Intelix DIGI-VGASD-WP-S Manuel utilisateur
Intelix DIGI-VGASD-WP-S
Installation Manual
Introduction
The Intelix DIGI-VGASD-WP-S active send balun transmits VGA video,
stereo audio, and IR or RS232 up to 350 feet over a single twisted pair cable.
The unit mounts into a double-gang, double-deep wallbox and features a local
monitor output.
When used with a compatible Intelix receive balun, the DIGI-VGASD-WP-S
provides 1600 x 1200 video performance and 20 Hz to 20 kHz, hi-fidelity
audio performance.
The unit requires power and includes a 5V power supply. Remote power may
be sent over 18 gauge stranded wire.
Installation
To install the Intelix DIGI-VGASD-WP-S balun, perform the following steps:
1. Identify the pin configuration of the baluns and RJ45 connectors on the
twisted pair cabling. To eliminate crosstalk, the pin configuration must
follow the EIA/TIA 568B standard. Please ensure that wiring is straight-
through.
2. Power-off all connecting audio, video, and control equipment.
3. Verify the wallbox the DIGI-VGASD-WP-S send balun will be mounted
into is double-gang and double-deep.
4. Connect the DIGI-VGASD-WP-S send balun to the twisted pair cable.
Connect the power supply.
5. Mount the DIGI-VGASD-WP-S send balun into the double-gang wallbox.
6. Connect a compatible receive balun to the twisted pair cable which is
connected to the DIGI-VGASD-WP-S send balun. Connect the power
supply.
7. Connect the DIGI-VGASD-WP-S send balun to the VGA output of the
video source, the audio output of the audio source, and an IR or RS232
control source. If desired, connect a local monitor.
Note the DIGI-VGASD-WP-S does not support IR and RS232
simultaneously. If both signals are connected, IR will take precedence
over RS232.
Compatible Intelix receive baluns include:
DIGI-VGASD-WP-R wallplate receive balun
DIGI-VGASD-R modular receive balun
8. Connect the compatible receive balun to the VGA input of the video
destination, the audio input of the audio destination, and an IR or RS232
control destination.
9. Connect the 5 VDC power supply to the DIGI-VGASD-WP-S.
10. Power-on all connecting video, audio, and control equipment.
11. Verify picture quality. If necessary, adjust the signal using the blue, green,
and red dials on the receive balun.
Remote Power Cabling Specifications
18 gauge cable max distance: 200 feet
24 gauge cable max distance: 43 feet
Minimum voltage required: 4.5 VDC
Maximum amperage required: 220 milliamps
Warning! Do not use any IR receiver (eye) or IR emitter other than those
sold exclusively for the DIGI-VGASD series of products to prevent
damage to the balun. Using 12V-
b
ased IR components may permanently
damage the IR circuitry of the product and void the warranty.
Required IR Emitter: Intelix DIGI-VGASD-IREMT
Required IR Receiver: Intelix DIGI-VGASD-IREYE
Example System
Troubleshooting
Symptom Causes Possible Solutions
No signal No continuity in
video link
Verify cable continuity between pairs of
baluns.
Verify the max distance has not been
exceeded.
Verify the audio, video, and control
cables between the equipment and
hardware are connected and pass signal.
No signal Power off Check power supplies of video
equipment.
Verify the LEDs on both the send and
receive units are illuminated.
No signal Improper
connection or
swapped pairs
Check that baluns are connected to
correct video inputs and outputs.
Verify both ends of the twisted pair
cable conform to the EIA 568B crimp
pattern.
Unusual colors
Rolling signal
Horizontal
video bars
Improper
grounding or
cable type
Verify the source and destination
devices are grounded. Different
electrical circuits may cause a voltage
differential on the building’s electrical
ground plain. The video display or
source deceive may need to be
grounded.
No control Simultaneous
RS232 and IR
Verify only IR or RS232 are being used.
Background
pattern
EMI interference Identify possible radiating frequency
sources (i.e.; wireless LANs, switching
power supplies) and isolate them.
Replace any unshielded twisted pair
cable with shielded twisted pair cable.
Technical Specifications
Video Bandwidth 300 MHz
Max Resolution 1600 x 1200
Max Distance 350 feet
Audio Frequency Response 20 Hz to 20 kHz
Enclosure Metal
Mounting Double-gang, double-deep wallbox
Control IR or RS232; IR takes precedence when
both are connected
Max Distance of AV Cables 6 feet
Status Front panel power LED
Power 5 VDC @ 0.5A
Power Cabling Intelix recommends 18 gauge, two
conductor
Dimensions Faceplate: 4.5” x 4.5”
Rear: 2.75” deep x 3.63” wide x 2.5” tall
Faceplate Color White
Temperature Operating: 0° to 55°C
Storage: -20° to 85°C
Humidity: up to 95%
Shipping Weight 3.0 lbs.
Warranty 2 years
Compliancy CE, RoHS
Included Accessories One (1) 5VDC power supply
Ordering Information DIGI-VGASD-WP-S
*Distances, picture and audio quality may be affected by cable grade,
cable quality, source and destination equipment, RF and electrical
interference, and cable patches. Intelix specifications are based on
straight-through cabling with standard-grade Cat 5.
Intelix LLC
2222 Pleasant View Road Phone: 608-831-0880
Middleton, WI 53562 Toll-Free: 866-4-MATMIX
www.intelix.com [email protected]
Table des matières
Autres manuels Intelix Extenseur
Intelix
Intelix AVO-A2 Manuel utilisateur
Intelix
Intelix VGA2-HR Manuel utilisateur
Intelix
Intelix VGA2-UHR Manuel utilisateur
Intelix
Intelix INT-IPEX1001 Manuel utilisateur
Intelix
Intelix DIGI-HD-COAX2 Manuel utilisateur
Intelix
Intelix DIGI-HD60C Manuel utilisateur
Intelix
Intelix AvoCat AVO-V1A2 Manuel utilisateur
Intelix
Intelix DIGI-BSR-4K Manuel utilisateur
Intelix
Intelix DIGI-USB2-4P Manuel utilisateur
Intelix
Intelix DIGI-USB2 Manuel utilisateur
Intelix
Intelix DIGI-USB2 Manuel utilisateur
Intelix
Intelix DIGI-HDX Manuel utilisateur
Intelix
Intelix AVO-A2-MINI-WP-F Manuel utilisateur
Intelix
Intelix DIGI-HD-COAX Manuel utilisateur
Intelix
Intelix DIGI-HDMI-4X2 Manuel technique
Intelix
Intelix DIGI-HD70 Manuel utilisateur
Intelix
Intelix DIGI-HDE Manuel utilisateur
Intelix
Intelix DIGI-HD60-WP-S Manuel utilisateur
Intelix
Intelix DIGI-BSR-4K-BSTK Manuel utilisateur
Intelix
Intelix AVO-A2-MINI-WP Manuel utilisateur
