IntesisBox IBOX-BAC-DALI Manuel utilisateur

IntesisBox

BACnet/IP Server

DALI

User's manual

r1 eng

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

2 / 26

Gateway for the integration of DALI ballast devi es

into BACnet/IP ontrol systems.

Order code:

IBOX-BAC-DALI

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

3 / 26

Information in this do ument is subje t to hange without noti e. The software des ribed in

this do ument is furnished under a li ense agreement or nondis losure agreement. The

software may be used only in a ordan e with the terms of those agreements. No part of

this publi ation may be reprodu ed, stored in a retrieval system or transmitted in any form

or any means ele troni or me hani al, in luding photo opying and re ording for any

purpose other than the pur haser’s personal use without the written permission of Intesis

Software S.L.

Intesis Software S.L.

Milà i Fontanals, 1 bis - 1º

08700 Igualada

Spain

TRADEMARKS

All trademarks and trade names used in this document are acknowledged to be the copyright of their respective holders

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

4 / 26

INDEX

IntesisBox BACnet/IP Server – DALI Des ription.................................................. 5

1.1

DALI interfa e.............................................................................................. 6

1.2

BACnet/IP interfa e ...................................................................................... 7

Installation and qui k-setup .............................................................................10

2.1

IntesisBox hardware ................................................................................... 10

2.2

Qui k-setup............................................................................................... 10

2.2.1

DALI onne tion setup............................................................................. 11

2.2.2

Ethernet onne tion setup ....................................................................... 11

LinkBoxBa net software tool ............................................................................13

3.1

Installation................................................................................................ 13

3.2

Offline and Online working modes ................................................................ 13

3.3

Proje t definition ........................................................................................ 13

3.4

Editing the onfiguration proje t for DALI ...................................................... 16

3.4.1

IntesisBox Configuration Window .............................................................. 16

3.4.2

Swit hing from Offline to Online mode....................................................... 16

3.4.3

Configuration of short addresses for DALI ballasts....................................... 17

3.4.4

Ballast onfiguration values...................................................................... 20

3.4.5

BACnet onfiguration............................................................................... 22

3.5

Signals viewer ........................................................................................... 23

3.6

Bus viewers ............................................................................................... 23

Me hani al & ele tri al hara teristi s ...............................................................25

Dimensions....................................................................................................26

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

5 / 26

1. IntesisBox BACnet/IP Server – DALI Description

This do ument des ribes the integration of DALI ballasts in BACnet ompatible devi es and

systems (ANSI/ASHRAE 135 – 2001 / Annex J - BACnet/IP), with the use of IntesisBox

BACnet/IP Server – DALI devi e.

The ending of this devi e is:

Providing a DALI physi al hannel with the ne essary bus voltage (about 15V) and

urrent regulation (max. 250mA).

Setting the proper onfiguration values of the DALI ballasts (addresses, groups,

max/min levels, …).

Performing ontrol and monitoring of the DALI ballasts in the DALI bus from a

BACnet/IP-based ontrol system or devi e, so that the ballasts be ome part of the

own BACnet system.

A onfiguration software tool, Lin BoxBacnet, is provided with IntesisBox, allowing to

perform all setup tasks related to onfiguration of DALI ballasts, setting needed BACnet/IP

parameters (IP address, TCP port, …) as well as providing basi monitoring of the

integration at setup time.

On e set up, the gateway a ts as a BACnet/IP Server devi e in its BACnet interfa e,

allowing other BACnet/IP lient devi es to perform COV subs ription requests, and reading

or writing its internal BACnet obje ts. These obje ts provide ontrol of the DALI ballasts

onne ted to IntesisBox.

This do ument assumes that the user is familiar with BACnet and DALI te hnologies and

their te hni al terms.

Figure 1 - Integration of DALI ballasts into BACnet/IP using IntesisBox BACnet/IP

Server - DALI

DALI bus

BACnet/IP

client

Ethernet

LAN

TCP/IP

BACnet/IP

client

DALI ballasts

EIA232

Only needed for configuration

(configuration can also be done using Ethernet)

LinkBoxBacnet

Configuration

Software

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

6 / 26

1.1 DALI interface

DALI (Digitally Addressable Lighting Interfa e) is a standard defining a set of fun tionalities

and requirements to be fulfilled by lighting ballasts. DALI ballasts ommuni ate as well

using the same proto ol (DALI proto ol), defined in the standard and supported by

IntesisBox.

From a fun tional point of view, DALI ballasts provide following features:

Digital ontrol of a tual ar power level (dim level)

oControllable either individually, or by previously defined groups of ballasts.

oSet to arbitrary power/dim levels between OFF and 100%, or previously

defined “preset” levels (s enes).

oUsing predefined fade rates/times upon power level hange.

Reporting of their a tual status

oMainly for dete ting failure onditions of the ballast or the installation.

A single DALI hannel supports up to 64 ballasts, being this one the maximum number of

individual ballasts that an be integrated with a single IntesisBox.

The DALI hannel needs a power sour e, whi h will be provided by IntesisBox itself. As per

the requirements of the standard, nominal bus voltage provided by IntesisBox is 15V, and

has a urrent limiter of 240/250mA.

Ea h DALI ballast has an own permanent storage memory, where it stores its own

onfiguration values. These values an be read, set and hanged using IntesisBox at setup

time. They are the following:

Short Address (Individual address / Address for individual ontrol)

Random Address (Unique address providing a way of addressing a ballast without

assigned individual/short address)

Physi al Minimum Level (read-only/defined by ballast manufa turer)

Minimum Level

Maximum Level

Power-on Level

System Failure Level

Fade Rate

Fade Time

Group membership (a DALI hannel an have up to 16 groups and ea h ballast an

belong to any number of them at the same time)

Level for s ene 0…15 (up to 16 s enes/preset dim levels an be onfigured within

ea h ballast)

Configuration of all ballast parameters an be done with IntesisBox, using Lin BoxBacnet

software onfiguration tool. Usage of this tool is explained in detail in se tion 3.

Information on DALI te hnology and a list of existing ballast manufa turers an be found at

AG DALI asso iation’s website (www.dali-ag.org).

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

7 / 26

1.2 BACnet/IP interface

DALI ballasts onne ted to IntesisBox are a essible by means of its BACnet/IP server

interfa e.

Ea h DALI ballast is abstra ted at BACnet side as a set of BACnet obje ts, using types

Analog Input and Analog Output. The value they represent is always a essed in IntesisBox

by means of its BACnet Property Present Value.

For ea h ballast, following is the list of its related BACnet obje ts:

Obje t Name Des ription BACnet

Type Obje t ID #

Dali Dxx PwrLvl Current ar power level reported by ballast xx

0% (off) … 100% / MAX level

Analog

Input xx

Dali Dxx PwrSet Requested ar power level on ballast xx

0% (off) … 100% / MAX level

Analog

Output xx

Dali Dxx Sts Byte value representing ballast xx status b

…b

Bit b

: Status of ballast

o0: Ballast is OK

o1: Ballast is in failure

Bit b

: Lamp failure

o0: Lamp is OK

o1: Lamp is in failure

Bit b

: Lamp arc power on

o0: Lamp is OFF

o1: Lamp is ON

Bit b

: Limit error

o0: Last requested ar power md between MIN and MAX level

(or OFF)

o1: Last requested ar power md is out of MIN/MAX level

range

Bit b

: Fade running

o0: No fade is running (fade is ready)

o1: Fade is running

Bit b

: Reset state

o0: No reset state

o1: Reset state (fa tory onfiguration values in ballast)

Bit b

: Missing short address

o0: Short address is programmed

o1: Missing short address

Bit b

: Power failure

o0: No ar power trl ommand re eived after power-up

o1: Ar power ontrol ommand re eived after power-up

Analog

Input

200 + xx

Dali Dxx Cmd Requested ommand on ballast xx

0 – Set Arc Power Off

1 – Arc Power 100%

2 – Step Up

3 – Step Down

10 – Set Minimum Arc Power Level

11 – Set Maximum Arc Power Level

1yy – Go to Scene yy

2yy – Store Current Level as Scene yy

3yy – Clear/Remove Scene yy

1yyy – Set Fade Rate to yyy (steps/second)

2yyy – Set Fade Time to yyy (seconds)

3yyy – Set Max Level Rate to yyy (in %)

4yyy – Set Min Level Time to yyy (in %)

5yyy – Set Power-on Level Time to yyy (in %)

6yyy – Set System-failure Level to yyy (in %)

Analog

Output

200 + xx

This ommand will overwrite ballast’s permanent storage memory. Permanent storage memories have a limited rated number of writes. Therefore,

intensive/repetitive use of this ommand will harm your ballast’s permanent storage memory.

In the list, value xx poses as the ballast short/individual address, and takes value 0 to 63.

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

8 / 26

Additionally, IntesisBox implements two Analog Outputs allowing group-based ontrol of

ballasts. See following list:

Obje t Name Des ription BACnet

Type Obje t ID #

Dali Gxx PwrSet Requested ar power level on group xx

0% (off) … 100% / MAX level

Analog

Output 100 + xx

Dali Gxx Cmd Requested ommand on group xx

0 – Set Arc Power Off

1 – Arc Power 100%

2 – Step Up

3 – Step Down

10 – Set Minimum Arc Power Level

11 – Set Maximum Arc Power Level

1yy – Go to Scene yy

2yy – Store Current Level as Scene yy

3yy – Clear/Remove Scene yy

1yyy – Set Fade Rate to yyy (steps/second)

2yyy – Set Fade Time to yyy (seconds)

3yyy – Set Max Level Rate to yyy (in %)

4yyy – Set Min Level Time to yyy (in %)

5yyy – Set Power-on Level Time to yyy (in %)

6yyy – Set System-failure Level to yyy (in %)

Analog

Output 300 + xx

This ommand will overwrite ballasts’ permanent storage memory. Permanent storage memories have a limited rated number of writes. Therefore,

intensive/repetitive use of this ommand will harm your ballasts’ permanent storage memory.

In the list, value xx poses as the group number being ontrolled, and takes value 0 to 15.

Additionally, IntesisBox implements two Analog Outputs allowing broad ast ontrol of all

ballasts together. See following list:

Obje t Name Des ription BACnet

Type Obje t ID #

Dali All PwrSet Requested ar power level to all ballasts

0% (off) … 100% / MAX level

Analog

Output 116

Obje t Name Des ription BACnet

Type Obje t ID #

Dali All Cmd Requested ommand to all ballasts

0 – Set Arc Power Off

1 – Arc Power 100%

2 – Step Up

3 – Step Down

10 – Set Minimum Arc Power Level

11 – Set Maximum Arc Power Level

1yy – Go to Scene yy

2yy – Store Current Level as Scene yy

3yy – Clear/Remove Scene yy

1yyy – Set Fade Rate to yyy (steps/second)

2yyy – Set Fade Time to yyy (seconds)

3yyy – Set Max Level Rate to yyy (in %)

4yyy – Set Min Level Time to yyy (in %)

5yyy – Set Power-on Level Time to yyy (in %)

6yyy – Set System-failure Level to yyy (in %)

Analog

Output 117

This ommand will overwrite ballasts’ permanent storage memory. Permanent storage memories have a limited rated number of writes. Therefore,

intensive/repetitive use of this ommand will harm your ballasts’ permanent storage memory.

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

9 / 26

Finally, there is a set of 8 Analog Input obje ts reporting, in a ompa t way, a faulty status

of ea h ballast in the line.

Obje t Name Des ription BACnet

Type Obje t ID #

Dali Err D07-00 Byte value b

…b

representing status of ballasts

with individual/short addresses 0 to 7, in the

following way:

Bit b

: Status of ballast 0

0: Ballast OK

1: Ballast not present in bus, ballast failure , lamp failure or

not onfigured in database

Bit b

: Status of ballast 1

…

Bit b

: Status of ballast 7

Analog

Input 100

Dali Err D15-08 Byte value b

…b

representing status of ballasts

with individual/short addresses 8 to 15.

relates to ballast 8, b

to ballast 9, …, b

to ballast 15)

Analog

Input 101

Dali Err D23-16 Byte value b

…b

representing status of ballasts

with individual/short addresses 16 to 23.

relates to ballast 16, b

to ballast 17, …, b

to ballast 23)

Analog

Input 102

Dali Err D31-24 Byte value b

…b

representing status of ballasts

with individual/short addresses 24 to 31.

relates to ballast 24, b

to ballast 25, …, b

to ballast 31)

Analog

Input 103

Dali Err D39-32 Byte value b

…b

representing status of ballasts

with individual/short addresses 32 to 39.

relates to ballast 32, b

to ballast 33, …, b

to ballast 39)

Analog

Input 104

Dali Err D47-40 Byte value b

…b

representing status of ballasts

with individual/short addresses 40 to 47.

relates to ballast 40, b

to ballast 41, …, b

to ballast 47)

Analog

Input 105

Dali Err D55-48 Byte value b

…b

representing status of ballasts

with individual/short addresses 48 to 55.

relates to ballast 48, b

to ballast 49, …, b

to ballast 55)

Analog

Input 106

Dali Err D63-56 Byte value b

…b

representing status of ballasts

with individual/short addresses 56 to 63.

relates to ballast 56, b

to ballast 57, …, b

to ballast 63)

Analog

Input 107

IntesisBox

BACnet/IP Server – DALI

User’s Manual eng r0

File: IBOX-BAC-DALI User Manual eng r1.pdf

IntesisBox is a registered trademark of Intesis Software SL

URL

tel

http://www.intesis.com

[email protected]

+34 938047134

10 / 26

2. Installation and quick-setup

2.1 IntesisBox hardware

Devi e uses a standard en losure allowing DIN EN60715 TH35 rail mounting. Its plasti

meets standard PC UL 94 V0.

Sizes are 159mm x 105mm x 58mm.

Ensure proper spa e for all onne tors when mounted.

The items supplied by Intesis Software for this integration are:

•IntesisBox BACnet/IP – DALI hardware

•Console able. Standard DB9F-DB9M able 1.8 meter long.

•Installation sheet, ontaining a hard-link for Lin BoxBacnet software download

and this manual.

2.2 Quick-setup

Mount IntesisBox in the desired lo ation (follow instru tions and re ommendations in its

installation sheet).

Next se tions detail preliminary he ks to perform to ensure DALI and Ethernet

onne tivity.

DALI Bus

Power

230Vac

PC Console

IntesisBox

www.intesis.com

POWER

230VAC 6W

ETH

(BACnet/IP)

Serial Port

(Not used)

DALI

Ethernet / BACnet/IP

(and IntesisBox configuration)

105mm

159mm

Autres manuels pour IBOX-BAC-DALI

Table des matières

Autres manuels IntesisBox Porte

IntesisBox

IntesisBox IBOX-ASCII-KNX Instructions de montage

IntesisBox

IntesisBox LG-AC-MBS-4 Manuel utilisateur

IntesisBox

IntesisBox LON-KNX Manuel utilisateur

IntesisBox

IntesisBox PA-AC-BAC-128 Instructions de montage

IntesisBox

IntesisBox IBOX-BAC-MBM Instructions de montage

IntesisBox

IntesisBox PA-AC-BAC-16 Instructions de montage

IntesisBox

IntesisBox KNX-Toshiba AC Manuel utilisateur

IntesisBox

IntesisBox HI-AC-KNX-16/64 Instructions de montage

IntesisBox

IntesisBox KNX Series Manuel utilisateur

IntesisBox

IntesisBox PA-AC-MBS-16 Instructions de montage

IntesisBox

IntesisBox ME-AC-KNX-1i Manuel utilisateur

IntesisBox

IntesisBox MBS-LON Manuel utilisateur

IntesisBox

IntesisBox KNX-Mitsubishi Heavy Industries AC Manuel utilisateur

IntesisBox

IntesisBox HI-AC-MBS-16 Instructions de montage

IntesisBox

IntesisBox KNX-Mitsubishi Electric G-50A Manuel utilisateur

IntesisBox

IntesisBox PA-AC-MBS-64 Manuel utilisateur

IntesisBox

IntesisBox SM-ACN-BAC-4 Instructions de montage

IntesisBox

IntesisBox KNX-LON Manuel utilisateur

IntesisBox

IntesisBox IBOX-MBS-MBUS Instructions de montage

IntesisBox

IntesisBox TO-RC-WMP-1 Manuel utilisateur

IntesisBox

IntesisBox HS-AC-BAC-16/64 Instructions de montage

IntesisBox

IntesisBox IBOX-BAC-MBRTU-100 Manuel utilisateur

IntesisBox

IntesisBox HI-AC-BAC-16/64 Manuel utilisateur

IntesisBox

IntesisBox IBKNXMEB0100000 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur