Jbc TRA245-B Manuel utilisateur

TRA

Automatic Soldering Iron

for Robot

INSTRUCTION MANUAL

Packing List

Automatic Soldering Iron for Robot ................................................................................................... 1 unit

Manual ......................................................................................................................................................... 1 unit

Ref. 0027874

Either Ref. TRA245-B or Ref. TRA470-B is included.

This manual corresponds to the following references:

- TRA245-B works with R245 cartridges

- TRA470-B works with R470 cartridges

SFR-B

GSFR

TRA

CLR

EXTRACCIÓN

22220

EXTRACCIÓN

26842

26843

EXTRACCIÓN

26846

26847

26848

EXTRACCIÓN

26844

VERMELL

NEGRE GROC

VERMELL

BLAU

VERMELL

BLAU

VERD

VERMELL

BLAU

VERD

VERMELL

NEGRE GROC

VERMELL

BLAU

VERD

Lorem ipsum

SFR-B

GSFR

TRA

CLR

EXTRACCIÓN

22220

EXTRACCIÓN

26842

26843

EXTRACCIÓN

26846

26847

26848

EXTRACCIÓN

26844

VERMELL

NEGRE GROC

VERMELL

BLAU

VERMELL

BLAU

VERD

VERMELL

BLAU

VERD

VERMELL

NEGRE GROC

VERMELL

BLAU

VERD

Lorem ipsum

SFR-B

GSFR

TRA

CLR

EXTRACCIÓN

22220

EXTRACCIÓN

26842

26843

EXTRACCIÓN

26846

26847

26848

EXTRACCIÓN

26844

VERMELL

NEGRE GROC

VERMELL

BLAU

VERMELL

BLAU

VERD

VERMELL

BLAU

VERD

VERMELL

NEGRE GROC

VERMELL

BLAU

VERD

Lorem ipsum

Solder Feeder

for Robot *

Ref. SFR-B

GSFR Guide Tube*

Automatic

Soldering Iron

for Robot*

Ref. TRA-B

The guide position

can be adjusted in

angle, height and

length

Assembly: GSFR Tube to SFR* and TRA*

1. Assemble SFR and the appropiate GSFR Guide Tube to TRA as described in SFR instructions

manual.

2. Adjust TRA guide position in angle, height and lenght, then tighten the bolt to lock your settings.

3. Adjust TRA angle to its desired position by using the indicated bolt.

4. Adjust TRA guide arm position for your application by using the indicated bolt.

*Not included, sold separately

www.jbctools.com

Connections

Connection

to UCR

Gripper Actuator

Fluid Air

Applicable tubing Ø4mm

Operating pressure 1,5 to 7 bar

20 to 100 psi

A Air tube connection: Close arm to soldering position.

B Air tube connection: Open arm to service position.

C Air tube connection: Close grippers.

D Air tube connection: Open grippers.

Note: JBC recommends bi-stable valves for the grippers to prevent the cartridge from falling out in

case of an emergency stop or power cut.

TRA245-B

Dimensions

www.jbctools.com

TRA470-B

Dimensions

Centering Jig

Instal both, lower and upper centering jigs,

into CSR Cartridge Stand and HA Soldering

Unit as shown.

Adjust the Soldering Head position until the

upper and lower centering jigs are aligned. It

must be possible to move in and out smoothly.

Insert the centering jig completely. Set this

point as the pick-up point position. The

Soldering Head has to move in a vertical line

from this point when inserting or removing

cartridges.

In order to align the CSR to your Soldering Head and set your cartridge pick-up points use JBC´s

Centering Jig.

Lower

Centering Jig

Upper

Centering Jig

HA Soldering

Unit

CSR Cartridge

Stand

www.jbctools.com

Work Place Example

*Not included, sold separately

TRA

CSR

SFR

CLR

UCR

GSFR

Soldering

Irons

Cartridge Range Control Unit Cartridge Stand

R245 R470 UCR245 UCR470 CS2R245 CS2R470

TRA245

TRA470

SFR, GSFR and CLMR are compatible with both R245 and R470 cartridges.

Compatibility

Maintenance

- Before carrying out maintenance, always unplug the tool.

- Use a damp cloth to clean the tool. Alcohol can only be used to clean the metal parts.

- Periodically check that the metal parts of the tool are clean so the control unit can detect the tool

status.

- Periodically check all cable and tube connections.

- Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat transfer to the solder joint.

- Replace any defective or damaged part. Use original JBC spare parts only.

- Repairs should be performed only by a JBC authorized technical service.

- Under normal operating conditions, the air gripper lifespan is 10 million cycles. It is recommended

to replace it at the end of its lifespan.

www.jbctools.com

It is imperative to follow safety guidelines to prevent electric shock,

injury, fire or explosion.

- Do not use the soldering iron for any purpose other than soldering or rework. Incorrect use may

cause fire.

- Do not leave the appliance unattended when it is on.

- Be sure that the power supply is disconnected before changing any spare part.

- The temperature of accessible surfaces may remain high after the unit is turned off.

Handle with care.

- Allow the cartridges to cool down before changing them.

- Heat can cause inflamable products to ignite even when not visible.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

Safety

Notes

Ce manuel convient aux modèles suivants

Table des matières

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel

jbc TRA245-B Manuel utilisateur

Manuels Outils électriques populaires d'autres marques