Iomega ZIP drive 100 Manuel utilisateur

Installation Guide

• Installation and Configuration

• Troubleshooting

• Drive Specifications

drive

atapiatapi

atapi

100

For Integrator /OEM Only

Table of Contents

Installation Guide ............................................................. 1

Troubleshooting .............................................................. 13

Drive Specifications ........................................................ 16

Check system requirements.

• Pentium or higher IBM-compatible computer (recommended)

• Empty 31⁄2or 51⁄4inch drive bay with front panel access

• Embedded IDE interface or IDE card

• Windows NT, Windows 95, Windows 3.1, or

DOS version 5.0 or higher

• Iomega Tools software (included with the Zip ATAPI drive)

MBIOS Support: It is recommended that BIOS support for the

Zip ATAPI drive be disabled in the CMOS setup. On some systems

with autodetection, it will be necessary to specifically turn off

autodetection for the Zip ATAPI drive. Refer to the Owner’s

Manual for your computer if you need more information.

The Zip ATAPI drive meets the latest ATAPI specifications; however

some computers with early ATAPI support do not meet these

specifications and so may not work correctly with removable ATAPI

drives like the Zip ATAPI drive. Refer to the Zip ATAPI Errata sheet

for additional information. M

Unpack the Zip ATAPI drive.

CAUTION Before handling the Zip ATAPI drive, touch a grounded

metal object (like an unpainted metal screw on the back of your

computer) to discharge any buildup of personal static electricity. M

Tools

100MB Zip Tools Disk

(contains Tools software)

Install Diskettes

and User’s Guide

3.5" Universal

Installation Kit

(includes mounting screws)

1–

2–

3–

4–

Attachthe left rail 1 to the faceplate 3 insert bottom

tabfirst, then repeat process for the right rail

Attachthe DC cable 4onto the connector of the disk drive.

Slidethe disk drive into position, aligning the

bottomholes of the disk drive with posts of the bracket

assembly. Verifythat no gaps are present on the faceplate.

Alignthe disk drive retaining clip 5 over the center of the disk

driveas pictured. Slightlyflex the drive clip and push down until

bothclip tabs engage the slots on the bottom of each rail.

NOTE:6 Screws were provided in this kit to further secure

thebrackets to the disk drive if desired,

howeverTHIS IS NOT A NECESSARY STEP!

Zip ATAPI Drive

Installation Guide

DISCONNECT the computer power cord and

remove the cover. (Refer to your computer manual

if removal is unclear.)

On some computers (especially tower models), you may need to remove the

computer’s face plate as well as the cover in order to access the drive bays.

WARNING Always disconnect computer electrical power at power

source before beginning a computer hardware change. M

Identify the IDE interface connection you want

to use for the Zip ATAPI drive.

• If the computer has an IDE hard drive, there may be an available

connection on the primary IDE interface cable.

• If there are two drives connected to the primary IDE cable, connect

the Zip ATAPI drive on the secondary IDE channel or use an IDE

interface card.

• If there is not an existing IDE interface cable with an available

connection, you will need a standard 40-pin IDE interface cable for

connecting the Zip ATAPI drive.

Configure jumper settings on the Zip ATAPI

drive as needed for your system.

The Zip ATAPI drive ships ready to install as the second drive on the IDE

connection (slave configuration). If the Zip ATAPI drive will be the only

drive connected to the IDE interface cable, change the jumper setting to

master (drive 0). If the computer is a Cable Select system, use the “Cable

Select” jumper setting.

Cable Select

Jumper block

Master (Drive 0)

Slave (Drive 1)

(Factory setting)

Slave (Drive 1)

Use the slave jumper setting if the Zip ATAPI drive will be one of two drives

connected to the IDE interface cable and the other drive is configured as a

master drive. If there is one drive connected to the cable before the Zip drive

is installed, it is probably configured as a master; however, some IDE drives

require a different jumper setting when two drives are connected. If you

encounter any problems, refer to the documentation that came with the

existing IDE drive for additional jumper setting information.

Note that many CD-ROM drives will not support a slave drive. If you

connect the Zip ATAPI drive to the same IDE interface cable as a CD-

ROM, you may need to configure the Zip ATAPI drive as the master and

the CD-ROM as the slave.

Master (Drive 0)

The Zip ATAPI drive should be configured as a master (drive 0) if it will be

the only drive connected to the IDE interface cable, or if there will be two

drives connected to the cable and the other drive is configured as a slave. A

Zip ATAPI drive which is configured as a master will support either a second

Zip ATAPI drive which is configured as a slave or an IDE hard drive or CD-

ROM which is configured as a slave.

Installation Guide

Cable Select

Use this setting whenever the Zip ATAPI drive is installed on a computer that

features “Cable Select.” Note that this setting should be used whether the Zip

ATAPI drive will be the only drive connected to the Cable Select IDE cable or

one of two drives connected to the cable. On Cable Select systems, the drive

closest to the IDE controller is automatically the master drive.

MNOTE: If you do not have information from the computer

manufacturer stating whether or not the system uses Cable Select,

check the IDE interface cable. On a Cable Select system, there is an

open connection on one of the wires between the first and second

drive connectors. If there are no breaks or holes in the interface

cable, it is probably not a Cable Select system. M

Locate a vacant drive bay and remove the

panel cover.

The Zip ATAPI drive is ready to install in a 31⁄2inch drive bay. A mounting

bracket or sled must be used for installation in a 51⁄4inch drive bay.

-inch Bays

(After selecting bay,

go to step 7.)

-inch Bay

(After selecting bay,

go to step 6a.)

51⁄4-inch drive bays ONLY:

Use the 3.5-inch Universal Installation Kit to assemble a 51⁄4-inch

mounting bracket and attach it to the drive, then go to step 7.

MInstructions for assembling the mounting bracket are

printed on the box. M

Attach the left rail 1 to the faceplate 3 insert bottom

tab first, then repeat process for the right rail

Attach the DC cable 4onto the connector of the disk drive.

Slide the disk drive into position, aligning the

bottom holes of the disk drive with posts of the bracket

assembly. Verifythat no gaps are present on the faceplate.

Align the disk drive retaining clip 5 over the center of the disk

drive as pictured. Slightlyflex the drive clip and push down until

both clip tabs engage the slots on the bottom of each rail.

NOTE: 6 Screws were provided in this kit to further secure

the brackets to the disk drive if desired,

however THIS IS NOT A NECESSARY STEP!

1–

2–

3–

4–

Check mounting requirements: Your drive bay

may require side rails.

MHINT: Check other drives in the system (such as a CD-ROM drive)

to see if they use mounting rails. If so, you may need similar

mounting rails for the Zip ATAPI drive. If the computer does not

include extra mounting rails, contact your computer dealer to obtain

the rails you need. M

-inch Bay 5

-inch Bay

Check for correct mounting orientation before

sliding the drive into the drive bay.

Correct mounting orientations

Do not mount vertically with

the left side of the drive down!

Installation Guide

Slide the Zip drive into the drive bay.

MNOTE: If it makes it easier to connect cables on your computer,

you can secure the Zip drive in the drive bay now. (See step 12 for

instructions on securing the drive.) M

Use a standard 40-pin interface cable to

connect the Zip ATAPI drive to the computer’s

embedded IDE interface or IDE card.

CAUTION Make sure PIN 1 on the cable connects to PIN 1 on the

Zip ATAPI drive. All IDE interface cable connections must maintain

correct pin 1 orientation in order for the Zip drive to be recognized

by the system. M

PIN 1

Zip ATAPI Drive

Pin 1

40-pin Interface Cable Connector

Stripe on Interface Cable indicates Pin 1

Connect a computer power supply cable.

MN0TE: If all available power supply cables have micro connectors,

you will need a power cable converter. If the computer does not

have a spare power supply cable, you will need a power Y-cable. M

Zip ATAPI Drive

Power Supply Cable from Computer

CAUTION Make sure the power supply cable is securely connected to

the Zip drive. M

Secure drive in drive bay (mounting screws are in

the 3.5” Universal Installation kit).

Align the front of the Zip drive with other drives installed in the computer.

If there is not clear access to the drive bay mounting holes, refer to your

computer manual for additional instructions. Note that if the drive is held

in place securely by rails, you will not need to use the mounting screws.

Drive Bay Mounting

Screws (6-32)

CAUTION Mounting screws must not extend into the Zip ATAPI

drive farther than 4.0 mm (about 0.16 inch). Mounting screws that

are too long could damage the drive. M

Installation Guide

Check all connections, arrange the cables to

fit under the cover, and replace the

computer cover.

Reconnect power cord, turn ON power switch,

and wait for the operating system to load.

Insert the 100MB Zip “tools” disk into the Zip

drive.

CAUTION Always make sure computer power is ON before inserting

a Zip disk! M

When you insert a Zip disk, the green busy light in the eject button will

flash momentarily. When the eject button is pushed, the drive takes a few

seconds to deliver the disk.

Tools

Eject Button / Green Busy Light

(Flashes when drive is transferring data,

or when inserting or ejecting a disk)

Disk Inserted

Insert Gently!

Autres manuels pour ZIP drive 100

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Iomega Stockage

Iomega

Iomega eGo 33832 Manuel utilisateur

Iomega

Iomega Portable Hard Drive eGo Helium Manuel utilisateur

Iomega

Iomega Desktop Hard Drive UDB Manuel utilisateur

Iomega

Iomega Portable Hard Drive USB / FireWire Manuel utilisateur

Iomega

Iomega eGo 34491 Manuel utilisateur

Iomega

Iomega REV 35 Instructions d'utilisation

Iomega

Iomega Home Network Hard Drive Instructions d'utilisation

Iomega

Iomega Prestige 34807 Manuel utilisateur

Iomega

Iomega Zip 750MB Instructions d'utilisation

Iomega

Iomega CD-RW USB 2.0 Manuel utilisateur

Iomega

Iomega Media Xporter 33992 Manuel utilisateur

Iomega

Iomega 34579 Manuel utilisateur

Iomega

Iomega Media Xporter 33992 Manuel utilisateur

Iomega

Iomega 34151 - ScreenPlay Pro HD Multimedia Drive Manuel utilisateur

Iomega

Iomega StorCenter Manuel utilisateur

Iomega

Iomega px4-400d Manuel utilisateur

Iomega

Iomega 3798300 Manuel utilisateur

Iomega

Iomega Peerless Manuel utilisateur

Iomega

Iomega Floppy USB Drive Instructions d'utilisation

Iomega

Iomega ScreenPlay HD 500GB Manuel utilisateur

Iomega

Iomega 35180 Manuel utilisateur

Iomega

Iomega Zip USB Powered Drive Instructions d'utilisation

Iomega

Iomega 34278 Manuel utilisateur

Iomega

Iomega eGo 34985 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur