Jackson Labs LTE-Lite Manuel utilisateur
LTE-Lite(tm) User
Manual
Document: 80200522
Version: 1.4
Date: 25 June, 2020
LTE-Lite User Manual
Copyright © 2013 to 2020 Jackson Labs Technologies, Inc.
© 2020 Jackson Labs Technologies, Inc. i
LTE-Lite User Manual
1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2.1 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2.2 Antenna Lightning Protection . . . . . . . . . . . . . . . . . . . . . 2
1.2.3 Power Connections. . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2.4 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . 2
2 Usage Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Powering Up the Evaluation Board . . . . . . . . . . . . . . . . . . . . . 3
2.1.1 Airflow Warning . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1.2 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.3 USB Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.4 Major connections . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.5 Typical Phase Noise and ADEV Plots . . . . . . . . . . . . . . . . . 6
2.1.6 Evaluation Board Mechanical Dimensions . . . . . . . . . . . . . . . . 8
2.1.7 LTE-Lite SMT Module Mechanical Dimensions . . . . . . . . . . . . . . 9
2.1.8 LTE-Lite Evaluation Board Schematics . . . . . . . . . . . . . . . . . 9
2.2 Connector, Buttons and Switches on the Evaluation Board . . . . . . . . . . . . 11
2.3 LTE-Lite SMT Module usage . . . . . . . . . . . . . . . . . . . . . . . 13
2.3.1 LTE-Lite SMT Module Minimum Required Setup . . . . . . . . . . . . . 13
2.3.2 Using the LTE-Lite SMT Module with external TCXOs . . . . . . . . . . .14
2.3.3 Using the LTE-Lite SMT Module Synthesized Frequency Output . . . . . . .16
2.3.4 Adding a USB output to the LTE-Lite SMT Module for NTP applications . . . .17
2.3.5 SMT Module Power Connection . . . . . . . . . . . . . . . . . . . . 18
2.3.6 SMT Module Antenna Connection . . . . . . . . . . . . . . . . . . .18
2.3.7 1PPS Module outputs . . . . . . . . . . . . . . . . . . . . . . . .18
2.3.8 Synthesized RF Output Frequency. . . . . . . . . . . . . . . . . . .18
2.3.9 System Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.3.10Module Serial IO pins . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.11Module IO Pinout . . . . . . . . . . . . . . . . . . . . . . . . .20
2.4 Connecting a GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . 24
2.5 USB serial connection . . . . . . . . . . . . . . . . . . . . . . . . . .25
2.5.1 Proprietary $PSTI NMEA GPS Status Sentence . . . . . . . . . . . . . 25
2.5.2 JLT Proprietary STATUS Output Sentence . . . . . . . . . . . . . . .25
2.5.2.1 Lock Status Definition . . . . . . . . . . . . . . . . . . . .26
2.5.2.2 Health Status Definition . . . . . . . . . . . . . . . . . . . .26
3 Certification and Warranty . . . . . . . . . . . . . . . . . . . . .29
3.1 Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.1.1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.1.2 Limitation of Warranty. . . . . . . . . . . . . . . . . . . . . . . .29
3.1.3 Exclusive Remedies . . . . . . . . . . . . . . . . . . . . . . . .30
LTE-Lite User Manual
ii © 2020 Jackson Labs Technologies, Inc.
© 2020 Jackson Labs Technologies, Inc. 1
LTE-Lite User Manual
Introduction
1.1 Overview
The LTE-Lite GPSDO is a very low-cost, small SMT Timing and Frequency reference module for
high-volume Small Cell applications. It is intended to provide precise timing and a very low Phase
Noise and jitter frequency reference to RF Transceivers and Base Band processors as typically used
in Small Cell applications. The LTE-Lite is a true GPSDO rather than a Numerically Controlled
Oscillator, using true precision analog disciplining of the high-end Crystal rather than digital
phase-adjustments of a free running low-cost crystal, resulting in many orders of magnitude less jitter
and Phase Noise. The LTE-Lite GPSDO is available as an SMT module, or mounted onto the
LTE-Lite Evaluation Board with easy access to relevant signals via a host of connectors and
switches.
The LTE-Lite GPSDO and LTE-Lite Evaluation Board include a high-performance GPS/QZSS
receiver that can acquire and track up to 65 GPS signals down to a state of the art –165dBm, a 32bit
processor, a low-noise 3V CMOS 10MHz, 19.2MHz, or 20MHz output, two 3.3V CMOS 1PPS
outputs, TTL or USB status and Position-Velocity-and-Time (PVT) interface, precision voltage
references, power filters, and DACs. It generates a low-noise 10/19.2/20MHz signal with typically
better than 1E-09 precision and accuracy (1ppb), better than typ. 135fs jitter (100Hz to 2MHz) and a
1PPS signal with typically better than +/-25ns stability when locked to GPS.
The LTE-Lite GPSDO provides status information on TTL output lines that can directly drive LEDs,
and has two serial output ports for NMEA PVT and Oscillator status output. All configuration of the
LTE-Lite GPSDO is done via pull-down TTL straps with built-in pull-up resistors, so no software
configuration driver is needed on the users’ system. The evaluation kit may be operated and powered
from the built-in USB port, or an optional 5V power supply and both power-sources may be
connected simultaneously. The evaluation kit is supplied with a USB cable and matching wall-wart
power supply, two MMCX to BNC adaptor cables, a GPS antenna, and a quick-start guide. The unit
provides an industry-standard NMEA GPS serial output that is enabled by default and provides
Position/Velocity/Timing (PVT) information, and also provides a UTC-synchronized 1PPS signal on
the USB serial port DCD# pin for NTP applications. The LTE-Lite GPSDO also provides a
NMEA-compatible proprietary status message on a secondary serial port that sends oscillator lock
status as well as health status information to a users’ system.
LTE-Lite User Manual
2© 2020 Jackson Labs Technologies, Inc.
1.2 General Safety Precautions
The following general safety precautions must be observed during all phases of operation of this
instrument. Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design manufacture, and intended use of the instrument. Jackson
Labs Technologies, Inc. assumes no liability for the customer’s failure to comply with these
requirements.
1.2.1 Grounding
To avoid damaging the sensitive electronic components in the LTE-Lite GSPDO kit or board always
make sure to discharge any built-up electrostatic charge to a good ground source, such as power
supply ground. This should be done before handling the circuit board or anything connected to it, i.e.
the GPS antenna.
1.2.2 Antenna Lightning Protection
Always use a UL-certified, properly installed Antenna Lightning suppressor on the antenna cable
when mounting the GPS antenna. Without proper Lightning Protection damage to equipment, injury,
or death may result.
1.2.3 Power Connections
Make sure to connect the DC power to the device following the polarity indicated in Section 2.1. Do
not reverse the power pins as this will cause serious damage to the circuit board.
1.2.4 Environmental Conditions
This instrument is intended for indoor use. It is designed to operate at a maximum relative
non-condensing humidity of 95% and at altitudes of up to 4000 meters. Refer to the specifications
tables for the ac mains voltage requirements and ambient operating temperature range.
© 2020 Jackson Labs Technologies, Inc. 3
LTE-Lite User Manual
Usage Instructions
2.1 Powering Up the Evaluation Board
The LTE-Lite Evaluation Board is essentially a plug-and-play product that only requires a power
source and a GPS antenna to be connected to start generating highly-accurate output frequency and
1PPS signals that are phase and frequency aligned to UTC (USNO) and thus allow NIST-tracability.
To use the Evaluation Board, simply plug in the power supply using the supplied USB cable, plug in
the antenna, and wait about 15 minutes typically for the GREEN “LOCK-OK” LED to light up to
indicate that the unit is locked to UTC with better than +/-250ns phase accuracy, and a frequency
accuracy of better than 1ppb has been achieved. The internal software will auto-configure and
auto-calibrate the unit without any user-interaction and the longer the unit runs the more accurate it
will become.
For units with a Timing GPS receiver, the unit will start an Auto Survey process to establish the
stationary antenna position as soon as power is applied, and this is indicated by the SURVEY LED on
the Evaluation Board. The Auto Survey process will take at least 2000 seconds to finish, at which
time the antenna position is stored in internal memory, and operation with 1 satellite is possible (4
sats are required for Mobile mode/non-Position-Hold operation).
The Evaluation Board is powered directly from the USB cable, and/or from an optional external 5V
DC source on the +5V header. The USB cable and the external 5V DC source may be connected at
the same time as they are diode-protected from one another. The current is typically less than 0.07A
at 5V. Connect a clean +5V power supply to the +5V header block if the USB cable is not going to be
used, or is plugged-in intermittently. See Figure 2.3 for the proper polarity of the optional external
5V DC power connection. Reversing the polarity on the power connector will not damage the unit as
it is diode reverse-polarity protected.
When communicating to the unit through the USB cable, Windows Vista, Windows 7/8 and Linux
will auto-recognize the unit as a USB serial COM adaptor, and automatically assign a serial port to
the unit. Windows will automatically load the USB COM driver for the board, and may need to have
access to the Internet to download the latest driver from the Microsoft update website. The user can
verify the COM port that windows assigned to the unit under the Computer Management window
(right click on computer and press the “MANAGE” button under Windows 7, or go to Control
Panel/Computer Management). The unit should show up as a standard serial port adaptor under the
“Ports (COM& LPT)” Icon. Please note the COM port number, as it is required for the initialization
of application software.
LTE-Lite User Manual
4© 2020 Jackson Labs Technologies, Inc.
The unit will start to search for satellites as soon as power is applied, and will start to lock the internal
TCXO to UTC as soon as a GPS antenna is attached and more than 4 sats become visible. After 30
minutes or less the unit should stabilize the frequency, and all ALARM indicators should be off
resulting in the Green “LOCK OK” LED to be lit up. At this time the Green LED will indicate the
unit is fully synchronized to UTC, and generating a stable and accurate 20MHz/19.2MHz/10MHz
output signal. The Green LED may go off momentarily from time to time as airflow touches the unit
or sats come in and out of view - this is normal behavior.
You may place the GPS antenna in a window, but it is recommended to place the GPS antenna with a
full view of the sky for best performance. The antenna cable can be extended to 100m or more with
high quality antenna cable (use quad shielded RG-6 75 Ohms cable, or high-quality 50 Ohms coax
cable) without significant loss of signal quality.
WARNING: Make sure to use a proper and certified Antenna Lightning Arrestor when placing
the antenna outside as lightning strikes can cause damage, injury, or death to equipment and
personnel.
Figure 2.1 LTE-Lite Evaluation Board with LTE-Lite Module
2.1.1 Airflow Warning
The LTE-Lite SMT module and thus the LTE-Lite Evaluation Board are very sensitive to airflow.
This includes airflow from convection, walking past the unit, or Air Conditioning systems. For
optimal performance the user must insure that the unit is shielded from any airflow by placing the
unit into an enclosure (for example Hammond PN: 1455C801BK). Please note that the external
DIP-14 TCXO and its socket must be removed from the PCB for it to fit into the aforementioned
Hammond enclosure. For optimal stability performance of the TCXO the unit should be sealed into
an airtight enclosure.
© 2020 Jackson Labs Technologies, Inc. 5
LTE-Lite User Manual
2.1.2 Supplied Accessories
The LTE-Lite Evaluation Kit includes the LTE-Lite Evaluation Board and is supplied with a GPS
antenna with 5m cable, a USB cable, a USB wall-wart power supply, and two MMCX to BNC
adaptor cables and is ready-to-go out of the box.
Figure 2.2 LTE-Lite Evaluation Kit example Accessories
2.1.3 USB Serial Port
The LTE-Lite Evaluation Board has an internal RS-232 to USB serial port adaptor. This allows the
unit to be directly connected to a PC’s USB port, from which it will receive power and to which it
will send serial output sentences with no external RS-232 to USB adaptor is required. The term
“RS-232” and USB serial port are used interchangeably, as the RS-232 port is implemented and
connected via the USB serial connection. Windows and Linux have built-in support for this optional
serial port functionality.
2.1.4 Major connections
The LTE-Lite Evaluation Board has a number of connectors, switches, jumpers, headers and LEDs to
select and display status. These are driven by signals from the LTE-Lite GPSDO SMT module.
The major connections and features of the LTE-Lite Evaluation Board are shown in Figure 2.3.
LTE-Lite User Manual
6© 2020 Jackson Labs Technologies, Inc.
Figure 2.3 Major connections of the LTE-Lite Evaluation Board
2.1.5 Typical Phase Noise and ADEV Plots
The following plot shows a typical ADEV plot for the LTE-Lite Evaluation Board. The unit had been
operating for 5+ days, has not been moved or vibrated in any way, and was completely shielded from
airflow by placing the unit into an airtight enclosure.
Figure 2.4 Typical ADEV plot of 20MHz LTE-Lite Evaluation Board
Table des matières
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
