Intelix DIGI-USB2-4P Manuel utilisateur

DIGI-USB2-4P Installation Guide

Important notice:

• Do not attempt to disassemble or alter the housing. There are no user-serviceable

parts inside the unit. Doing so will void your warranty.

• To minimize the possibility of equipment damage from electrostatic discharge (ESD),

all source and destination equipment must be powered off during installation.

• Do not connect the device to a telecommunication outlet wired to unrelated

equipment. Doing so may damage the unit or any connected equipment. Ensure all

connected twisted pair cabling is straight-through (point-to-point).

• Allow proper ventilation to reduce the risk of thermal failure.

The Intelix DIGI-USB2-4P extends computer USB 1.1 and USB 2.0

signals up to 100m (330 ft) over twisted pair cabling to four remote

devices.

The DIGI-USB2-4P utilizes inexpensive twisted pair cabling and

has a throughput of up to 480Mbps. The DIGI-USB2-4P is perfect

for keyboard and mouse extension, remote data ports, up to 4

USB hubs, security applications and interactive white board

applications.

Host Side Connections

Client Side Connections

12 3 4

A B C D

1. Status LEDs

• Power: Solid blue when power is applied

• Link: Solid green when link is present between extenders

• Host: Solid green when connected to host PC; flashes green when in a

suspended state

• Activity: Flashes amber when transmitting data; off when in extenders

are in a suspended state

2. 5V DC Power Input — Only needed if host PC cannot provide 500mA of current

to USB port

3. USB Type B Port to PC

4. Link Port to Extender

A. USB Type A Port to Device(s) with LED

• Solid green when device is present and operating normally

• Off when device is in suspend mode or extender is powered off

• Solid orange when an overcurrent condition (greater than 500 mA of

current draw) is detected

B. Status LEDs

• Power: Solid blue when power is applied

• Link: Solid green when link is present between extenders

• Host: Solid green when connected to host PC; flashes green when in a

suspended state

• Activity: Flashes amber when transmitting data; off when in extenders

are in a suspended state

C. 5V DC Power Input

D. Link Port to Extender

Instructions

1. Verify all components included with the extender set are present

before installation.

2. Connect the included USB cable between the computer and the Host

device.

3. Connect the remote device(s) to the client extender.

4. Connect Category 5e or greater twisted pair cable with RJ45

connectors between the Host and the Client extenders. TIA/EIA-568B

straight-through wiring connections must be used.

5. Connect the included power supply to the Client extender.

6. Verify proper operation of the extended USB device.

Included Accessories

• Power supply

• USB Type A to USB Type B cable

TIA/EIA-568B

Orange/White

Orange

Green/White

Blue

Blue/White

Green

Brown/White

Brown

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

1 8

Twisted Pair Wiring

Use TIA/EIA-568B wiring for Category

6 connections between transmit and

receive units.

Troubleshooting Tips

Symptom Possible Solutions

• USB is not functioning

• USB Port LED is off

• Verify that both ends of the twisted pair cables use

T568B crimp pattern.

• Verify the power LEDs on both the send and receive units

are brightly illuminated.

• Verify the power supply is connected to either the client

extender.

• USB is not functioning

• USB Port LED is on

• Verify USB cables at local and remote USB ports are

operational.

• Verify USB device works directly attached to PC.

• Verify the USB device driver is installed and working.

• USB is not functioning

• Overcurrent notification

(orange LED on USB port)

• Verify that the maximum distance has not been exceeded.

• Power cycle the client extender. Allow time for the

system to discharge; 30 seconds will be adequate.

rev 150515

8001 Terrace Ave, Ste 201

Middleton, WI 53562

608-831-0880

supportlibav@libav.com

Host Input/Output Connections

USB Input One (1) USB Type B Receptacle

Link Output One (1) 8P8C Connector (RJ45 style)

5V DC Power One (1) Barrel (5.5 mm OD; 1.7 mm ID)

Client Input/Output Connections

USB Outputs (500 mA max current) Four (1) USB Type A Receptacles

Link Input One (1) 8P8C Connector (RJ45 style)

5V DC Power One (1) Barrel (5.5 mm OD; 1.7 mm ID)

USB Performance

Maximum Distance 100 m (328 ft) over Category 5e or greater cable

USB Device Support High-speed devices (USB 2.0) - up to 480 Mbps

Full-speed devices (USB 2.0 & 1.1) - up to 12 Mbps

Low-speed devices (USB 2.0 & 1.1) - up to 1.5 Mbps

USB Hub Support Any single chain can include up to 4 USB hubs plus one DIGI-USB2-4P.

USB Host Support xHCI (USB 3.0) at USB 2.0 speed, EHCI (USB 2.0) and OHCI/UHCI (USB 1.1)

Maximum USB Devices Supported Up to 15 USB devices or 4 USB hubs with 11 USB devices.

Chassis and Environmental

Enclosure Material Anodized Aluminum

Enclosure Dimensions (H x W x D) 26 mm x 100 mm x 76 mm (1.02 in x 3.94 in x 2.99 in)

Shipping Weight 0.9 kg (2.0 lbs)

Operating Temperature 0° to +50° C (+32° to +122° F)

Operating Humidity 10% to 90%, Non-condensing

Storage Temperature -20° to +70° C (+14° to +158° F)

Storage Humidity 10% to 85%, Non-condensing

Power and Regulatory

Power Supply Input 100V-240VAC / 50-60 Hz / 0.6A

Power Supply Output 5VDC / 3.0A

Power Consumption 15 watts (max)

ESD Protection ±15 kV

Product Regulatory FCC, CE, IC, RoHS

Power Supply Regulatory UL, CUL, CE, PSE, GS, RoHS

Other

Warranty 2 years

Diagnostic Indicators (Host Side) Power, Host, Link, Activity

Diagnostic Indicators (Client Side) Power, Host, Link, Activity, USB Port Status

Included Accessories Wall Mount Power Supply, USB Type A to USB Type B cable, Installation

Guide

Distances and picture quality may be affected by cable grade, cable quality, source and

destination equipment, RF and electrical interference, and cable patches.

Technical Specifications

Autres manuels Intelix Extenseur

Intelix

Intelix DIGI-HD-IR3 Manuel utilisateur

Intelix

Intelix INT-IPEX1001 Manuel utilisateur

Intelix

Intelix int-hd70 Manuel utilisateur

Intelix

Intelix DIGI-HD-COAX Manuel utilisateur

Intelix

Intelix DIGI-HDE Manuel utilisateur

Intelix

Intelix DIGI-USB2 Manuel utilisateur

Intelix

Intelix AVO-A2-MINI-WP Manuel utilisateur

Intelix

Intelix DIGI-BSR-4K Manuel utilisateur

Intelix

Intelix DIGI-BSR-4K-BSTK Manuel utilisateur

Intelix

Intelix AVO-A2-MINI-WP-F Manuel utilisateur

Intelix

Intelix DIGI?HD?COAX Manuel utilisateur

Intelix

Intelix DIGI-VGASD-WP-S Manuel utilisateur

Intelix

Intelix AVOCat AVO-SVA2-WP Manuel utilisateur

Intelix

Intelix AVO-SVA2 Manuel utilisateur

Intelix

Intelix VGA2-UHR Manuel utilisateur

Intelix

Intelix AVO-V1A2-F Manuel utilisateur

Intelix

Intelix DIGI-HDUSB Manuel utilisateur

Intelix

Intelix DIGI-HD60-WP-S Manuel utilisateur

Intelix

Intelix USB 2.0 DIGI-USB2 Manuel utilisateur

Intelix

Intelix DIGI-HD70 Manuel utilisateur

Intelix

Intelix DIGI-USB2 Manuel utilisateur

Intelix

Intelix VGA2-HR Manuel utilisateur

Intelix

Intelix DIGI-HD60C Manuel utilisateur

Intelix

Intelix AVO-A2 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur