Juniper QFX3100 Manuel utilisateur

Quick Start Guide

QFX3100

IN THIS GUIDE

Step 1: Begin | 1

Step 2: Up and Running | 5

Step 3: Keep Going | 6

Step 1: Begin

IN THIS SECTION

Mount the QFX3100 | 2

Connect Power to the QFX3100 | 3

Connect the QFabric System Control Plane and Data Plane | 4

To install and configure a Juniper Networks QFX3100 Director device, you need:

•One pair of adjustable rear mounting brackets (provided)

•Screws to attach the mounting brackets to the chassis (provided)

•Phillips (+) screwdriver, number 2, to remove and tighten screws

•12 screws to secure the chassis and mounting brackets to the rack (not provided)

•Screwdriver appropriate for your rack mounting screws (not provided)

•Two power cords with plugs appropriate for your geographical location (provided)

Mount the QFX3100

These instructions describe mounting the device in a four-post 19-in. rack or cabinet.

1. Place the rack in its permanent location, allowing adequate clearance for airflow and maintenance, and secure it to the

building structure.

NOTE: If you are mounting multiple units in the rack, mount the heaviest unit at the bottom of the rack, and

mount the others from bottom to top in order of decreasing weight.

2. Measure the distance between the front and rear rack rails. Using this measurement, attach the adjustable rear mounting

brackets to both sides of the chassis using the provided screws. These mounting brackets support the rear of the

chassis and must be installed.

g050061

3. Flip open the hinged rack-mounting plates at the end of the brackets before positioning the device between the rack

rails.

NOTE: The device weighs approximately 41.2 lb (18.7 kg). Installing the QFX3100 Director device in a rack

or cabinet requires one person to lift it and a second person to secure it to the rack.

4. Have one person grasp both sides of the device, lift it, and position it in the rack, aligning the front bracket holes with

the holes in the rack.

5. Have a second person install a mounting screw—and cage nut and washer if your rack requires them—in each of the

four bracket holes to secure the device to the front rack rails.

6. While still supporting the chassis, have the second person install a mounting screw—and cage nut and washer if your

rack requires them—in each of the three bracket holes on the adjustable rear mounting brackets to secure the device

to the rear rack rails.

Connect Power to the QFX3100

1. Insert the coupler end of the power cord into the AC power cord inlet on the AC power supply faceplate.

2. If the AC power source outlet has a power switch, set it to the OFF (O) position.

3. Insert the power cord plug into an AC power source outlet.

4. If the AC power source outlet has a power switch, set it to the ON (|) position.

5. Repeat Step 1 through Step 4 for the second AC power supply.

6. To power on the device, set the power switch on the back of the QFX3100 Director device to the ON (I) position. The

power switch is located next to the power supplies.

Connect the QFabric System Control Plane and Data Plane

The initial connection and configuration of your Juniper Networks QFX3000 QFabric System are beyond the scope of

this quick start. The following steps provide an overview of the tasks required to complete the setup process for your

QFabric system. The port connections are specific and cannot be described fully here. For a detailed description of the

port connections, see the deployment guide for your QFabric system at

https://www.juniper.net/documentation/en_US/junos/information-products/pathway-pages/qfx-series/qfabric-deployment.html.

g050068

USB

Management

Ethernet port

Console

port

Ports 1-4 Ports 5-8

1. Install a second QFX3100 Director device. Together the two Director devices form a Director group. The second

Director device provides redundancy for the QFabric system control plane and management network.

2. Connect network module ports on the first QFX3100 Director device to the second Director device. See the QFabric

system control plane example in the deployment guide for your QFabric system at

https://www.juniper.net/documentation/en_US/junos/information-products/pathway-pages/qfx-series/qfabric-deployment.html.

3. Using the connection diagram in the deployment guide, connect network module ports on the QFX3100 Director

device to Juniper Networks control plane Ethernet switches. This connects the Director device to the control plane

for your QFabric system.

4. Connect your Interconnect devices and Node devices to the control plane Ethernet switches.

5. Connect the QSFP+ uplink ports on each Node device to the 40-Gigabit Ethernet QSFP+ ports on your Interconnect

devices. Connect the 10-Gigabit Ethernet or Fibre Channel ports on the Node devices to servers or storage devices.

These connections form the data plane for your QFabric system.

6. Connect your management network to the management Ethernet port on both Director devices.The management

Ethernet (MGMT) port is located on the left side of the front panel of the Director device.

Step 2: Up and Running

IN THIS SECTION

Set Parameter Values | 5

Perform the Initial Configuration | 5

Set Parameter Values

After you power on the QFX Series device, you must perform the initial setup of the QFX3100 Director group.

Before you begin, set the following parameter values in the terminal emulator software on your laptop or PC:

•Baud Rate—9600

•Flow Control—None

•Data—8

•Parity—None

•Stop Bits—1

•DCD State—Disregard

Perform the Initial Configuration

To connect and configure the Director group from the console:

1. Connect the console port of one Director device in the group to a laptop or PC using the provided RJ-45 cable and

RJ-45 to DB-9 serial port adapter. The console (CONSOLE) port is located on the front panel of the Director device.

2. Insert the USB flash drive containing the range of reserved MAC addresses, software serial number, and platform type

information for your QFabric system into the USB port on the Director device.

NOTE: If the USB flash drive is not provided with your Director device, the initial setup script will prompt you for this

information, which is obtained through the License Management System at

https://www.juniper.net/documentation/en_US/release-independent/licensing/information-products/pathway-pages/licensing.html.

3. Log in as root. If the software booted before you connected to the console port, you might need to press the Enter

key for the prompt to appear.

NOTE: The login prompt is either dg0 login or dg1 login depending on the Director device to which you

connected your cable.

4. The Director group initial setup script prompts you to configure the QFabric system with the following information:

•IP addresses and a default gateway IP address for your QFabric system default partition

•IP addresses for your Director group device management ports

•A root password for your Director group, and a root password for the QFabric components such as the Node devices,

Interconnect devices, and infrastructure

1. Once you connect your management network to the management Ethernet ports on your Director devices and you

run the initial setup script on your Director group, log out of your console connection to the Director group.

2. From a management station on your management network, log in to the QFabric system default partition (using the

IP addresses you specified in the Director group installation script). For detailed information about these procedures,

see the deployment guide for your QFabric system at

https://www.juniper.net/documentation/en_US/junos/information-products/pathway-pages/qfx-series/qfabric-deployment.html.

Step 3: Keep Going

IN THIS SECTION

Safety Warnings Summary | 7

Power Cable Warning (Japanese) | 7

Contacting Juniper Networks | 8

See the complete QFX3100 documentation at

https://www.juniper.net/documentation/en_US/release-independent/junos/topics/concept/qfxctrl-hardware-overview.html.

Safety Warnings Summary

This is a summary of safety warnings. For a complete list of warnings, including translations, see the QFX3100 documentation

https://www.juniper.net/documentation/en_US/release-independent/junos/topics/concept/qfxctrl-hardware-overview.html.

WARNING: Failure to observe these safety warnings can result in personal injury or death.

•Permit only trained and qualified personnel to install or replace device components.

•Perform only the procedures described here and in the QFX Series documentation. Other services must be performed

only by authorized service personnel.

•Before installing the device, read the planning instructions in the QFX Series documentation to make sure that the site

meets power, environmental, and clearance requirements for the device.

•Before connecting the device to a power source, read the installation instructions in the QFX3100 Director device

documentation.

•z A fully loaded QFX3100 Director device weighs approximately 41.2 lb (18.73 kg). Manually installing the device in a

rack or cabinet requires one person to lift the device and a second person to install the mounting screws. To prevent

injury, keep your back straight and lift with your legs, not your back.

•If the rack or cabinet has stabilizing devices, install them in the rack before mounting or servicing the device in the rack

or cabinet.

•Before installing or after removing an electrical component, always place it component-side up on a flat antistatic mat

or in an antistatic bag.

•Do not work on the device or connect or disconnect cables during electrical storms.

•Before working on equipment that is connected to power lines, remove jewelry, including rings, necklaces, and watches.

Metal objects heat up when connected to power and ground and can cause serious burns or become welded to the

terminals.

Power Cable Warning (Japanese)

The attached power cable is only for this product. Do not use this cable for another product.

g040300

Contacting Juniper Networks

For technical support, see:

http://www.juniper.net/support/requesting-support.html

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in the

United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the

property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper

Table des matières

Autres manuels Juniper Changer

Juniper

Juniper EX4550 Instructions d'installation

Juniper

Juniper EX4100 Manuel utilisateur

Juniper

Juniper EX2200 Series Mode d’emploi

Juniper

Juniper PTX Series Instructions d'installation

Juniper

Juniper EX8200 Series Guide de démarrage rapide

Juniper

Juniper EX4300 Instructions d'installation

Juniper

Juniper OCX1100-48SX Manuel utilisateur

Juniper

Juniper EX8216 Instructions d'installation

Juniper

Juniper Day One+ Instructions d'installation

Juniper

Juniper EX2300 Series Manuel utilisateur

Juniper

Juniper EX3200 Series Manuel utilisateur

Juniper

Juniper EX4500 Series Manuel utilisateur

Juniper

Juniper EX3200 Series Guide de démarrage rapide

Juniper

Juniper EX2500 Manuel utilisateur

Juniper

Juniper EX Series Manuel utilisateur

Juniper

Juniper EX8200 Series Manuel utilisateur

Juniper

Juniper EX3300 Manuel utilisateur

Juniper

Juniper EX2500 Instructions d'installation

Juniper

Juniper EX2200 Series Instructions d'installation

Juniper

Juniper QFX5220 Instructions d'installation

Juniper

Juniper EX Series Manuel utilisateur

Juniper

Juniper QFX10008 Manuel utilisateur

Juniper

Juniper QFX5100-96S Manuel utilisateur

Juniper

Juniper QFX5110 Instructions d'installation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur