28dB(A). To disable, press the button again and hold for

approx. 3”.

T2 Speed Decreases the working speed.

Flashing Delay (30’)

Press and hold the button for approx. 2” to enable a 30’

automatic delayed shutdown. Suitable to complete elimi-

nation of any residual fumes.

T3 Speed Increases the working speed.

T4 Speed Fixed Intensive speed.

Suitable to deal with maximum vapour emission, this turns

off automatically ten minutes after starting operation. It can

be disabled by pressing the button T4.

Flashing POWER function (maximum suction power)

Press T4 for approximately 3 seconds to enable the Power

function (maximum suction power), which is indicated by

flashing of the LED. This function will be revert to inten-

sive speed after 5 minutes or when T4 is pressed again.

S1 Led Fixed Signals triggering of the Metal Grease Filters saturation

alarm, indicating that the filters need washing. The alarm

is triggered after the Hood has been operating for 100 work-

ing hours. (Reset see paragraph on Maintenance)

Flashing When enabled, signals triggering of theActivated Charcoal

Filter, which must be replaced; the Metal Grease Filters

must also be washed. TheActivated Charcoal Filter satura-

tion alarm is triggered after the Hood has been operating

for 200 working hours. (Enabling and Reset see paragraph

on Maintenance)

I/P

resetdelay

T1 T2 T3 T4

Table des matières

Autres manuels Küppersbusch hotte de ventilation

Küppersbusch

Küppersbusch KD643.1 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 9650.0 E Manuel utilisateur

Küppersbusch

Küppersbusch IKD9350.0 Guide de configuration rapide

Küppersbusch

Küppersbusch EMD 700.0 Guide de configuration rapide

Küppersbusch

Küppersbusch EMA 950.0 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 957.1 GE Manuel d'utilisation

Küppersbusch

Küppersbusch IKD 10770.0 Manuel technique

Küppersbusch

Küppersbusch KD 674.1 GE Guide de configuration rapide

Küppersbusch

Küppersbusch KD 8950.0 Manuel technique

Küppersbusch

Küppersbusch IKDEM 976.1GE Guide de configuration rapide

Küppersbusch

Küppersbusch IKD 937.0 GE Manuel utilisateur

Küppersbusch

Küppersbusch EMA 800.0W Manuel utilisateur

Küppersbusch

Küppersbusch KD9980.0TGE Manuel de l'opérateur

Küppersbusch

Küppersbusch KD635.2 Guide de configuration rapide

Küppersbusch

Küppersbusch ED635.1 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 646.1 E Manuel d'utilisation

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

Küppersbusch

Küppersbusch KD.. 9700.0GE Manuel utilisateur

Küppersbusch

Küppersbusch IKD3700.0 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 9450 Manuel utilisateur

Küppersbusch

Küppersbusch KD 9550 Manuel utilisateur

Küppersbusch

Küppersbusch KD9875.1 Guide de configuration rapide

Küppersbusch

Küppersbusch IKD 9420.0 GE-CN Manuel d'utilisation

Küppersbusch

Küppersbusch KD 9420.0 GE-CN Manuel d'utilisation

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

Nibe

Nibe S Series Guide de l'utilisateur