Kübler CODIX 54U Manuel utilisateur

english

Operating instructions

Electronic display counter

CCOODDIIXX5544UU

1.1 Safety instructions and warnings

Only use this display

– in a way according to its intended

purpose

– if its technical condition is perfect

– adhering to the operating

instructions and the general

safety instructions.

1.2 General safety instructions

1. Before carrying out any installation or maintenance

work, make sure that the power supply of the digital

display is switched off.

2. Only use this digital display in a way according to its

intended purpose:

f its technical condition is perfect.

Adhering to the operating instructions and the gen-

eral safety instructions.

3. Adhere to country or user specific regulations.

4. The digital display is not intended for use in areas

with risks of explosion and in the branches exclud-

ed by the standard EN 61010 Part 1.

5. The digital display shall only operated if it has been

correctly mounted in a panel, in accordance with

the chapter “Main technical features”.

1.3 Use according to the intended

purpose

The digital display may be used only as a panel-

mounted device. Applications of this product may

be found in industrial processes and controls, in

manufacturing lines for the metal, wood, plastics,

paper, glass, textile and other processing indus-

tries.

Over-voltages at the terminals of the digital dis-

play must be kept within the limits in Category II

If the digital display is used to monitor machines

or processes in which, in case of a failure of the

device or an error made by the operator, there

might be risks of damaging the machine or caus-

ing accidents to the operators, it is your responsi-

bility to take appropriate safety measures.

1.4 Description

CODIX 54U is a multipurpose device. Depending

on the programmed basic function, the device

operates like

• an electronic totaliser and frequency meter

(see page 2)

•anelectronic display counter with

2 totalising ranges (see page 4)

•anelectronic totaliser and time meter

(see page 6)

•anelectronic time meter with 2 time ranges

(see page 9)

2. Setting of the operating parameters

a. Press both front side keys keys and switch on

the supply voltage or, if the supply voltage is

already on, press both keys simultaneously

during 5 s.

b. The display shows

c. After releasing the keys, the display shows

c1.Hold the left key pressed and press the right

key to leave the programming operation.

c2.Press the right key to switch to

d. Hold the left key pressed and press the right

key to switch to the first parameter.

3. Programming routine

The first menu item is the selection of the basic

operating mode, which determines the functions

of the device.

Operating mode adding

counter and frequency

meter,

continued in point 4

on page 2

Operating mode display

counter with 2 totalising

ranges,

continued in point

on page 4

Operating mode totaliser

and time meter,

continued

in point 4

on page 6

Operating mode time

meter with 2 time ranges,

continued in point 4

page 9

e. After releasing the keys, the display alter-

nates between the menu title and the current

menu item setting. After pressing any key,

only the menu item setting is displayed.

f. Pressing the right key, the menu item setting

will be switched to the next value.

If figures are to be input (e.g. when setting

the scaling factor), select first the decade

using the left key, and then set the value

using the right key.

g. Hold the left key pressed and press the right

key to switch to the next menu item.

h. The last menu title ”EndPro” allows, when

selecting “Yes”, to exit the programming

menu and to take over (store) the new val-

ues.

If “no” is selected, the programming routine

is repeated, the latest values set remaining

active. They can now be checked again or

modified.

Electronic totaliser and frequency

meter

CCooddiixx5544UU: basic operating mode

1. Description

•

6-digit totaliser

and frequency meter

• Red LED display, character height 14 mm

• Display range 0 ... 999 999

• Leading zeros suppression

• Programming via two setting keys on the front

side

• During programming, the display guides the

user with text prompts

• Value conversion and display in 1/s oder 1/min

• With AC power supply: sensor supply

voltage 24 V DC ±15 %/100 mA

2. Inputs

INP A

Dynamic count/frequency input.

RESET

Dynamic RESET input. Linked in parallel to the

red RESET key. Resets the counter to zero.

3. Selection of the displayed value

Pressing the right key allows switching between

the totaliser display and the frequency meter dis-

play. Press the key briefly to display for 2 sec-

onds the current function (“total” or “tacho”). If,

during this period of time, the right key is pressed

a second time, the device switches to the current

function and displays a confirmation (“total” or

“tacho”) for 2 seconds. Then, the value of the

selected function is displayed.

4. Programming routine

The programmable parameters of the device are

described below, in the order in which they can

be set. The device is fully programmed after one

pass of the routine.

The first values stated correspond to the factory

setting

- Subject to change without prior notice -

english

4.1 Polarity of the inputs

npn: switching for 0 V

pnp: switching for +UB

4.2 Switching on the 30 Hz filter (INP A)

30 Hz filter off (fmax)

30 Hzfilter on

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.3 Multiplying factor (totaliser)

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.4 Dividing factor ( totaliser)

The decimal point defines

the way of displaying the

count values. It does not

affect counting.

0 no decimal place

0.0 one decimal place

0.00 two decimal places

0.000

three decimal places

4.5 Decimal point (totaliser)

- Subject to change without prior notice -

4.6 RESET-Mode (totaliser)

manual reset via the red

RESET key and electrical

reset via the RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

4.7 Multiplying factor (frequency meter)

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.8 Dividing factor (frequency meter)

The decimal point defines

the resolution.

0 no decimal place

0.0 one decimal place

0.00 two decimal places

0.000

three decimal places

4.9 Decimal point (frequency meter)

4.12 End of programming

The programming routine

is repeated once more.

The values set until now

can be checked and mod-

ified.

The programming routine

wil be left and all values

set will be stored as new

parameters.

Afterwards the device is

ready for operation.

4.10 Display mode (frequency meter)

Value conversion and

display in 1/s

Value conversion and

display in 1/min

4.11 Max. time to wait until „0“ is displayed

(frequency meter)

This parameter indicates, how long it takes, when

measuring is active, until „0“ is displayed.

Max. time to wait 00.1 s

(min. value)

Max. time to wait 99.9 s

Electronic display counter with

2 totalising ranges

CCooddiixx5544UU: basic operating mode

1. Description

• 6-digit dislay counter with Reset function

• Red LED display, character height 14 mm

• Display range 0 ... 999 999

• Leading zeros suppression

• Programming via two setting keys on the front

side

• During programming, the display guides the

user with text prompts

• With AC power supply: sensor supply

voltage 24 V DC ±15 %/100 mA

2. Inputs

INP A

Dynamic count input Counter 1 and Counter 2.

RESET

Dynamic RESET input. Linked in parallel to the

red RESET key. Sets the counter to zero. Can be

adjusted individually for Counter 1 and Counter 2.

3. Selection of the displayed value

Pressing the right key allows switching between

the display of totaliser 1 and the display of totalis-

er 2. Press the key briefly to display for 2 sec-

onds the current function (“total1” or “total2”). If,

during this period of time, the right key is pressed

a second time, the device switches to the current

function and displays a confirmation (“total1” or

“total2”) for 2 seconds. Then, the value of the

selected function is displayed.

4. Programming routine

The programmable parameters of the device are

described below, in the order in which they can

be set. The device is fully programmed after one

pass of the routine.

The first values stated correspond to the factory

settings

english

4.1 Polarity of the inputs

npn: switching for 0 V

pnp: switching for +UB

4.2 Switching on the 30 Hz filter (INP A)

30 Hz filter off (fmax)

30 Hzfilter on

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.3 Multiplying factor

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.4 Dividing factor

The decimal point defines

the way of displaying the

count values. It does not

affect counting.

0 no decimal place

0.0 one decimal place

0.00 two decimal places

0.000

three decimal places

4.5 Decimal point

4.6 RESET mode (totaliser 1)

manual reset via the red

RESET key and

electrical reset via the

RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

4.7 RESET Mode (totaliser 2)

manual reset via the red

RESET key and

electrical reset via the

RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

4.8 End of programming

The programming routine

is repeated once more.

The values set until now

can be checked and mod-

ified.

The programming routine

wil be left and all values

set will be stored as new

parameters.

Afterwards the device is

ready for operation.

Electronic totaliser and time meter

CCooddiixx5544UU: basic operating mode

1. Description

• 6 digit totaliser and time meter with Reset

function

• Red LED display, character height 14 mm

• Display range 0 ... 999 999

• Leading zeros suppression

• Programming via two setting keys on the front

side

• During programming, the display guides the

user with text prompts

• Operation indicator: the decimal point of the

lowest digit blinks while the count is active.

• Time meter operating modes:

– Counting while INP B is inactive “GAtE.Lo”

– Counting while INP B is active “GAtE.hi”

– Count Start/Stop with INP B edge B “Inb.Inb”

• Counting ranges: h; min; s; h.min.s

• With AC power supply: sensor supply

voltage 24 V DC ±15 %/100 mA

2. Inputs

INP A

Dynamic count input for the totaliser.

INP B

Start-/Stop or gate input for time meter

(independent of the input mode)

RESET

Dynamic RESET input. Linked in parallel to the

red RESET key. Sets the counter to zero. Can be

adjusted individually for the totaliser and the time

meter.

3. Selection of the displayed value

Pressing the right key allows switching between

the totaliser display and the time meter display .

Press the key briefly to display for 2 seconds the

current function (“total” or “time”). If, during this

period of time, the right key is pressed a second

time, the device switches to the current function

and displays a confirmation (“total” or “time”) for 2

seconds. Then, the value of the selected function

is displayed.

english

4. Programming routine

The programmable parameters of the device are

described below, in the order in which they can

be set. The device is fully programmed after one

pass of the routine.

The first values stated correspond to the factory

settinfs

4.1 Polarity of the inputs

npn: switching for 0 V

pnp: switching for +UB

4.2 Switching on the 30 Hz filter (INP A, INP B)

30 Hz filter off (fmax)

Count and start/stop

inputs not damped

30 Hz filter on

Count and start/stop

inputs damped

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.3 Multiplying factor (totaliser)

It can be set from 00.0001

up to 99.9999.

The decimal point is set to

4 decimal places.

„0“ is not accepted!

4.4 Dividing factor (totaliser)

The decimal point defines

the way of displaying the

count values. It does not

affect counting.

0 no decimal place

0.0 one decimal place

0.00 two decimal places

0.000

three decimal places

4.5 Decimal point (totaliser)

4.6 RESET mode (totaliser)

manual reset via the red

RESET key and electrical

reset via the RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

Start/Stop via Inp B.

Counting while Inp B

(Gate) not active or open

Start/Stop via Inp B.

Counting while Inp B (Gate)

active (High level with

pnp; Low level with npn)

Count

Start/Stop via

INP B

(LOW-HIGH edge with

pnp; HIGH-LOW edge

with npn). Every active

edge changes the counter

status.

4.7 Input mode (time meter)

Time unit: seconds (accu-

racy depending on posi-

tion of the decimal point*)

Time unit: minutes (accu-

racy depending on posi-

tion of the decimal point*)

Time unit: hours (accura-

cy depending on position

of the decimal point*)

Time units:

Hours:Minutes:Seconds

(decimal point setting is

ignored)

4.8 Operating mode (time meter)

*0, 0.1, 0.01, 0.001 means: time measurement in

0, 0.1, 0.01, 0.001 time units

4.9 Decimal point (time meter)

The decimal point defines

the resolution of the pro-

grammed time unit.

0.0 1/10 (0,1)

0.00 1/100 (0,01)

0.000 1/1000 (0,001)

4.11 End of programming

The programming routine

is repeated once more.

The values set until now

can be checked and mod-

ified.

The programming routine

wil be left and all values

set will be stored as new

parameters.

Afterwards the device is

ready for operation.

4.10 RESET mode (time meter)

manual reset via the red

RESET key and electrical

reset via the RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

english

Electronic tim meter with

2 time ranges

CCooddiixx5544UU: basic operating mode

1. Description

• 6 digit time meter with Reset function

• Red LED display, character height 14 mm

• Display range 0 ... 999 999

• Leading zeros suppression

• Programming via two setting keys on the front

side

• During programming, the display guides the

user with text prompts

• Operation indicator: the decimal point of the

lowest digit blinks while the count is active

• Time meter operating modes:

– Counting while INP B is inactive “GAtE.Lo”

– Counting while INP B is active “GAtE.hi”

– Count Start/Stop with INP B edge (Inb.Inb)

– Count Start with INP A edge, count Stop with

INP B edge (InA.InB)

• Counting ranges: h; min; s; h.min.s

• With AC power supply: sensor supply

voltage 24 V DC ±15 %/100 mA

2. Inputs

INP A

Start input (depending on the input mode chosen)

INP B

Time meter Start/Stop or gate input (depending

on the input mode chosen)

RESET

Dynamic RESET input. Linked in parallel to the

red RESET key. Resets the counter to zero. Can

be adjusted individually for Counter 1 and

Counter 2.

3. Selection of the displayed value

Pressing the right key allows switching between

the display of time meter 1 and the display of

time meter 2. Press the key briefly to display for 2

seconds the current function (“time1” or “time2”).

If, during this period of time, the right key is

pressed a second time, the device switches to

the current function and displays a confirmation

(“time1” or “time2”) for 2 seconds. Then, the

value of the selected function is displayed.

4. Programming routine

The programmable parameters of the device are

described below, in the order in which they can

be set. The device is fully programmed after one

pass of the routine.

The first values stated correspond to the factory

settings

4.1 Polarity of the inputs

npn: switching for 0 V

pnp: switching for +UB

4.2 Switching on the 30 Hz filter (INP A, INP B)

30 Hz filter off (fmax)

Start/Stop inputs not

damped

30 Hz filter on

Start/Stop inputs damped

for use with mechanical

switches

Time unit: seconds (accu-

racy depending on posi-

tion of the decimal point*)

Time unit: minutes (accu-

racy depending on posi-

tion of the decimal point*)

Time unit: hours (accura-

cy depending on position

of the decimal point*)

Time units:

Hours:Minutes:Seconds

(decimal point setting is

ignored)

4.4 Operating mode

*0, 0.1, 0.01, 0.001 means: time measurement in

0, 0.1, 0.01, 0.001 time units

4.5 Decimal point

The decimal point defines

the resolution of the pro-

grammed time unit.

0.0 1/10 (0,1)

0.00 1/100 (0,01)

0.000 1/1000 (0,001)

4.7 RESET mode (time meter 2)

manual reset via the red

RESET key and electrical

reset via the RESET input

no reset (red RESET key

and RESET input locked)

only electrical reset via the

RESET input

only manual reset via the

red RESET key

only electrical reset via the

RESET input

only manual reset via the

red RESET key

4.6 RESET mode (time meter 1)

manual reset via the red

RESET key and electrical

reset via the RESET input

no reset (red RESET key

and RESET input locked)

Start/Stop via Inp B.

Counting while Inp B

(Gate) not active or open

Start/Stop via Inp B.

Counting while Inp B (Gate)

active (High level with

pnp; Low level with npn)

Count

Start/Stop via

INP B

(LOW-HIGH edge with

pnp; HIGH-LOW edge

with npn). Every active

edge changes the counter

status.

Count start via INP A,

stop via INP B. (LOW-

HIGH edge with pnp;

HIGH-LOW edge with

npn)

4.3 Input mode (time meter)

Autres manuels pour CODIX 54U

Table des matières

Autres manuels Kübler Caisse enregistreuse

Kübler

Kübler 716 Series Manuel utilisateur

Kübler

Kübler Codix 141 Manuel utilisateur

Kübler

Kübler CODIX 54U Manuel utilisateur

Kübler

Kübler CODIX 541 Manuel utilisateur

Kübler

Kübler Codix 140 Manuel utilisateur

Kübler

Kübler 521 Manuel utilisateur

Kübler

Kübler CODIX 521 Manuel utilisateur

Kübler

Kübler CODIX 541 Manuel utilisateur

Kübler

Kübler CODIX 541 Manuel utilisateur

Kübler

Kübler 901 Manuel utilisateur

Kübler

Kübler codix 130 Manuel utilisateur

Kübler

Kübler 57 Series Manuel utilisateur

Kübler

Kübler CODIX 520 Manuel utilisateur

Kübler

Kübler 560 Manuel utilisateur

Kübler

Kübler CODIX 540 Manuel utilisateur

Kübler

Kübler codix 132 Manuel utilisateur

Kübler

Kübler MWE40 Manuel utilisateur

Kübler

Kübler Codix 923 Manuel utilisateur

Kübler

Kübler CODIX 520 Manuel utilisateur

Kübler

Kübler codix 130 Manuel d'instructions

Kübler

Kübler codix 130 Manuel utilisateur

Kübler

Kübler CODIX 924 Manuel utilisateur

Kübler

Kübler CODIX 52T Manuel utilisateur

Kübler

Kübler CODIX 924-4 Manuel utilisateur

Manuels Caisse enregistreuse populaires d'autres marques

Omron

Omron H7CL Series Manuel utilisateur

FAAC

FAAC XTR B Manuel utilisateur

Olympia

Olympia NC-350A Series Manuel utilisateur

Evco

Evco EV7001 Manuel utilisateur

Record

Record FlowControl Manuel utilisateur

XIA

XIA UltraLo-1800 Manuel utilisateur

Cashmaster

Cashmaster Sigma 105 Manuel utilisateur

Agilent Technologies

Agilent Technologies 53151A Manuel utilisateur

Cashmaster

Cashmaster Sigma 105 Manuel utilisateur

Tellermate

Tellermate TY Manuel d'utilisation et d'entretien

HYOSUNG

HYOSUNG MX-4000W Manuel utilisateur

Cashmaster

Cashmaster Sigma 105 Manuel utilisateur

CCE

CCE 3200 Manuel utilisateur

HP 53150A Series Mode d'emploi

HYOSUNG

HYOSUNG 1800CE Manuel utilisateur

MZ electronic

MZ electronic EV-040 Manuel utilisateur

Delfield

Delfield Shelleysteel SCFM-50 Manuel utilisateur

TSI Instruments

TSI Instruments AEROTRAK+ 7201 Manuel utilisateur