Küppersbusch EDIP 6600 Fiche technique

GEBRAUCHS- UND

MONTAGEANWEISUNG

EDIP 6600

EDIP 6700

Operating and installation instructions

Mode d’emploi et notice de montage

Gebruiksaanwijzing en montagevoorschrift

Istruzioni d’uso e per il montaggio

Instrucciones de uso y de montaje

Instruções de serviçio e de montagem

de Seite 03–18

en page 19 – 34

fr page 35 – 50

nl pagina 51 – 66

it pagina 67 – 082

es página 83 – 098

pt página 99 – 114

min. 650 / 700 min. 430

Abb. 1

GAS ELEKTRO

GAZ ELECTR.

KAASU ELETT.

GASS EL.

Operating modes

This can be achieved if the combustion air

is able to ﬂow through non-lockable

openings, e.g. in doors, windows and in

conjunction with an air supply/air-intake wall

box or by other technical procedures such

as reciprocal interlocking.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

An air-intake/exhaust-air wall box by itself is

no guarantee that the limiting value will not

be exceeded.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

Unrestricted operation is possible if the

extractor hood is used in recirculating mode

– with activated carbon ﬁlter.

Circulating-air mode:

❑An activated carbon ﬁlter must be ﬁtted

for this operating mode (see Filters and

maintenance).

The complete installation set and

replacement ﬁlters can be obtained from

specialist outlets.

The corresponding accessory numbers

can be found at the end of these

operating instructions.

❑The extractor-hood fan extracts the

kitchen vapours which are puriﬁed in the

grease ﬁlter and activated carbon ﬁlter

and then conveyed back into the

kitchen.

❑The grease ﬁlter absorbs the grease

particles in the kitchen vapours.

❑The activated carbon ﬁlter binds the

odorous substances.

If no activated carbon ﬁlter is installed,

it is not possible to bind the odorous

substances in the cooking vapours.

Light / fan switches Filter drawer

Description of appliance

Operating instructions:

Operating modes

Exhaust-air mode:

❑The extractor-hood fan extracts the

kitchen vapours and conveys them

through the grease ﬁlter into the

atmosphere.

❑The grease ﬁlter absorbs the solid

particles in the kitchen vapours.

❑The kitchen is kept almost free of grease

and odours.

DIf the extractor hood is operated in

exhaust-air mode at the same time as a

ﬂue-type heater (e.g. gas, oil or solid-fuel

heater, instantaneous water heater, boiler),

ensure that there is an adequate air

supply which the heater requires for

combustion.

Safe operation is possible provided that the

partial vacuum in the room in which the

heater is installed does not exceed 4 Pa

(0.04 mbar).

Before using for the ﬁrst time

Important notes:

❑The Instructions for Use apply to several

versions of this appliance. Accordingly,

you may ﬁnd descriptions of individual

features that do not apply to your

speciﬁc appliance.

❑This extractor hood complies with all

relevant safety regulations.

Repairs should be carried out by

qualiﬁed technicians only.

Improper repairs may put the user at

considerable risk.

Do not ﬂambé food directly under the

extractor hood.

Risk of grease ﬁlter catching ﬁre due

!to ﬂames.

Restrictions apply to the use of the

extractor hood over a solid-fuel burner

(coal, wood, etc.). (See Installation

instructions).

Gas hobs / gas cookers

Always use gas hobs in a proper and

safe manner.

Important:

The ﬂames from the gas hob must always

be covered by pots or pans.

The intense heat generated by the gas

ﬂames could cause damage to the

!extractor hood.

❑Before using your appliance for the ﬁrst

time, please read these Instructions for

Use carefully. They contain important

information concerning your personal

safety as well as on use and care of the

appliance.

❑Please retain the operating and

installation instructions for a subsequent

owner.

Do not use the appliance if damaged.

The appliance is not intended for use

by young children or inﬁrmed persons

without supervision.

Young children should be supervised to

ensure they do not play with the appliance.

If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his

customer service or a similarly qualiﬁed

person in order to prevent serious injury to

the user.

The appliance may be connected to

the mains by a qualiﬁed technician only.

Dispose of packaging materials

properly (see Installation instructions).

Light bulbs must always be ﬁtted when

the extractor hood is in use.

Defective bulbs should be replaced

immediately to prevent the remaining bulbs

from overloading.

Never operate the extractor hood

without a grease ﬁlter.

Overheated fat or oil can easily catch

ﬁre.

If you are cooking with fat or oil, e.g. chips,

etc., never leave the cooker unattended.

Operating the extractor hood

The most effective method of removing

vapours produced during cooking is to:

❑Switch the ventilator ON

as soon as you begin cooking.

❑Switch the ventilator OFF

a few minutes after you have ﬁnished

cooking.

❑The fans in this appliance can be swit-

ched to the desired setting by hand

(manual mode) or can be controlled fully

automatically with the automatic function

according to your

requirements (automatic mode).

Switching on manual mode:

Press the Lor +button.

❑The fan starts at Setting }.

Switching over to automatic mode:

❑To switch from manual mode to

automatic mode at any time, press the Ü

button.

Fan – off –

Fan settings

– lower –

Fan – on –

Fan settings

– higher –

Intermittent

ventilation

Light

on / off

Display:

❑Fan settings / Intensive

setting

❑Saturation –

grease ﬁlter #

❑Saturation –

activated carbon ﬁlterr ã

Fan

on / off

Switching on the fan settings/intensive

setting:

1. To increase the fan settings or switch on

the intensive setting ç, press the +

button.

❑The intensive setting operates at

maximum power which should be

used only brieﬂy.

If the intensive setting is not switched

off manually, the fan automatically

switches back to Setting }after

10 minutes.

2. To switch off the intensive setting çor

switch back to fan settings ~–}–|and

switch off the extractor hood

completely, press the –button.

Appliances without automatic mode: Appliances with automatic mode:

(Ultraschall-Sensor)

Fan – off –

Fan settings – lower – Automatic mode

/ Manual mode

Fan – on –

Fan settings – higher – Intermittent

ventilation

Light

on / off Display:

❑Fan settings / Intensive

setting

❑Saturation –

grease ﬁlter #

❑Saturation –

activated carbon ﬁlterr ã

Fan

on / off

Operating the extractor hood

Switching on automatic mode:

Press the Übutton.

❑The fan runs at least at Setting |.

Fan settings:

❑If required, the optimum fan setting is

actuated automatically via a sensor.

❑The automatic function operates at

Settings |– ~.

Intensive setting:

1. To switch on the intensive setting ç,

press the +button.

❑Automatic mode has been switched

off.

❑The intensive setting operates at

maximum power which should be

used only brieﬂy.

If the intensive setting is not switched

off manually, the fan automatically

switches back to the optimum fan

setting after 10 minutes.

2. To switch off the intensive setting, press

the –button.

❑Automatic mode has been switched

on again.

Switching over to manual mode:

❑To switch from automatic mode to

manual mode at any time, press the Ü

button.

Intermittent ventilation

❑Used for ventilating the kitchen at hourly

intervals at the lowest fan setting, round

the clock.

Switching on appliance:

Press the button and insert the ﬁlter

drawer.

❑The fan runs for 5 minutes at Setting |,

then switches off for 55 minutes. This

process is repeated every hour.

Switching off:

Press the button.

Operating the extractor hood

Switching off:

There are 2 different methods of switching

off the appliance whether in manual or

automatic mode.

Switching off directly:

Press the Lbutton.

Important: All fan functions are switched

off.

Switching off appliance with fan run-on:

Insert ﬁlter drawer all the way. The fans

operate in the last switched-on stage for

around another 10 minutes and then switch

off.

❑If the intensive setting is switched on

when the ﬁlter drawer is inserted, the

intensive setting automatically switches

back during run-on.

❑If intermittent ventilation is switched on, it

continues operating normally following

run-on.

Light

❑The light can be used at any time, even

when the appliance has been switched

off.

Switching on/off: Press the abutton.

Adjusting the brightness:

❑Hold down the abutton until the

desired brightness is obtained.

❑After approx. 3 seconds the light

switches on to acknowledge the setting.

Switching off:

Repeat the process with the light switched

on.

❑After approx. 3 seconds the light

switches off to acknowledge the setting.

Adjusting the sensitivity of the sensor

control:

1. Press and hold down the automatic

button.

2. To display the current sensitivity, press

the +or –button.

3. You can now change the sensitivity of

the sensor control by pressing the +or

–button.

❑Factory setting: @.

❑Lowest setting: {.

❑Highest setting: Ö.

Special functions

Switching on the light automatically, e.g.

via a timer:

❑Fan and light must be switched off.

Switching on:

Simultaneously press the aand L

buttons.

Removing and inserting the metal-mesh

grease ﬁlters:

Warning: The halogen bulbs must be

switched off and cool.

1. Pull the ﬁlter drawer all the way out.

2. Depress both catches at the front of the

grease ﬁlter and remove the grease ﬁlter.

4. Clean the ﬁlters.

5. Insert the clean ﬁlters back into the hood.

6. Cancel the #display.

❑Press the Lbutton for at least

3 seconds.

The #display then goes out.

3. Depress the catches at the rear of the

grease ﬁlter and remove the grease ﬁlter.

Grease ﬁlters:

Metal-mesh ﬁlters are used to trap the

grease particles in the cooking vapours.

The ﬁlter mats are made from non-

combustible metal.

Caution:

As the ﬁlter becomes more and more satu-

rated with grease, there is an increased risk

of ﬁre and the function of the extractor

hood may be impaired.

Important:

By cleaning the metal grease ﬁlters at

appropriate intervals, the possibility of them

catching ﬁre as a result of a build-up of heat

such as occurs when deep-fat frying or

roasting is taking place, is reduced.

Saturation indicator:

When the grease ﬁlters reach saturation

point, an acoustic signal is sounded for 6

seconds after the fan has switched off, and

an #appears in the display. The grease

ﬁlters should be cleaned straight away.

Cleaning the metal-mesh grease ﬁlters:

❑The ﬁlters can be cleaned in a

dishwasher. However, they may become

slightly discoloured.

Important:

Do not wash highly saturated metal-

mesh grease ﬁlters with other utensils.

❑If cleaning the ﬁlters by hand, soak them in

a hot soap solution. Then brush the ﬁlters,

rinse thoroughly and leave to drain.

Filters and maintenance

Removing the ﬁlter:

Warning: The halogen bulbs must be

switched off and cool.

1. Remove the metal-mesh ﬁlters.

2. Depress the catches on both sides of

the ﬁlter and remove the activated

carbon ﬁlter.

3. Replacing the activated carbon ﬁlter:

❑A replacement ﬁlter can be obtained

from any authorized dealer.

❑Use original ﬁlters only.

This will ensure maximum

performance.

4. Insert the grease ﬁlters.

Disposing of the old activated carbon

ﬁlter:

❑Activated carbon ﬁlters do not contain

any pollutants and can be disposed of

with domestic refuse.

Filters and maintenance

3. Engage the catches at both sides.

4. Insert the metal-mesh grease ﬁlters (see

”Removing and inserting the metal-mesh

grease ﬁlters”).

5. Cancel the ãdisplay.

❑Press the Lbutton for at least

3 seconds.

The ãdisplay then goes out.

Saturation indicator:

When the activated carbon ﬁlter is satura-

ted, an acoustic signal is emitted for 6

seconds when the fan has switched off and

ãis displayed. The activated carbon ﬁlter

should then be replaced immediately.

Activated carbon ﬁlter:

For neutralizing odours in recirculating

mode.

Caution:

As the ﬁlter becomes more and more

saturated with grease, there is an increased

risk of ﬁre and the function of the extractor

hood may be impaired.

Important:

Change the activated carbon ﬁlter promptly

to prevent the risk of ﬁre from the

accumulation of heat when deep-fat frying

or roasting.

Inserting the ﬁlter:

Warning: The halogen bulbs must be

switched off and cool.

1. Remove the metal ﬁlters

(see "Removing and inserting the metal

grease ﬁlters").

2. Insert the activated carbon ﬁlter.

Cleaning and care

Isolate the extractor hood by pulling out

the mains plug or switching off the fuse.

❑When cleaning the grease ﬁlters, remove

grease deposits from accessible parts of

the housing. This prevents the risk of ﬁre

and ensures that the extractor hood

continues operating at maximum

efficiency.

❑Clean the extractor hood with a hot soap

solution or a mild window cleaner.

❑Do not scrape off dried-on dirt but wipe

off with a damp cloth.

❑Do not use scouring agents or abrasive

sponges.

❑Note: Do not use alcohol (spirit) on

plastic surfaces, as dull marks may

appear.

Caution: Ensure that the kitchen is ade-

quately ventilated. Avoid naked ﬂames!

Clean the operating buttons with a mild

soapy solution and a soft, damp cloth only.

Do not use stainless-steel cleaner to clean

the operating buttons.

Stainless steel surfaces:

❑Use a mild non-abrasive stainless steel

cleaner.

❑Clean the surface in the same direction

as it has been ground and polished.

Do not use any of the following to clean

stainless steel surfaces: abrasive sponges,

cleaning agents containing sand, soda, acid

or chloride!

Aluminium and plastic surfaces:

❑Use a soft, non-linting window cloth or

micro-ﬁbre cloth.

❑Do not use dry cloths.

❑Use a mild window cleaning agent.

❑Do not use aggressive, acidic or caustic

cleaners.

❑Do not use abrasive agents.

4. Re-insert the bulb ring.

5. Restore the power by inserting the mains

plug or switching on the fuse.

Note: If the light does not function, check

that the bulbs have been inserted correctly.

Replacing the light bulbs

1. Switch off the extractor hood and pull

out the mains plug or switch off the

electricity supply at the fuse box.

When switched on, the halogen bulbs

become very hot. Even for some time after

the bulbs have been switched off there is

still a risk of burns.

2. Remove the bulb ring with a screwdriver

or similar tool.

3. Replace the halogen light bulb

(conventional halogen bulb, 12 Volt,

max. 20 Watt, G4 bulbholder).

Caution: Plug-in bulbholder.

Take hold of the bulb with a clean cloth.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Küppersbusch hotte de ventilation

Küppersbusch

Küppersbusch EDL12700.0GE Manuel utilisateur

Küppersbusch

Küppersbusch CSW6870 0 Series Manuel d'utilisation

Küppersbusch

Küppersbusch KD 380.0 GE Manuel d'utilisation

Küppersbusch

Küppersbusch IKD 954.1 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 9650.0 E Manuel utilisateur

Küppersbusch

Küppersbusch KD 12460.0 Manuel technique

Küppersbusch

Küppersbusch DW9320 Manuel utilisateur

Küppersbusch

Küppersbusch KD 957.1 GE Manuel d'utilisation

Küppersbusch

Küppersbusch EDIP 649.0 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 965.1 Guide de configuration rapide

Küppersbusch

Küppersbusch HI981420 Manuel d'utilisation

Küppersbusch

Küppersbusch IKD9880.0 Guide de configuration rapide

Küppersbusch

Küppersbusch KD 8950.0 Manuel technique

Küppersbusch

Küppersbusch IKD 10770.0 Manuel technique

Küppersbusch

Küppersbusch IKDEM 976.2GE-84 Manuel utilisateur

Küppersbusch

Küppersbusch KD9575.0 Guide de configuration rapide

Küppersbusch

Küppersbusch KD635.2 Guide de configuration rapide

Küppersbusch

Küppersbusch IKD 9600 Manuel utilisateur

Küppersbusch

Küppersbusch D633.1 Guide de configuration rapide

Küppersbusch

Küppersbusch IKD15560.0 Guide de configuration rapide

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

Küppersbusch

Küppersbusch EDIP 6550.0 Guide de configuration rapide

Küppersbusch

Küppersbusch EDIP 633... Guide de configuration rapide

Küppersbusch

Küppersbusch EDIP 6650.0 Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

Nibe

Nibe S Series Guide de l'utilisateur