Intermec PR2 Manuel utilisateur

Product Name: Mobile Receipt Printer

Brand Name: Intermec

Model No: PR2/PR3

User’s Guide

Introduction

PR2/PR3 is a value entry performance mobile receipt printer. PR2 refers to a 2” Printer whereas PR3

corresponds to 3” Printer.

The differentiators of PR2/PR3 are:

a) Low system integration and management cost

b) Smallest Size

c) Lowest Weight

d) Fastest throughput

A PR3 printer is shown in Figure 1 (Top View)

Figure 1: A PR3 Printer (Top View)

The Front view of the printer is shown in Figure 2

Door Buttons

Tear Bar

LED Indicators

Power Button

Feed Button

LED Indicators

LED Name

LED Behavior and States

Ready-To-Work

Steady Blue = Printer is on and Ready-to-Work.

Flashing Blue: 50% duty cycle, 0.75 Hz = Printer

is on, but not ready to work or there is a critical

error.

Off = Printer is off or in deep sleep mode.

Connectivity

Flashes White: for 0.04 seconds for each packet

sent or received = Printer is communicating with

host (actively sending data)via USB, IrDA,

Bluetooth, or WiFi 802.11 radio.

Off = No data is being sent or received.

Battery

Off Charger

Off = Battery does not have a low charge.

Flashing Red: 25% duty cycle, 1 Hz = The

battery has a low charge.

On Charger

Steady Green = The printer is connected to

external power, and the battery is more than

95% charged.

Pulsing Green: (The output to the LED should be

driven with a pulse width modulated (PWM)

signal. The frequency used should be above the

human perception of any flicker. The difference

between PWM duty cycle changes should be

small enough so that there is no discernable

jump in output brightness. The duty cycle should

linearly change for 1.35 seconds to maximum

brightness, linearly change for 1.35 seconds to

minimum brightness and then remain off for 0.80

seconds. The resulting period of 3.50 seconds is

for a complete cycle from off to maximum

brightness and back to the off condition.) = The

printer is connected to external power and the

battery is charging and the battery is between

75% and 95% charged

Steady Red = the printer is connected to external

power and the battery is charging, and the

battery is between 0% and 75% charged

Flashing Amber at 50% duty cycle, 1 Hz = The

battery is out of charging temperature range.

Flashing Red at 50% duty cycle, 1 Hz = There is

a battery error.

Critical Error

Steady Red = Critical errors –cannot continue:

Door Open, Out of Paper, or Printhead is too hot

Off = No critical errors are present.

Magnetic Card Reader

Flashes Green 3 times in one second = Card

was read successfully

Flashes Red 1 time at 50% duty cycle, 1 Hz =

Card was read unsuccessfully

Off = Card reader is not being used.

Standard Communication Interfaces

There are various printer configurations based on the type of communication interfaces present in the

printer.

All configurations of the printer have USB communication.

Apart from USB, one of the following interfaces will be present

Bluetooth (FCC ID: EHA-INBT01; IC ID: 1223A-INBT01)

Wi-Fi

IrDA

Power Supply

The Printer is powered by a 2-cell battery pack with 8.4V, 1620mAh capacity.

Additionally, the battery is charged by using an external AC adapter which comes along with the printer

unit.

Print Test Page

To print a test page, press the feed button for a considerable duration (about 10 seconds) when the printer

is booting up.

Product operating temperature: -10 ~ 50 degree (discharge between -10 ~ 50 degree)

The battery charging mode to the operating temperature is only 40 degree.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Autres manuels pour PR2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intermec Imprimante

Intermec

Intermec PB3 Series Manuel utilisateur

Intermec

Intermec 681 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel

Intermec

Intermec EasyCoder 201II Manuel utilisateur

Intermec

Intermec EasyCoder PL4 Manuel utilisateur

Intermec

Intermec 3240 Manuel utilisateur

Intermec

Intermec EasyCoder PF4ci Instructions d'installation

Intermec

Intermec EasyCoder 301 Manuel utilisateur

Intermec

Intermec PB2 Series Manuel utilisateur

Intermec

Intermec EasyCoder C4 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Instructions d'installation

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec PW40A Manuel utilisateur

Intermec

Intermec EasyCoder PD41 Manuel utilisateur

Intermec

Intermec EasyCoder 501S Manuel utilisateur

Intermec

Intermec EasyCoder PC4 Manuel utilisateur

Intermec

Intermec PB2 Series Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder PF8 Manuel utilisateur

Intermec

Intermec EasyCoder PX4i Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder 4100 Manuel utilisateur

Intermec

Intermec EasyCoder 7421 Manuel utilisateur

Intermec

Intermec EasyCoder 7422 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur