Intel G41 Express Chipset Manuel utilisateur

USER'S MANUAL

Intel G41 Express Chipset

Intel ICH7 Chipset

Based

M/B for Intel LGA 775

Core Processor Family

No. G03-TI41M-F

Rev: 1.0

Release date: May, 2011

Trademark:

* Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

Environmental Safety Instruction

zAvoid the dusty, humidity and temperature extremes. Do not place the product in any

area where it may become wet.

z0 to 40 centigrade is the suitable temperature. (The figure comes from the request of

the main chipset)

zGenerally speaking, dramatic changes in temperature may lead to contact malfunction

and crackles due to constant thermal expansion and contraction from the welding

spots’ that connect components and PCB. Computer should go through an adaptive

phase before it boots when it is moved from a cold environment to a warmer one to

avoid condensation phenomenon. These water drops attached on PCB or the surface

of the components can bring about phenomena as minor as computer instability

resulted from corrosion and oxidation from components and PCB or as major as short

circuit that can burn the components. Suggest starting the computer until the

temperature goes up.

zThe increasing temperature of the capacitor may decrease the life of computer. Using

the close case may decrease the life of other device because the higher temperature in

the inner of the case.

zAttention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. To minimize pollution

and ensure environment protection of mother earth, please recycle.

CHAPTER 1 INTRODUCTION OF INTEL G41 MOTHERBOARD SERIES

1-1 FEATURES OF MOTHERBOARD .............................................................................1

1-1.1 SPECIAL FEATURES OF MOTHERBOARD...............................................2

1-2 ITEM CHECKLIST .....................................................................................................2

1-3 SPECIFICATION.........................................................................................................3

1-4 LAYOUT DIAGRAM ..................................................................................................4

CHAPTER 2 HARDWARE INSTALLATION

2-1 HARDWARE INSTALLATION STEPS.......................................................................5

2-2 JUMPER SETTING......................................................................................................5

2-3 CPU INSTALLATION..................................................................................................6

2-4 MEMORY INSTALLATION.........................................................................................7

2-5 EXPANSION CARD INSTALLATION.........................................................................8

2-5.1 EXPANSION SLOT .......................................................................................8

2-5.2 PROCEDURE FOR EXPANSION CARD INSTALLATION..........................8

CHAPTER 3 CONNCTORS AND HEADERS

3-1 I/O BACK PANEL CONNECTORS.............................................................................9

3-2 MOTHERBOARD INTERNAL CONNECOTRS..........................................................9

3-3 HEADERS ...................................................................................................................11

CHAPTER 4 USEFUL HELP

4-1 HOW TO UPDATE BIOS ............................................................................................14

4-2 TROUBLE SHOOTING...............................................................................................14

APPENDIX I ...............................................................................................................15

TABLE OF CONTENT

Chapter 1

Introduction of Intel G41 Motherboard Series

1-1 Features of Motherboard

The Intel G41 chipset motherboard series are based on the latest Intel G41 Express

Chipset and Intel ICH7 Chipset technology which supports the innovative 65nm and

90nm Intel®Core 2 Quad, Intel®Core 2 Duo®(Code Name: Conroe) Processor, Intel®

Pentium®Dual Core Processor, Celeron®Dual Core Processor and Celeron®400

Processor with Intel®Hyper-Threading Technology and fully supports the future 45nm

processors. The motherboard is optimized to deliver innovative features and

professional desktop platform solution for those who demand the best experience of

personal computing.

The motherboard series implement Intel G41 Express Chipset which supports Front

Side Bus 1333MHz of data transferring. The motherboard series support dual-channel

DDRIII 1066/1333MHz RAM Module expandable to 4GB. The motherboards are

embedded with ICH7 chipset of four serial ATA2 interface of 3Gb / s data transfer rate

for four serial ATA devices.

The G41 motherboard series offer one PCI-Express x16 graphics slot of 8Gbyte/sec

data transfer rate at each relative direction which gets 7 times of bandwidth more than

AGP 8X and up to 16Gbyte/sec peak concurrent bandwidth at full speed to guarantee

the ultimate GPU computing performance. One 32-bit PCI slot also enriches

connectivity for the I/O of peripherals. The motherboards are designed of tackling the

profuse multimedia requirements nowadays.

The motherboards provide 10/100 Ethernet LAN function by using the PCI-E megabit

LAN Chip. The embedded 6-CH HD Audio chip is fully compatible with Sound Blaster

Pro standards providing 6-CH HD audio CODEC offers you with the home cinema

quality and satisfying software compatibility.

Embedded USB controller as well as capability of expanding to 8 USB 2.0 functional

ports delivering 480Mb/s of rich connectivity, these motherboards meet the demands

of future USB peripherals which are also equipped with hardware monitor function on

system to monitor and protect your system and maintain your non-stop business

computing.

Some special features---CPU Thermal Throttling/CPU Vcore Output OC-CON in

this motherboard are designed for power user to use the over-clocking function in

more flexible ways. But please be caution that the over-clocking maybe causes the

fails in system reliabilities. This motherboard provides the guaranteed performance

and meets the demands of the next generation computing. But if you insist to gain

more system performance with variety possibilities of the components you choose,

please be careful and make sure to read the detailed descriptions of these value

added product features, please get them in the coming section.

1-1.1 Special Features of Motherboard

CPU Thermal Throttling Technology--- CPU Overheat Protection Technology

To prevent the increasing heat from damage of CPU or accidental shutdown while at

high workload, the CPU Thermal Throttling Technology will force CPU to enter

partially idle mode from 87.5% to 12.5% according to preset CPU operating

temperature in BIOS (from 40℃to 90℃). When the system senses the CPU

operating temperature reaching the preset value, the CPU operating bandwidth will be

decreased to the preset idle percentage to cool down the processor. When at

throttling mode the beeper sound can be optionally selected to indicate it is in working.

CPU Smart Fan—Noise Management System

It’s never been a good idea to gain the performance of your system by sacrificing its

acoustics. CPU Smart Fan Noise Management System is the answer to control the

noise level needed for now-a-day’s high performance computing system. The system

will automatically increase the fan speed when CPU operating loading is high, after

the CPU is in normal operating condition, the system will low down the fan speed for

the silent operating environment. The system can provide the much longer life cycle

for both CPU and the system fans for game use and business requirements.

CPU Output Solid Capacitors---High-polymer Solid Electrolysis Aluminum

Capacitors

CPU Vcore Input and Output of the motherboard adopts OC-CON solid capacitors to

make it possible for motherboard to work from 55 degrees Centigrade below zero to

125 degrees centigrade. OC-CON capacitors possess superior physical

characteristics to prolong product life ten times than corresponding motherboard

without capacitors every time working temperature increases 20 degrees. Life of

product of motherboard with solid capacitors declines only 10% of those without solid

capacitors as well under same conditions.

1-2 Item Checklist

5Motherboard

5User’s manual

5DVD for motherboard utilities

5SATA cable

5Back panel

1-3 Specification

Spec Description

Design zMicro ATX form factor

Chipset zIntel G41 Memory Controller Hub (MCH) Chipset

zIntel 82801GB I/O Controller Hub (ICH7) Chipset

CPU Socket

(LGA775 )

zSupports the innovative 65nm and 90nm Intel® Celeron®

400, Intel® Celeron® Dual Core, Pentium®Dual Core

Processor, Intel®Core 2 Quad, Intel®Core 2 Duo®(Code

Name: Conroe) Processor with Intel®Hyper-Threading

Technology and fully supports the future 45nm processors

zSupport FSB Frequency 1333 MHz

zSuggest the power of the CPU should below 65W

Memory Slot z240-pin DDRIII RAM module socket x 2 supporting two

DDRIII1066/1333 MHz RAM Module expandable to 4GB

zSupport dual-channel function

Expansion Slots zPCI-Express x16 slot 1pcs.

z32-bit PCI slot 1pcs

Serial ATA2 zSupport four serial ATA2 ports

LAN Chip

zIntegrated PCI-E 10/100 LAN chip

zSupport Fast Ethernet LAN function of providing 10Mb /

100Mb data transfer rate

HD Audio Chip z6-channel HD Audio Codec integrated

zAudio driver and utility included

BIOS zAMI 8MB Flash ROM

Multi I/O

zPS/2 keyboard and PS/2 mouse connectors

zVGA Connector x1

zUSB 2.0 connector x 4

zRJ-45 LAN connector x1

zAudio connector x1 (Line-in, Line-out, MIC)

zFront panel audio header x1

zHDMI-SPDIF header x1

zFront panel header x1

zPWRLED header x1

zSpeaker header x1

zSerial Port header x1

zUSB 2.0 headers x2

1-4 Layout Diagram

RJ-45 LAN Port

PS/2 Mouse Port

PS/2 Keyboard Port

Line-IN

Line-OUT

MIC-IN

USB Ports

VGA Port

ATX 12V Power

Connector

ATX Power

Connector

CPU Socket

Intel 82801GB

ICH Chipset

DDRIII

DIMMx2

6-CH

HD Audio Codec

32-bit PCI Slot

Serial Port Header

KB／MS Power ON

Jumper (JP1)

USB Por

s SYSFAN1

Front Panel

Audio Heade

Megabit LAN Chip

Serial-ATA2

Connector (SATA1, 2)

CPU FAN

VGA Port

RJ-45 Over USB Ports

PCI Express x16 Slot

Intel G41Express

Chipset

PS2 KB/Mouse

Ports

USB Headers

JBAT

6-CH

Audio Connector

Serial-ATA2

Connector (SATA3, 4)

Power LED &

Heade

Front Panel Header

JP2

HDMI-SPDIF Header

Chapter 2

Hardware Installation

WARNING! Turn off your power when adding or removing expansion cards or

other system components. Failure to do so may cause severe

damage to both your motherboard and expansion cards.

2-1 Hardware Installation Steps

Before using your computer, you had better complete the following steps:

1. Check motherboard jumper setting

2. Install CPU and Fan

3. Install System Memory (DIMM)

4. Install Expansion cards

5. Connect hard disk and front panel /back panel cable

6. Connect ATX Power cable

7. Power-On and Load Standard Default

8. Reboot

9. Install Operating System

10. Install Driver and Utility

2-2 Jumper Setting

(1) CMOS RAM Clear (3-pin): JBAT

A battery must be used to retain the motherboard configuration in CMOS RAM.

Note: When should clear CMOS

1. Troubleshooting

2. Forget password

3. After over clocking system boot fail

WARNNING! Please remove or turn off the power supply before CMOS clear.

Following these steps to clear CMOS:

1. Turn off the system and unplug the AC power

2. Remove ATX power cable from ATX power connector

3. Locate JBAT and short pins 2-3 for a few seconds

4. Return JBAT to its normal setting by shorting pins 1-2

5. Connect ATX power cable back to ATX power connector

CMOS RAM Clear Setting

2-3 Closed Clear CMOS

JBATJBAT

1-2 Closed Normal

(2) Keyboard/Mouse Power-on Enabled/Disabled: JP1

Keyboard/Mouse Power On Setting

2-3 Closed KB/MS Power ON Enabled

JP1

1-2 Closed KB/MSPower ON Disable (Default)

(3) USB Power-on Enabled/Disabled: JP2

USB Power On Setting

2-3 Closed: USB Power On Enabled

JP2

1-2 Closed: USB Power On Disable (Default)

2-3 CPU Installation

This motherboard provides a 775-pin surface mount, LGA775 Land Grid Array socket,

referred to as the LGA775 socket supports Intel Pentium Dual Core processor in the

775 Pin package utilizes Flip-Chip Land Grid Array (FC-LGA) package technology.

The CPU that comes with the motherboard should have a cooling FAN attached to

prevent overheating. If this is not the case, then purchase a correct cooling FAN

before you turn on your system.

WARNING! 1.Be sure that there is sufficient air circulation across the processor’s

heatsink and CPU cooling FAN is working correctly, otherwise it may

cause the processor and motherboard overheat and damage, you

may install an auxiliary cooling FAN, if necessary.

. Suggest the power of CPU should below 65w.

To install a CPU, first turn off your system and remove its cover. Locate the LGA775

socket and open it by first pulling the level sideways away from the socket then

upward to a 90-degree angle. Insert the CPU with the correct orientation as shown

below. The notched corner should point toward the end of the level. Because the CPU

has a corner pin for two of the four corners, the CPU will only fit in the orientation as

shown.

CPU LGA775 Socket

Colden Arrow

LGA775

2-4 Memory Installation

The board provides two 240-pin DDRIII DUAL INLINE MEMORY MODULES (DIMM)

socket for DDRIII memory expansion to maximum memory volume of 8GB DDRIII

SDRAM.

Valid Memory Configuration

Bank 240-pin DDRIII DIMM PCS Maximum Capacity

Bank 0, 1 (DIMM1) DDRIII 1066/1333 X1 2GB

Bank 2, 3 (DIMM2) DDRIII 1066/1333 X1 2GB

Total System Memory (Max. 2GB) X2 4GB

Recommend DIMM Module Combination

1. One DIMM Module ----Plug in DIMM1

2. Two DIMM Modules---Plug in DIMM1 and DIMM2 for Dual channel function

For Dual channel Limited!

1. Dual channel function only supports when 2 DIMM Modules plug in either both DIMM1

& DIMM2

2. DIMM1 & DIMM2 must be the same type, same size, and same frequency for dual

channel function.

Install memory modules to your motherboard is not difficult, you can refer to figure

below to see how to install a memory module.

Autres manuels pour G41 Express Chipset

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intel Carte mère

Intel

Intel D915GAG Manuel utilisateur

Intel

Intel CH-486-33A Manuel utilisateur

Intel

Intel EMX-965GME Manuel utilisateur

Intel

Intel BLKD945GCCR Manuel utilisateur

Intel

Intel D945PLRN Manuel utilisateur

Intel

Intel D845GVAD2 - P4 Socket 478 ATX Motherboard Manuel utilisateur

Intel

Intel D850GB Manuel utilisateur

Intel

Intel D845HV Guide de configuration

Intel

Intel D945GPM Manuel utilisateur

Intel

Intel BLKD915PGNL - LGA775 800FSB 4DDR Audio Lan SATA ATX... Guide de configuration

Intel

Intel DG965WH Manuel utilisateur

Intel

Intel SE7501HG2 Manuel utilisateur

Intel

Intel D946GZIS - Desktop Board Motherboard Manuel technique

Intel

Intel DG965MS Manuel utilisateur

Intel

Intel BLKD865PERL Guide de configuration

Intel

Intel D425KT Guide de configuration

Intel

Intel P43 Manuel utilisateur

Intel

Intel DH67CL Manuel utilisateur

Intel

Intel D845GBV Manuel technique

Intel

Intel 945GC Manuel utilisateur

Intel

Intel H61 Express Manuel utilisateur

Intel

Intel D845GRG Mode d’emploi

Intel

Intel DH57DD Manuel utilisateur

Intel

Intel Desktop Board D850EMD2 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur