Intel P4308CP4MHEN Manuel utilisateur

Thank you for buying an Intel® Server System. The following information will help you

assemble your Intel®Server System and install components.

If you are not familiar with ESD [Electrostatic Discharge] procedures used during

system integration, see the complete ESD procedures described in your Service Guide.

This guide and other supporting documents are located on the web at:

http://www.intel.com/support.

Intel® Server System P4000CP Family

Quick Installation User's Guide

G43150-001

(This page is intentionally left blank.)

Table of Contents

General Installation Process ........................................................................................................ 3

System Overview .............................................................................................................................. 1

Preparing the System ....................................................................................................... 3

Remove the Side Cover ................................................................................................... 3

Remove the Air Duct ......................................................................................................... 3

Install the Processor(s) .................................................................................................... 3

Install Active Heat Sink(s) ............................................................................................. 4

Install DIMM Memory Modules ..................................................................................... 5

Install Tool-less CD-ROM or DVD-ROM Drive ........................................................ 5

Install Hard Drive ................................................................................................................. 6

Install PCI Card Assembly ............................................................................................... 7

Install Expander Card (optional) .................................................................................. 8

Install Alternate Serial Port (optional) ..................................................................... 8

Install Intel® Remote Management Module 4 NIC (optional) ....................... 8

Install Intel® RAID Smart Battery (optional) ......................................................... 9

Install Second Power Supply Module (optional) ................................................. 9

Rack Mount Conﬁguration (optional) ....................................................................... 9

Install Feet (pedestal only) ............................................................................................ 9

Install Air Duct ................................................................................................................... 10

Install Side Cover .............................................................................................................. 10

Finishing Up ......................................................................................................................... 10

Install Software ................................................................................................................. 10

HDD Cage Cable Connection ...................................................................................... 11

Front Panel Controls and Indicators ...................................................................... 12

Cable Routing Diagram .................................................................................................. 12

Reference ............................................................................................................................................ 11

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://www.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Warning

Installation and service

of this product to be

performed only by

qualified service personnel

to avoid risk of injury from

electrical shock or energy

hazard.

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Flat Blade

screwdriver

Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the

Thermal Operation and Conﬁguration Requirements

To keep the system operating within supported maximum thermal limits, the system must meet the following operating and

configuration guidelines:

Intel® Server System P4000CP Family Product Configuration

= Configuration Feature

8 x 3.5"

Hot Swap

8 x 2.5"

Hot Swap

Hard DriveSystem Fan

One

Fixed

550W

Two

Hot Swap

750W

RKSATA8

RKSAS8

Power Supply

P4308CP4MHEN

P4308CP4MHGC

P4208CP4MHGC

Intel® Server

System

Intel®

RAID

C600

Upgrade

Key

Five

Hot Swap

System

Fans

(80 x 38 mm)

One

Fixed

PCI Zone

Fan

(120 x 38 mm)

One

Fixed

CPU Zone

Fan

(120 x 38 mm)

Thermal Operation and Conﬁguration Requirements

To keep the system operating within supported maximum thermal limits, the system must meet the following operating and configuration

guidelines:

• Ambient in-let temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time. Doing so

may affect long term reliability of the system.

•The CPU-1 processor and CPU heatsink must be installed.

•DIMM Population on CPU-1: Install DIMMs in order; Channels A, B, C, and D. Start with 1st DIMM slot (blue) on each

channel.

• DIMM Population on CPU-2: Install DIMMs in order; Channels E, F, G, and H. Start with 1st DIMM slot (blue) on each

channel.

•All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied drive blank.

•The air duct must be installed at all times.

•In single power supply configurations, the second power supply bay must have the supplied filler blank installed at all times.

•The system top-cover must be installed at all times.

System Overview

Intel® Server System P4308CP4MHGC

System Features and Components

750-W Hot Swap Power Supply (Two)

I/O Ports

A Kensington* Cable Lock Mounting Hole

PCI Add-in Board Slot Covers

AC Input Power Connector (Two)

Alternate Serial Port Knockout

Alternate RMM4 Knockout

Padlock Loop

Alternate RMM4 Knockout

Hot-swap System Fan

Heatsink

O8 x 3.5" Hot-swap HDD Cage

Front Control Panel

5.25" Peripheral Bays

Server Board

PPCI retainer

NOTE: Airduct is not shown.

Intel® Server System P4308CP4MHEN

System Features and Components

550-W Fixed Power Supply

I/O Ports

A Kensington* Cable Lock Mounting Hole

PCI Add-in Board Slot Covers

AC Input Power Connector

Serial Port Knockout

Alternate RMM4 Knockout

Padlock Loop

Alternate RMM4 Knockout

Front Control Panel

5.25" Peripheral Bays

Fixed System Fan

PCI retainer

Heatsink

Server Board

8 x 3.5" Hot-swap HDD Cage

NOTE: Airduct is not shown.

System Overview

8 x 3.5" Hot-swap HDD Cage

0123

4567 01234567

Hot Swap Hard Drive

Bay Options and

HDD Numbering

8 x 3.5" Hot-Swap Drive Cage

8 x 2.5" Hot-Swap Drive Cage

Intel® Server System P4208CP4MHGC

System Features and Components

750-W Hot Swap Power Supply (Two)

I/O Ports

A Kensington* Cable Lock Mounting Hole

PCI Add-in Board Slot Covers

AC Input Power Connector (Two)

Alternate Serial Port Knockout

Alternate RMM4 Knockout

Padlock Loop

Alternate RMM4 Knockout

Hot-swap System Fan

Heatsink

Front Control Panel

5.25" Peripheral Bays

8 x 2.5" Hot-swap HDD Cage

Server Board

PEMI Filler

NOTE: Airduct is not shown.

QPCI retainer

General Installation Process

The installation instructions in this section are for general components of Intel® Server System

P4000MCP family, but the illustrations are based on the Intel® Server System P4308CP4MHEN.

Minimum Hardware Requirements

■Processor

■Heat Sink

■Memory

■Hard Disk Drives

■Power

■Air Duct

To avoid integration difficulties and possible damage to your system,

make sure you have components from each category below.

Preparing the System

Observe normal ESD (Electrostatic Discharge) procedures.

Place your Intel®Server System on a flat anti-static

surface to perform the following integration procedures.

Observe ESD procedures before reaching inside to make

server board connections or install components.

3Remove the Air Duct

ARemove the air duct.

4Remove Processor Heatsink(s)

The heatsink is attached to the server

board / processor socket with captive fasteners.

Lift the heatsink straight up.

Proceed to screw 2 and loosen it by

giving it two rotations and stop.

Similarly, loosen screws 3 and 4.

Repeat steps A and B by giving each

screw two rotations each time until

all screws are loosened.

Using a #2 Phillips* screwdriver,

start with screw 1 and loosen it

by giving it two rotations and stop.

(IMPORTANT: Do not fully loosen.)

CAUTION: The heatsink has thermal interface material (TIM) on

the underside of it. Use caution so that you do not damage the

thermal interface material. Use gloves to avoid sharp edges.

Using a #2 Phillips* screwdriver, loosen the four

screws located on the heatsink corners in a

diagonal manner using the following procedure:

OPEN 1st

CLOSE 1st

NO CPU

Processor

Socket

5Install the Processor(s)

CLOSE 1st

OPEN 1st

REMOVE

OPEN 1st

NO CPU

OPEN 1st

CLOSE 1st

NO CPU

A. Open the Socket Lever

BRepeat step A to release

the lever on the other

side.

Push down the lever

handle on the OPEN 1st

side and away from the

socket to release it.

NOTE: Release

the levers in the

order as shown.

Remove the Side Cover

Remove the screws.

Note:

A non-skid surface or a

stop behind the chassis

may be needed to prevent

the chassis from sliding on

your work surface.

Slide the side cover back and lift

the cover outward to remove it.

General Installation Process

6Install Heat Sink(s)

Get heat sink from the shipping position.

Remove the protective film on the TIM if present.

Securely re-tighten each fastener again in the same order as performed in Step E.

Using a #2 Phillips* screwdriver, finger-tighten each fastener diagonally,

according to the numbers shown.

Align heat sink fins to the front and back of the chassis for correct airflow.

Airflow goes from front-to-back of chassis.

The heat sink has four captive fasteners and should be tightened using the following procedure:

CAUTION: The heat sink has thermal interface

material (TIM) on the underside of it. Use caution so

that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

OPEN 1st

CLOSE 1st

TIM

Processor

Socket

AIRFLOW

Chassis Front

CAUTION:

Do not

over-tighten

fasteners.

Save the

protective

cover.

Install the Processor(s) ... continued

D. Remove the Cover

Press the cover to

remove it.

Carefully lower the load plate over

the processor.

E. Close the Load Plate

Push down on the locking lever on the CLOSE 1st side.

F. Latch the Locking Lever

BSlide the tip of the lever under the notch in the load plate. Make sure

the load plate tab engages under the socket lever when fully closed.

CRepeat the steps to latch the locking lever on the other side.

OPEN 1st

CLOSE 1st

REMOVE

CLOSE 1st

OPEN 1st

CLOSE 1st

NOTE: Latch the levers in

the order as shown.

Install the Processor(s) ... continued

OPEN 1st

CLOSE 1st

NO CPU

B. Open the Load Plate

BOpen the load plate all the way.

Press the locking lever slightly to raise the

load plate.

C. Install the Processor

Take the processor out of the

box and remove the

protective shipping cover.

CAUTION: When unpacking

a processor, hold by the

edges only to avoid touching

the gold contact pins.

Save the

protective

cover.

CAUTION: The underside

of the processor has

components that may damage

the socket pins if installed

improperly.

Processor must

align correctly

with the

socket

opening before

installation.

DO NOT DROP

processor into socket!

Components

Note location of gold key at

corner of processor.

Orient the processor with the socket so

that the processor cutouts match the

four orientation posts on the socket.

General Installation Process

7Install DIMM Memory Modules

DDR3 DIMM Memory Identiﬁcation:

DIMM

notch and

socket

bump must

align as

shown.

Other

Memory

DDR3

This server board supports up to 16 DDR3 800/1066/1333/1600 ECC

UDIMM/RDIMM/LRDIMM.

CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures

to avoid possible damage to system components.

Memory sizing and configuration is supported only for qualified DIMMs approved by Intel. For a list of

supported memory, see the tested memory list at http://serverconfigurator.intel.com/default.aspx

Memory Type: Minimum of one 1 GB, DDR3 800/1066/1333 MHz ECC UDIMM/RDIMM/LRDIMM.

Install DIMM Memory Modules ... Continued

To Install DIMMs:

Open both DIMM socket levers.

Note location of alignment notch.

CAUTION: Avoid touching contacts

when handling or installing DIMMs.

IMPORTANT! Visually check that each latch is fully closed and correctly engaged with each DIMM edge slot.

Push down firmly on the DIMM until it snaps into place and both levers close.

Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.

8Install Tool-less CD-ROM or DVD-ROM Drive

Attach slides to the DVD or CD-ROM drive

by pressing the slides firmly into the side

dimples on the DVD or CD-ROM drive.

Get the slides from the

chassis side.

Insert the drive/slide assembly

into the device bay until the

slides lock into place.

Press the release latch and use

the finger holes to Pull out the

EMI shield.

Finger Holes

C1DIMM C2 D1 D2 B2DIMM B1 A2 A1

E1DIMM E2 F1 F2 H2DIMM H1 G2 G1

General Installation Process

Install Hard Drive

2.5" Hot-Swap Hard Drive Carrier (For system with 2.5" hot-swap hard drive bay only)

Open the Hot-swap door and

remove the drive carrier by

pressing the green button and

opening the lever.

Slide the carrier out.

2.5" HDD

Remove the four screws securing the

plastic retention device to the 2.5"

HDD carrier.

Disengage the plastic retention device

from the HDD carrier slides by

pulling the slides.

Remove the plastic retention device

from the 2.5" HDD carrier.

Install the hard disk drive using the

four screws as shown. Make Sure the

connector end of the drive matches

the backplane connector.

CAUTION: If you don’t install all

drives, empty drive bays must

be occupied by carriers with

plastic drive blank provided to maintain

proper system cooling.

With the lever open, insert the

hard disk drive assembly into the

cage opening and push until the

locking lever engaged.

Push in the lever to lock it into

place, then close the door.

Install Hard Drive ... Continued

3.5" Hot-Swap Hard Drive Carrier (For system with 3.5" hot-swap hard drive bay only)

Open the Hot-swap door and

remove the drive carrier by

pressing the green button and

opening the lever.

Slide the carrier out.

Remove the four screws securing the

HDD interface bracket and remove the

HDD interface bracket.

Install the hard disk drive using the

same four screws as shown. Make

sure the connector end of the drive

matches the backplane connector.

CAUTION: If you don’t install all

drives, empty drive bays must

be occupied by carriers with

plastic drive blank provided to maintain

proper system cooling.

With the lever open, insert the

hard disk drive assembly into the

cage opening and push until the

locking lever engaged.

Push in the lever to lock it into

place, then close the door.

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

3.5´´ HDD

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intel Serveur

Intel

Intel MFSYS25 - AXXPSU 1000W Power Supply Module Manuel utilisateur

Intel

Intel R200LH2 Manuel utilisateur

Intel

Intel S5500BC Mode d’emploi

Intel

Intel R2000LH2 Manuel utilisateur

Intel

Intel S2600CW Manuel utilisateur

Intel

Intel SERVER SYSTEM SR2500AL Manuel utilisateur

Intel

Intel D40AMP Series Manuel utilisateur

Intel

Intel AXX6DRV3GEXP Manuel utilisateur

Intel

Intel SR1500 - AXXMINIDIMM DDR-2 RAID Controller Cache... Manuel utilisateur

Intel

Intel SR1690WB - Server System - 0 MB RAM Manuel utilisateur

Intel

Intel STCK1A32WFC Manuel utilisateur

Intel

Intel MFSYS25 - AXXPSU 1000W Power Supply Module Manuel utilisateur

Intel

Intel H2000WP Manuel utilisateur

Intel

Intel JBOD 2000 Family Manuel utilisateur

Intel

Intel H2000WP Manuel utilisateur

Intel

Intel SRPL8 Manuel utilisateur

Intel

Intel R2000SC Manuel utilisateur

Intel

Intel R1000WF Series Guide de configuration rapide

Intel

Intel SR1530CL - Server System - 0 MB RAM Manuel utilisateur

Intel

Intel SR870BN4 - Server Platform - 0 MB RAM Manuel utilisateur

Intel

Intel M50CYP1UR Series Manuel utilisateur

Intel

Intel S7000FC4UR - Server System - 0 MB RAM Manuel utilisateur

Intel

Intel R2000WF series Guide de configuration

Intel

Intel AP450GX MP Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur