Juniper EX4300 Manuel utilisateur

Day One+

EX4300

IN THIS GUIDE

Step 1: Begin | 1

Step 2: Up and Running | 6

Step 3: Keep Going | 9

Step 1: Begin

IN THIS SECTION

Meet the EX4300 Line of Ethernet Switches | 1

Install the EX4300 | 2

Power On | 5

Meet the EX4300 Line of Ethernet Switches

The Juniper Networks®EX4300 Ethernet Switches are fixed-configuration platforms that can be deployed as standalone

systems or as part of a Virtual Chassis switching architecture. The EX4300 switches are available in 24-port, 32-port, and

48-port models, with or without PoE+, with AC or DC power supplies, and with different airflow directions. EX4300

switches also provide uplink ports and a slot for installing an optional uplink module.

PoE/PoE+ Ports10/100/1000BASE-T PortsModel

024EX4300-24T

2424EX4300-24P

PoE/PoE+ Ports10/100/1000BASE-T PortsModel

048EX4300-48T

4848EX4300-48P

4824

(plus 24 100/1000/2500/5000/10000BASE-T

ports)

EX4300-48MP

032 100/1000BASE-X portsEX4300-32F

In this guide, we show you how to install an AC-powered EX4300 switch with the fan modules and power supplies

preinstalled. If you need instructions for installing fans, power supplies, and optional uplink modules, see the EX4300

Switch Hardware Guide.

Install the EX4300

IN THIS SECTION

What’s in the Box? | 3

What Else Do I Need? | 3

Install the EX4300 Switch in a Two-Post Rack | 3

You can install the EX4300 switch on a table or desktop, on a wall, or in a two-post or four-post rack. The mounting kit

that ships in the box has the brackets you need to install the EX4300 switch in a two-post rack. We’ll walk you through

how to do that.

NOTE: If you want to install the switch on the wall or in a four-post rack, you’ll need to order separate mounting

kits. The four-post rack mount kit also has brackets for mounting the EX4300 switch in a recessed position in

the rack.

What’s in the Box?

•EX4300 switch

•An AC power cord appropriate for your geographical location

•Two mounting brackets and eight mounting screws

•An Ethernet cable with RJ-45 connectors attached and an RJ-45 to DB-9 serial port adapter

What Else Do I Need?

You’ll need to provide the following:

•Four rack mount screws to secure the chassis to the rack

•A number two Phillips (+) screwdriver

•An electrostatic discharge (ESD) grounding strap

•A management host such as a laptop or desktop PC

•A serial-to-USB adapter (if your laptop or desktop PC doesn’t have a serial port)

•Someone to help you secure the switch to the rack

Install the EX4300 Switch in a Two-Post Rack

1. Review General Safety Guidelines and Warnings

2. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other end to a site ESD

point.

3. Attach the mounting brackets to the sides of the EX4300 switch using the eight screws and a screwdriver.

You’ll notice there are three locations on the side panel where you can attach the mounting brackets: front, center,

and rear. Attach the mounting brackets to the location that best suits where you want the EX4300 switch to sit in the

rack.

g021433

g022543

g022544

4. Lift the EX4300 switch and position it in the rack. Line up the bottom hole in each mounting bracket with a hole in

each rack rail, making sure the EX4300 switch is level.

g020094

Mounting rack

Mounting bracket

5. While you’re holding the EX4300 switch in place, have someone insert and tighten the rack mount screws to secure

the mounting brackets to the rack rails. Make sure to tighten the screws in the two bottom holes first and then tighten

the screws in the two top holes next.

6. Check that the mounting brackets on each side of the rack are level.

Power On

Now you’re ready to connect the EX4300 switch to a dedicated AC power source. The switch comes with the AC power

cord for your geographic location.

Here’s how to connect the EX4300 switch to AC power:

1. Wrap and fasten one end of an ESD wrist strap around your bare wrist, and connect the other end of the strap to the

ESD point on the switch.

2. On the rear panel, connect the retainer clip and power cord to the AC power socket (see Figure 1 and Figure 2):

a. Push the end of the retainer strip into the hole next to the AC power socket until it snaps into place.

b. Press the small tab on the retainer strip to loosen the loop.

c. Slide the loop until you have enough space to insert the power cord coupler into the AC power socket.

d. Plug in the power cord to the power socket on the switch.

e. Slide the loop toward the power supply until it is snug against the base of the coupler.

f. Press the tab on the loop and draw out the loop into a tight circle.

Figure 1: Connecting AC Power to an EX4300 Switch (Except the EX4300-48MP)

Figure 2: Connecting Power to an EX4300-48MP Switch

g022468

3. If the AC power source outlet has a power switch, turn it off.

4. Plug in the AC power cord to the AC power source outlet.

5. If the AC power source outlet has a power switch, turn it on.

6. Check to see that the IN OK and the OUT OK LEDs on each power supply are lit green.

If the OUT OK LED is lit amber, turn off the AC power source outlet or unplug the switch. You’ll need to replace the

power supply. See Removing an AC Power Supply from an EX4300 System.

Step 2: Up and Running

IN THIS SECTION

Plug and Play | 7

Customize the Basic Configuration | 7

Now that the EX4300 switch is powered on, let’s do some initial configuration to get the switch up and running on your

network. It’s simple to provision and manage the EX4300 switch and other devices on your network. Choose the

configuration tool that’s right for you:

•Juniper Mist. To use Mist, you’ll need an account on the Mist Cloud Platform. See Overview of Connecting Mist Access

Points and Juniper EX Series Switches.

•Juniper Networks Contrail Service Orchestration (CSO). To use CSO, you’ll need an authentication code. See SD-WAN

Deployment Overview in the Contrail Service Orchestration (CSO) Deployment Guide.

•CLI commands

Plug and Play

The EX4300 switches already have factory-default settings configured right out of the box to make them plug-and-play

devices. The default settings are stored in a configuration file that:

•Sets values for system parameters such as syslog and commit

•Configures Ethernet switching on all interfaces

•Enables IGMP snooping

•Enables the LLDP and RSTP protocols

These settings load as soon as you power on the EX4300 switch. If you want to see what’s in the factory-default

configuration file for your EX4300 switch, see EX4300 Switch Default Configuration.

Customize the Basic Configuration

You can easily customize the basic configuration using the EZSetup wizard. When you commit changes in the EZSetup

wizard, a new configuration file is created. This becomes the active configuration. You can always revert to the

factory-default configuration whenever you want.

NOTE: To run the EZSetup wizard, the EX4300 switch must have the factory-default configuration as the active

configuration. If you have configured anything on the switch and want to run EZSetup, you’ll need to revert to

the factory-default configuration. See Reverting to the Default Factory Configuration for the EX Series Switch.

Have these values handy before you begin configuring custom settings for the switch:

•Hostname

•Root authentication password

•Management port IP address

•Default gateway IP address

•(Optional) SNMP read community, location, and contact information

1. Verify that the serial port settings for your laptop or desktop PC are set to the default:

•Baud rate—9600

•Flow control—None

•Data—8

•Parity—None

•Stop bits—1

•DCD state—Disregard

2. Connect the console port on the EX4300 switch to a laptop or desktop PC using the Ethernet cable and the RJ-45 to

DB-9 serial port adapter that came in the box with the switch.

NOTE: If your laptop or desktop PC doesn't have a serial port, use a serial-to-USB adapter (not provided).

3. At the Junos OS login prompt, type root to log in.

4. Type ezsetup to initiate the EZSetup wizard.

5. (Optional) Type the system hostname.

6. Type the new root password that you want to use for the EX4300 switch. Reenter the password when prompted.

7. Type yes to enable Telnet service.

8. Type yes to enable SSH service.

NOTE: You can’t log in as the root user when Telnet is enabled for the MGMT port. You can only log in as

the root user through SSH.

9. Choose in-band management [Option 1]. This is the default.

10. Choose Use VLAN “default” for management [Option 1]. When you use the Default VLAN, all devices you connect to

the switch will be placed into this VLAN. They can begin transmitting traffic on the network without further switch

configuration.

11. Type the management port IP address.

12. Type the submask.

13. Type the gateway IP address.

14. (Optional) Configure SNMP settings and the time zone.

15. When the configured parameters are shown on the screen, type yes to commit the new configuration. This becomes

the active configuration for the EX4300 switch.

You can now log in to the EX4300 switch with the CLI and continue customizing the configuration.

Step 3: Keep Going

Congratulations! Now that you’ve done the initial configuration, your EX4300 switch is ready to use.

Here are some things you can do next:

ThenIf you want to

See Activate Junos OS Licenses in the

Juniper Licensing Guide

Download, activate, and manage your software licenses to unlock

additional features for your EX series switch

Visit EX4300 Documentation in the Juniper

Networks TechLibrary

See all documentation available for the EX4300 switch

Browse through the EX4300 Switch

Hardware Guide

Find more in-depth information about installing and configuring the

EX4300 switch

See Installing Software on EX Series

Switches

Manage software upgrades on your EX Series switch

Visit the Security Design CenterSee, automate, and protect your network with Juniper Security

See the Junos OS Release NotesStay up-to-date about new and changed features and known and resolved

issues

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in the

United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the

property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper

Autres manuels pour EX4300

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Juniper Changer

Juniper

Juniper QFX5220-32CD Manuel utilisateur

Juniper

Juniper EX2200 Series Mode d’emploi

Juniper

Juniper EX3300 Instructions d'installation

Juniper

Juniper QFX5220-128C Manuel utilisateur

Juniper

Juniper EX4200 Series Instructions d'installation

Juniper

Juniper EX Series Manuel utilisateur

Juniper

Juniper QFX3100 Manuel utilisateur

Juniper

Juniper EX4500-40F-FB Manuel utilisateur

Juniper

Juniper QFX5120 Series Instructions d'installation

Juniper

Juniper EX3200 Series Guide de démarrage rapide

Juniper

Juniper EX Series Mode d’emploi

Juniper

Juniper EX4500 Series Instructions d'installation

Juniper

Juniper QFX10016 Manuel utilisateur

Juniper

Juniper EX 3200 48T Manuel utilisateur

Juniper

Juniper EX4200 Series Instructions d'installation

Juniper

Juniper QFX3600 Manuel utilisateur

Juniper

Juniper QFX5200-48Y Manuel utilisateur

Juniper

Juniper EX3200 Series Manuel utilisateur

Juniper

Juniper EX8200 Series Guide de démarrage rapide

Juniper

Juniper Day One+ Instructions d'installation

Juniper

Juniper EX8208 Instructions d'installation

Juniper

Juniper QFX3600 Manuel de l'opérateur

Juniper

Juniper OCX1100-48SX Manuel utilisateur

Juniper

Juniper QFX5230-64CD Instructions d'installation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur