Invacare LYNX LX-3 Manuel

Unpacking/Setup Instructions

Lynx LX-3TM Scooter

DEALER: THIS MANUAL MUST BE GIVEN

TO THE USER OF THE WHEELCHAIR.

USER: BEFORE USING THIS WHEEL-

CHAIR, READ THIS MANUAL AND SAVE

FOR FUTURE REFERENCE.

Instrucciones Para Desempacar y Ensamblar El Escúter

DISTRIBUIDOR: ESTE MANUAL DEBE DE

SER ENTREGADO AL USUARIO DEL

ESCUTER.

USUARIO: ANTES DE USAR EL ESCUTER,

LEA ESTE MANUAL Y GUARDELO PARA

FUTURA REFERENCIA.

Tiller

Front Basket

Headlight

On-Board Battery Charger

Floor Basket

Rear Shroud

Seat

LYNX LX-3 SCOOTER

DISASSEMBLED VIEW

Front Basket

Batteries

Rear Sub-Frame

Assembly

Rear Shroud

Seat

Front Sub-Frame

Assembly

LYNX LX-3 SCOOTER

Congratulations on the purchase of your new LYNX LX-3 Scooter. To ensure safe and proper operation of

your scooter, DO NOT attempt to operate your scooter without first reading the Owner's Operator and

Maintenance Manual.

Before proceeding, check to ensure that you have three (3) cartons:

●One (1) large carton containing the scooter

●Two (2) battery cartons

Tools needed for setup and assembly:

● 7/16 Box Wrench or Crescent Wrench

● The use of rubber gloves and safety glasses is recommended when working with batteries.

The instructions contained in this manual were written to provide a step-by-step guide for assembly and setup of

your scooter. A space is provided to check off each step as it is completed.

If you have difficulty with the instructions, or with setup and assembly of your scooter, you may call Invacare

Customer Service at 1-800-343-6059 for assistance.

A. REMOVING THE SCOOTER FROM THE CARTON (FIGURE 1)

WARNING

The Lynx LX-3 scooter weighs 110-lbs. (50kg) without the batteries. DO NOT attempt to lift a powered

scooter by any removable (detachable) parts. Improper lifting may result in injury to the user or assis-

tants, or damage to the powered scooter.

To properly remove the scooter from the carton, perform the following steps:

Check Box When

Completed

1. Cut along the seams at the end of the carton that is closest to the scooter seat.

2. Lay the end of the carton down (flat) on the floor.

3. Before attempting to roll the scooter out of the carton, you must first place the brake-release lever in

the "OFF" position (DETAIL "A" of FIGURE 1).

4. Raise the seat back to the upright position (DETAIL "B" of FIGURE 1).

5. To roll the scooter out of the carton, grasp the seat back and gently pull the scooter backwards out of

the carton.

6. Locate the Owner's Operator and Maintenance Manual, part number 1090132. You will need to refer

to this manual as a part of the setup procedures and for safe operation and maintenance of your

scooter.

7. Remove the remaining packing and protective covering material from the scooter.

FIGURE 1 - REMOVING THE SCOOTER FROM THE CARTON

Brake

Release

Lever

Rear of

Scooter

Back

(Upright

Position)

Seat

DETAIL "A" DETAIL "B"

REMOVING THE SCOOTER FROM THE CARTON

B. TILLER ASSEMBLY (FIGURE 2)

WARNING

SectionBisonlytoaccommodatetheremovalofthefrontbasketfromthefloorarea of the scooter.DO

NOT operate the scooter until the proper tiller adjustment procedure (refer to PROCEDURE 8 of the

Owner'sOperatorandMaintenancemanual,partnumber1090132)hasbeenperformedaftercomple-

tion of these setup instructions.

DO NOT insert the key into the ignition while performing these setup instruction - otherwise, injury or

damage may occur.

To raise the tiller assembly, perform the following steps:

Check Box When

Completed

1. Locate the tiller release lever on the lower left side (facing the scooter) of the tiller (FIGURE 2).

2. While supporting the tiller with one (1) hand, push the tiller release lever to the UNLOCKED position

with the other hand (FIGURE 2).

3. Raise the tiller to the upright position and pull the release lever to the LOCKED position, ensuring the

adjustment pin is engaged in one (1) of the five (5) holes in the adjustment plate.

4. Gently pull/push against the tiller to ensure the tiller is securely engaged into the locking mechanism.

5. Remove the keys from the tiller adjustment plate and place in a safe and secure location.

Tiller Release Lever

UNLOCKED

FIGURE 2 - TILLER ASSEMBLY

Tiller Release Lever

LOCKED

Tiller

Adjustment

Plate

Tiller

Adjustment

NOTE: The tiller adjustment plate shown in FIGURE 2

has three (3) adjustment positions instead of five (5).

TILLER ASSEMBLY

NOTE: The delta tiller is NOT shown.

C. FRONT BASKET INSTALLATION (FIGURE 3)

Check Box When

Completed

1. Remove the front basket from the floor area of the scooter.

2. Remove the packing material that held the basket in place for shipping.

3. Remove the following five (5) items from inside the front basket and set aside for future use:

A. AC Power Cord (

NOTE: This is used for battery charging procedure

)

B. Two (2) Anti-Tipper Wheel Assemblies

C. Knob (

NOTE: This is a spare part to be used if a knob is lost

)

D. Nut/Bolt (

NOTE: This is ONLY used for the optional flag or cane holder, save for future use if

optional flag or can holder was not purchased.

)

To properly install the front basket, perform the following steps:

Check Box When

Completed

1. Align the slots of the front basket with the mounting clips located on the front of the tiller (FIGURE 3).

2. Push down on the front basket to secure it in place.

FIGURE 3 - FRONT BASKET INSTALLATION

Front Basket

Slots Shroud

Of Tiller

Mounting Clips

FRONT BASKET INSTALLATION

Check Box When

Completed

4. Remove the two (2) wide "VELCRO®like" straps from around the bottom of the frame post - these are

the battery lifting straps and will be used later in the battery installation process. These two (2) straps

are wrapped together and will need to be separated (DETAIL "A" of FIGURE 5).

NOTE: DO NOT remove the narrow "VELCRO

like" strap that runs across the back of the scooter - this

is the battery fastening strap.

5. Disconnect the RED connector of the BATTERY wiring harness from the RED connector on the

CONTROLLER wiring harness and set aside (DETAIL "B" of FIGURE 5).

6. Disconnect the BLACK connector of the BATTERY wiring harness from the BLACK connector on the

CONTROLLER wiring harness and set aside (DETAIL "B" of FIGURE 5).

FIGURE 4 - PREPARING THE SCOOTER/BATTERIES FOR INSTALLATION

Seat

DETAIL "B"DETAIL "A"

Seat Post

Frame Post

Stability

Knob

Rear

Shroud

Frame

Support

VELCRO® is a registered trademark of Velcro Industries B.V.

D. BATTERY INSTALLATION

Preparing The Scooter/Batteries For Installation (FIGURES 4, 5 AND 6)

To properly prepare the scooter/batteries for installation, perform the following steps:

Check Box When

Completed

1. Unscrew and remove the stability knob located under the seat on the front of the frame post (DETAIL

"A" of FIGURE 4).

WARNING

DO NOT lift the seat by the arm rests - otherwise, injury or damage may occur.

2. Lift the seat assembly up and remove it from the frame support (DETAIL "A" of FIGURE 4).

3. Lift the rear shroud off of the frame post (DETAIL "B" of FIGURE 4).

NOTE: You will hear a "VELCRO

like" unhooking sound when removing the shroud.

BATTERY INSTALLATION

WARNING

BEFORE PROCEEDING WITH THE BATTERY INSTALLATION, READ THE FOLLOWING:

To ensure safe handling and that the proper procedures are followed for the battery installation, refer to

BATTERIES AND CHARGING in PROCEDURE 4 of the Owner's Manual, part number 1090132. Once you

have read and understand PROCEDURE 4 in the Owner's Manual, you may proceed with the following

instructions.

Check Box When

Completed

7. Locate the two (2) battery boxes and carefully remove the batteries from the boxes.

NOTE: The weight of each battery is 23 lbs. (10 Kg.).

8. Locate one (1) of the two (2) wide "VELCRO®like" battery lifting straps (Refer to STEP 4 of this

procedure) and place it smooth side up (hook side down) on a flat surface (FIGURE 6).

9. Place one (1) of the batteries, front to back, on top of the strap by making sure the following occurs:

A. The two (2) battery terminal posts are on the TOP, REAR edge of the battery (FIGURE 6).

B. The retaining ring on the battery lifting strap is located at the BACK, REAR edge of the battery

(FIGURE 6).

10. Wrap the battery lifting strap around the battery, making sure it runs BETWEEN the two (2) battery

terminal posts (FIGURE 6).

11. Pull the end of the battery lifting strap WITHOUT the retaining ring THROUGH the retaining ring at the

opposite end of the battery lifting strap (FIGURE 6).

NOTE: When the lifting strap is pulled tight, the retaining ring should be positioned in the MIDDLE of the

BACK side of the battery.

12. If necessary, adjust the battery lifting strap by placing one (1) hand BETWEEN the battery lifting strap

and the TOP of the battery, then secure the remaining loose end by pressing the "VELCRO®like"

material together.

13. Test that the battery is secure and positioned properly for lifting and transporting by using two (2)

hands (one (1) hand under the strap on the TOP of the battery, and the other to balance the battery)

to carefully lift the battery.

FIGURE 5 - PREPARING THE SCOOTER/BATTERIES FOR INSTALLATION

DETAIL "B"DETAIL "A"

RED

Connector

Battery Lifting Straps

(Remove From Around

Frame Post)

Battery Fastening

Strap (DO NOT

Remove) BLACK

Connector

Rear Sub

Frame

Battery Wiring Harness

RED

Connector

BLACK

Connector

Controller

Wiring

Harness

Preparing The Scooter/Batteries For Installation (FIGURES 4, 5 AND 6) - Continued

BATTERY INSTALLATION

VELCRO® is a registered trademark of Velcro Industries B.V.

Battery

Wiring

Harness

Connecting The Battery Wiring Harness To The Battery (FIGURES 7 AND 8)

To properly connect the battery wiring harness to the battery, perform the following steps:

Check Box When

Completed

1. Locate the battery wiring harness with the BLACK connector at one (1) end (FIGURE 7).

NOTE: There are two (2) battery wiring harnesses - one (1) with a BLACK connector and one (1) with a

RED connector.

CAUTION

When tightening the screws/locknuts on the battery terminal posts, always use a box or a crescent

wrench. Pliers will round off the nuts. Never wiggle the terminal when tightening. Otherwise, the battery

maybecome damaged.

2. Remove the mounting screw and locknut from the NEGATIVE (-) battery terminal post (FIGURE 8).

NOTE: To establish a ground, make the BLACK cable to NEGATIVE (-) battery terminal post connection first.

3. Connect the battery cable with the BLACK boot to the NEGATIVE (-) battery terminal post using the mounting

screw and locknut (FIGURE 8). Tighten the screw and locknut using a 7/16 box or Crescent wrench.

4. Push the BLACK battery cable boot down over the NEGATIVE (-) battery terminal post, covering the

terminal post, mounting screw and locknut (FIGURE 8).

FIGURE 7 - CONNECTING THE BATTERY WIRING HARNESS TO THE BATTERY

Battery

Wiring

Harness

Black

Connector Battery

Wiring

Harness

Red

Connector

FIGURE 6 - PREPARING THE SCOOTER/BATTERIES FOR INSTALLATION

Battery

Lifting

Strap

Smooth Side Up

Battery

Terminal Post

(NOT

SHOWN)

Battery

Terminal Post

(NOT

SHOWN)

Top,

Rear

Edge

Battery

Lifting

Strap

Retaining

Ring

Preparing The Scooter/Batteries For Installation (FIGURES 4, 5 AND 6) - Continued

NOTE: DO NOT position the battery in the scooter at this time.

14. Repeat STEPS 7-14 for the other battery.

BATTERY INSTALLATION

Installing The Batteries Into The Scooter (FIGURES 9, 10, 11 AND 12)

To properly install the batteries into the scooter, perform the following steps:

Check Box When

Completed

1. Loosen the battery fastening strap, making sure that both ends of the battery fastening strap are

laying outside of the scooter so the batteries will not be set down on the battery fastening strap

(FIGURE 8).

2. Ensure the area behind the floor basket (where the batteries will be installed) is free of all material and

ready for the batteries to be installed.

3. Remove the retaining pin that holds the front frame assembly and the rear frame assembly together

(FIGURE 10).

4. Temporarily place the retaining pin inside the frame post (FIGURE 10).

NOTE: DO NOT lift up on either the front or rear frame assemblies when the pin is removed. Otherwise,

the front frame will separate from the rear frame.

Battery

Fastening

Strap Laying On

Outside Of

Scooter

FIGURE 9 - INSTALLING THE BATTERIES INTO THE SCOOTER

Connecting The Battery Wiring Harness To The Battery (FIGURES 7 AND 8) - Continued

5. Remove the mounting screw and locknut from the POSITIVE (+) battery terminal post

6. Connect the battery cable with the RED boot to the POSITIVE (+) battery terminal post using the

mounting screw and locknut. Tighten the screw and locknut using a 7/16 box or Crescent wrench.

7. Push the RED battery cable boot down over the POSITIVE (+) battery terminal post, covering the

terminal post, mounting screw and locknut.

8. Locate the battery wiring harness with the RED connector at one (1) end (FIGURE 7).

9. Repeat STEPS 2-8 for the second battery.

FIGURE 8 - CONNECTING THE BATTERY WIRING HARNESS TO THE BATTERY

Mounting Screws

Locknuts

Battery Wiring

Harness With

Black Connector

Battery Cable

Black Boot

Positive (+) Battery Terminal Post

Negative (-) Battery

Terminal Post

Battery Cable Red Boot

BATTERY INSTALLATION

NOTE: DO NOT put the pin into the large hole in the frame post.

8. Ensure that the area where the second battery is to be installed is free of all material and ready for the

battery to be installed.

9. Locate the battery with the RED connector at the end of the battery wiring harness.

10. Carefully lift the battery using the battery lifting strap (using one (1) hand under the strap on the TOP

of the battery, and the other to balance the battery) and place it in the open area just behind the LEFT

side of the floor basket (FIGURE 11).

NOTE: The battery terminals should be towards the rear of the scooter (FIGURE 11).

NOTE: DO NOT connect the battery wiring harness at this time.

FIGURE 11 - INSTALLING THE BATTERIES INTO THE SCOOTER

Front Of Scooter

Rear Of Scooter

TOP VIEW OF REAR PORTION OF SCOOTER

Battery Terminals Battery Terminals

Battery

Black Connector

Battery Wiring Harness

Battery

Red Connector

Battery Wiring Harness

Installing The Batteries Into The Scooter (FIGURES 9, 10, 11 AND 12) - Continued

Retaining Pin

Frame Post

Place Retaining Pin Here

5. Locate the battery with the BLACK connector at the end of the battery wiring harness.

6. Carefully lift the battery using the battery lifting strap (using one (1) hand under the strap on the TOP

of the battery, and the other to balance the battery) and place it in the open area just behind the

RIGHT side of the floor basket (FIGURE 11).

NOTE: The battery terminals should be towards the rear of the scooter (FIGURE 11).

NOTE: DO NOT connect the battery wiring harness at this time.

7. From the rear of the scooter, replace the retaining pin by passing it through both the FRONT and the

REAR frame assemblies (FIGURE 10).

FIGURE 10 - INSTALLING THE BATTERIES INTO THE SCOOTER

Front Frame Assembly Rear Frame Assembly

BATTERY INSTALLATION

Table des matières

Langues :

Autres manuels Invacare Scooter

Invacare

Invacare Canada LP Manuel utilisateur

Invacare

Invacare Zoom-3 Manuel utilisateur

Invacare

Invacare Pegasus Manuel utilisateur

Invacare

Invacare Spectra Blitz Manuel utilisateur

Invacare

Invacare electra Manuel utilisateur

Invacare

Invacare Comet Mode d’emploi

Invacare

Invacare Zoom 220 Manuel

Invacare

Invacare Lynx Manuel utilisateur

Invacare

Invacare Comet Manuel utilisateur

Invacare

Invacare Lynx Series Manuel

Invacare

Invacare electra Manuel utilisateur

Invacare

Invacare orion Manuel utilisateur

Invacare

Invacare Comet Series Manuel utilisateur

Invacare

Invacare Lynx L-4 Manuel utilisateur

Invacare

Invacare LYNX LX-3PLUS Manuel d'utilisation

Invacare

Invacare meteor Manuel utilisateur

Invacare

Invacare Lynx L-4 Manuel

Invacare

Invacare P780 Instructions de montage

Invacare

Invacare Cetus Manuel utilisateur

Invacare

Invacare Cetus Manuel utilisateur

Invacare

Invacare Colibri Manuel utilisateur

Invacare

Invacare Comet Series PRO Manuel utilisateur

Invacare

Invacare CometALPINE+ Manuel utilisateur

Invacare

Invacare Orion Series Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur