Juniper EX Series Mode d’emploi

Installing a Power Supply in an EX-series Switch

The power supply in EX 3200 and EX 4200 switches is a hot-removable and

hot-insertable field-replaceable unit (FRU): you can remove and replace it without

powering off the switch or disrupting switch functions.

Ensure you have the following parts and tools available to install a power supply in

an EX 3200 or EX 4200 switch chassis:

■Electrostatic discharge (ESD) grounding strap

■Phillips (+) screwdriver, number 2

Before you begin installing a power supply in an EX 3200 or EX 4200 switch, ensure

that you have taken the necessary precautions to prevent ESD damage (see Preventing

Electrostatic Discharge Damage).

To install a power supply in an EX 3200 or EX 4200 switch (see Figure 1 on page 2):

1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to the ESD point on the chassis.

2. Taking care not to touch power supply components, pins, leads, or solder

connections, remove the power supply from its bag.

3. Loosen the locking lever screw on the left front of the power supply by using the

Phillips (+) screwdriver, number 2.

4. Push down on the locking lever until it is in its lowest position.

5. Using both hands, place the power supply in the power supply slot on the rear

panel of the switch and slide it in until it is fully seated.

NOTE: The handle on the 320 W AC power supply is at the bottom of the power

supply faceplate, while the handle on the 600 W and the 930 W AC power supplies

is at the top of the faceplate. The handle on the 190 W DC power supply runs across

the faceplate.

6. Push the locking lever up to its highest position (this action might pull the power

supply in).

7. Tighten the locking lever screw by using the Phillips (+) screwdriver, number 2.

Installing a Power Supply in an EX-series Switch ■1

Figure 1: Installing a Power Supply in an EX 3200 or EX 4200 Switch

NOTE: Each power supply must be connected to a dedicated power source outlet.

NOTE: If you have a Juniper J-Care service contract, register any addition, change,

or upgrade of hardware components at

https://www.juniper.net/customers/csc/management/updateinstallbase.jsp. Failure to do so

can result in significant delays if you need replacement parts. This note applies if

you change the type of power supply or add a new type of uplink module. It does

not apply if you replace these components with the same type of component.

Related Topics ■Removing a Power Supply from an EX-series Switch

■Installing and Removing EX-series Switch Hardware Components

■Power Supply in EX-series Switches

■Field-Replaceable Units in EX-series Switches

■AC Power, Connection, and Power Cord Specifications

■EX 3200 Switch—Rear-Panel Description

■EX 4200 Switch—Rear-Panel Description

2■Installing a Power Supply in an EX-series Switch

Autres manuels pour EX Series

15

Ce manuel convient aux modèles suivants

2

Table des matières

Autres manuels Juniper Changer

Juniper

Juniper EX3300 Manuel utilisateur

Juniper

Juniper QFX5210 Manuel utilisateur

Juniper

Juniper EX3300 Manuel utilisateur

Juniper

Juniper EX4200 Series Instructions d'utilisation et de sécurité

Juniper

Juniper QFX10008 Instructions d'installation

Juniper

Juniper EX Series Manuel utilisateur

Juniper

Juniper EX4600 Instructions d'installation

Juniper

Juniper EX4500 Series Instructions d'installation

Juniper

Juniper EX9214 Manuel utilisateur

Juniper

Juniper NETWORK AND SECURITY MANAGER NSM3000 - REV... Manuel utilisateur

Juniper

Juniper QFX5100 Instructions d'installation

Juniper

Juniper QFX Series Instructions d'installation

Juniper

Juniper EX2300 Series Manuel utilisateur

Juniper

Juniper EX8200 Series Mode d’emploi

Juniper

Juniper QFX5130-32CD Instructions d'installation

Juniper

Juniper EX8200 Series Mode d’emploi

Juniper

Juniper EX 4200 24F Manuel utilisateur

Juniper

Juniper QFX5120 Series Manuel utilisateur

Juniper

Juniper EX3200 Series Mode d’emploi

Juniper

Juniper QFX5220-32CD Manuel utilisateur

Juniper

Juniper EX4550 Instructions d'installation

Juniper

Juniper QFX5100 Instructions d'installation

Juniper

Juniper QFX5130 Manuel utilisateur

Juniper

Juniper QFX5200 Instructions d'installation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur