ISSYZONEPOS IPDA030 Manuel utilisateur
IPDA030/IPDA031
Portable Data Terminal
Quick Start Guide
www.issyzonepos.com
- 1 -
Overview
- 2 -
Removing & Installing battery
1. Firstly, put the left and right battery cover buckles down to the right position.
2. Make use of the flip-up (on the right side) space between the battery hatch
and the bottom shell to pull the battery cover out.
3. Firstly, insert the bottom of the battery into the plughole of the inside Battery
bunker, and then press the top of the battery.
- 3 -
Install TF/SIM card
1. Please choose the corresponding card slot to insert SIM card according to
the view.
(Note: the hand-hold terminal only supports Micro SIM card. The standard
SIM card slot is used to install the encrypted PSAM card.)
- 4 -
Device Charging
The device has two kinds of charging methods for option:
a: Put the right waterproof USB stopple out to insert into the USB cable
through the USB cable carried by the device.
b: Charge the device through the seating-type charger (needing to purchase it
separately).
Introduction on the seating-type charger charging:
1. The seating-type charger can put in one device and one battery at the same
time.
2. The left indicator light is an indicator light for the device charging and will
turn into red after power up. Note that it will not show the charging state and
please examine the led indicator light when the device is charging.
3. The right indicator light is an indicator light for battery charging, will turn into
red when charging and green when the battery has got a full charge.
- 5 -
Scanning Function
If your device is equipped with the scanning function of codes, please follow
the following instruction to use:
1. Please find the icon of scanning codes (Pic 1) and open it.
2. In the scanning and testing interface of Pic 2, please press Scan and then
scan the code.
- 6 -
NFC Function
If your PDA with NFC function, please operate it as below:
1. Please find the NFC APP (Pic 1) and open it.
2. In NFC testing interfaces in Pic 2, Pls read the card by NFC reading area.
(Note: NFC has the optional function. Please ensure your device has that
function, then you can use it.)
- 7 -
LF125K Function
If your PDA with LF function, please operate it as below:
1. Please find the icon of NFC (Pic 1) in the program listing (Pic 1) and open it.
2. In LF testing interface in Pic 2, Please read the card by LF reading area.
(Note: the reading-card function with low-frequency 125K has the optional
function. Please ensure your device has that function, then you can use it.)
- 8 -
UHF Function
If your PDA with UHF function, please operate it as below:
1. Please find the UHF APP (Pic 1) and open it.
2. In UHF testing interface in Pic 2, Please close the card to the inductive zone
and read it.
(Note: the reading-card function of UHF has the optional function. Please
ensure your device has that function, then you can use it.)
- 9 -
Function of fingerprint identification
If your PDA with fingerprint identification function, please operate it as below:
1. Please find the fingerprint icon (Pic 1) and open it.
2. In fingerprint testing interface in Pic 2, fingerprints can be collected and
identified.
(Note: fingerprint identification has the optional function. Please ensure your
device has that function, then you can use it.)
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels ISSYZONEPOS Terminal tactile
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
