Juniper EX 3200 Manuel utilisateur
Connecting DC Power to an EX 3200 or EX 4200 Switch
The power supply in an EX 3200 or EX 4200 switch is a hot-removable and
hot-insertable field-replaceable unit (FRU) located on the rear panel.
Figure 1: DC Power Supply in EX 3200 and EX 4200 Switches
LED-B
LED-A
Terminal blockLocking lever
LEDs
Handle Fan exhaust
A +
B +
A-
B-
g020202
WARNING: DC-powered EX 3200 and EX 4200 switches are intended for installation
only in a restricted access location.
Ensure that you have the following parts and tools available to connect DC power to
an EX 3200 or EX 4200 switch:
■Electrostatic discharge (ESD) grounding strap
■DC power source cables (12–14 AWG) with ring lug (Molex 190700067 or
equivalent) (not provided)
■Phillips (+) screwdriver, number 2
Before you begin connecting DC power to an EX 3200 or EX 4200 switch:
■Ensure that you have taken the necessary precautions to prevent ESD damage
(see Prevention of Electrostatic Discharge Damage on EX-series Switches).
■Ensure that you have connected the switch chassis to earth ground.
CAUTION: Before you connect power to the switch, a licensed electrician must attach
a cable lug to the grounding and power cables that you supply. A cable with an
incorrectly attached lug can damage the switch (for example, by causing a short
circuit).
To meet safety and electromagnetic interference (EMI) requirements and to ensure
proper operation, you must connect EX 3200 and EX 4200 switches to earth ground
before you connect them to power. For installations that require a separate grounding
conductor to the chassis, use the protective earthing terminal on the switch chassis
Connecting DC Power to an EX 3200 or EX 4200 Switch ■1
to connect to the earth ground. For instructions on connecting earth ground, see
Connecting Earth Ground to an EX-series Switch.
■Install the power supply in the chassis. For instructions on installing a power
supply in an EX 3200 or EX 4200 switch, see Installing a Power Supply in an EX
3200 or EX 4200 Switch.
To connect DC power to an EX 3200 or EX 4200 switch:
1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to the ESD point on the chassis.
2. Ensure that the power supplies are fully inserted in the chassis and the screws
on their faceplates are tightened.
3. Ensure that the input circuit breaker is open so that the voltage across the DC
power source cable leads is 0 V and that the cable leads will not become active
while you are connecting DC power.
NOTE: The DC power supply in EX 3200 and EX 4200 switches has four terminals
labeled A+, A–, B+, and B–(see Figure 1 on page 1) for connecting DC power
source cables labeled positive (+) and negative (–). The DC power supplies for EX
3200 and EX 4200 switches are shipped with jumpers from A+ input to B+ input
tied together and jumpers from A–input to B–input tied together.
NOTE: The A+ and B+ terminals are referred to as +RTN and A–and B–terminals
are referred to as –48 V in DC Power Wiring Sequence Warning for EX 3200 and EX
4200 Switches and DC Power Electrical Safety Guidelines for EX 3200 and EX 4200
Switches.
4. Remove the screw securing the terminal block cover using the
Phillips (+) screwdriver, number 2 and remove the terminal block cover (see
Figure 2 on page 3). Save the screw.
2■Connecting DC Power to an EX 3200 or EX 4200 Switch
Figure 2: Removing the Terminal Block Cover in a DC Power Supply in EX 3200 and
EX 4200 Switches
LED-B
LED-A
A+
B
g020205
5. Remove the screws on the terminals using the Phillips (+) screwdriver, number 2.
Save the screws.
WARNING: Ensure that the power cables do not block access to switch components
or drape where people can trip on them.
6. Connect the power supplies to the power sources. Secure power source cables
to the power supplies by screwing the ring lug attached to the cable to the
appropriate terminal by using the screw from the terminal (see
Figure 3 on page 4).
■To connect a power supply to a power source:
a. Leave the jumpers on the power supply terminals in place.
b. Secure the ring lug of the positive (+) DC power source cable to the A+
or B+ terminal on the DC power supply.
c. Secure the ring lug of the negative (–) DC power source cable to the A–
or B–terminal on the DC power supply.
d. Tighten the screws on the power supply terminals until snug using the
Phillips (+) screwdriver, number 2. Do not overtighten—apply between
8 lb-in. (0.9 Nm) and 9 lb-in. (1.02 Nm) of torque to the screws.
If you have a second installed power supply, connect it in the same way you
did the first.
■To connect one power supply to two power sources:
a. Remove the jumpers on the power supply terminal block.
b. Secure the ring lug of the positive (+) DC power source cable from the
first DC power source to the A+ terminal on the first DC power supply.
Connecting DC Power to an EX 3200 or EX 4200 Switch ■3
c. Secure the ring lug of the negative (–) DC power source cable from the
first DC power source to the A–terminal on the first DC power supply.
d. Secure the ring lug of the positive (+) DC power source cable from the
second DC power source to the A+ terminal on the second DC power
supply.
e. Secure the ring lug of the negative (–) DC power source cable from the
second DC power source to the A–terminal on the second DC power
supply.
f. Tighten the screws on the power supply terminals on both the power
supplies until snug using the Phillips (+) screwdriver, number 2. Do not
overtighten—apply between 8 lb-in. (0.9 Nm) and 9 lb-in. (1.02 Nm) of
torque to the screws.
Figure 3: Securing Ring Lugs to the Terminals on the DC Power Supply in EX 3200
and EX 4200 Switches
A +
B +
A-
B-
LED-B
LED-A
g020203
7. Replace the terminal block cover and secure it using the screw. Use the
Phillips (+) screwdriver, number 2 to tighten the screw.
8. Close the input circuit breaker.
9. Verify that the LEDs on the power supply are lit green and are on steadily.
DC Power Supply LEDs in EX 3200 and EX 4200 Switches describes the LEDs on the
DC power supplies in EX 3200 and EX 4200 switches.
Related Topics ■Connecting and Configuring the EX-series Switch (CLI Procedure)
■Connecting and Configuring the EX-series Switch (J-Web Procedure)
■Power Supply in EX 3200 and EX 4200 Switches
■Connecting AC Power to an EX 3200 or EX 4200 Switch
4■Connecting DC Power to an EX 3200 or EX 4200 Switch
Autres manuels pour EX 3200
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Juniper Changer
Juniper
Juniper QFX5100 Instructions d'installation
Juniper
Juniper EX8200 Series Manuel utilisateur
Juniper
Juniper EX2200 Series Manuel utilisateur
Juniper
Juniper QFX3000-G QFabric Guide de référence rapide
Juniper
Juniper EX Series Manuel utilisateur
Juniper
Juniper EX8208 Manuel utilisateur
Juniper
Juniper OCX1100-48SX Manuel utilisateur
Juniper
Juniper EX4600 Manuel utilisateur
Juniper
Juniper NETWORK AND SECURITY MANAGER NSM3000 - REV... Manuel utilisateur
Juniper
Juniper EX8200 Series Manuel utilisateur
Juniper
Juniper EX8200 Series Mode d’emploi
Juniper
Juniper QFX5200-48Y Manuel utilisateur
Juniper
Juniper EX3200 Series Instructions d'installation
Juniper
Juniper QFX10008 Instructions d'installation
Juniper
Juniper QFX5220-128C Manuel utilisateur
Juniper
Juniper EX3300 Manuel utilisateur
Juniper
Juniper EX4650 Series Instructions d'installation
Juniper
Juniper EX8208 Manuel utilisateur
Juniper
Juniper EX3200 Series Mode d’emploi
Juniper
Juniper QFX5230-64CD Instructions d'installation
