Inkee Falcon Manuel utilisateur
Falcon User Manual
V1.4
2021.06
Contents
Introduction
Product Contents
01
01
Falcon diagram 02
Product Usage 03
Charging
Installation of Action Camera
03
03
Power Button 05
Mode Function
06
Function Operation
06
Four-directional Joystick Operation
Mode Switch Button
08
09
Trigger Button Operation 10
Manual Lock
Indicator Light Status 11
Disclaimer
FAQ
12
13
11
Shutter Button 05
Connect to device 06
Balance Adjustment 04
Product Parameter 14
Falcon is a hand-held stabilizer specially designed for cameras, which supports most
of Action Cameras on the existing market, Through the three-axis motion
compensation to stabilize the Action Camera to get a stable effect.
Product Contents
Charging Cable x1
Storage Bag(at the bottom
of the package)x1
Tripod x1
Falcon User Manual
Introduction
1
Hexagon Wrench x2
Screw x1
Stabilizer x1
2021 INKEE Falcon All Rights Reserved
Screw to fix camera x1
Quick Start Guide x1
Falcon diagram
Falcon User Manual
2
PF HL
FPV
FL
Camera not included.
Trigger Button
Charging Interface
Tilt Axis
Screw
Status Indicator light
Joystick
Mode Button
ON/OFF Button/ Power Display Button
Roll Axis
Pan Axis
Handle
Shoot Button
Time-lapse Button
REC Button
Camera Mounting
Plate
Front and Rear Balance
Adjusting Lock
2021 INKEE Falcon All Rights Reserved
Left and Right Balance
Adjustment Lock
Falcon User Manual
Product Usage
Make sure to fully charge the stabilizer when use for the first time.
Please charge the stabilizer immediately if the power is too low and the
red-light flashes slowly.
Turn off the power if not in use.
Charging
Use TYPE-C cable to charge. The status indicator is red when charging while the green light
is always on when fully charge.
Take GoPro HERO9 as an example:
① Pull apart the bottom mounting buckle of the action camera and install it on the stabilizer.
② 2)Insert the screw into the hole corresponding to the stabilizer and then tighten the screw.
（*If the installed camera is GoPro hero 8 or GoPro hero 9, it may cause camera lock virtual
position. Please adjust the position of the camera）
Installation of camera
is completed.
Installation of Action Camera
3
PF HL
FPV
FL
Note :
2021 INKEE Falcon All Rights Reserved
Tip: when installing the
camera, keep the camera
as close as possible to the
camera mounting base.
Falcon User Manual
4
2021 INKEE Falcon All Rights Reserved
Balance Adjustment
Determine the center of gravity of the camera. If the camera tilts to the left, it means that
the center of gravity of the camera is to the left. Loosen the left and right balance
adjustment locking screw ①, and move the mounting base and the camera to the right
until it can keep level with the ground when it is still; If the camera is tilted to the right,
move the mounting base and the camera to the left until it is horizontal with the ground
when it is still, and then tighten the screw.
1. Left and Right Balance Adjustment Lock
PF HL
FPV
FL
PF HL
FPV
FL
①
Flip the camera so that the lens is vertically up. Determine the center of gravity of the camera.
When the camera lens is tilted forward, the mounting base and the camera should be moved
backward until it can keep level with the ground when it is still, and then the screw can be
tightened; If the camera lens is tilted backward, the mounting base and the camera should
be moved forward until it can keep level with the ground when it is still, and then the screw
can be tightened.
2.Front and Rear Balance Adjustment
The Action Camera can only be turned on after it is firmly installed.
① Under the condition of power on or off, Long press two seconds the power button to turn
on or turn off the gimbal.
② Under the condition of power on or off, single press the power button to display the
power of stabilizer.
③ In the boot state, double press the power button into standby mode, and then single
press any button to restore the working state of the stabilizer.
④ In the boot state, continuously and quickly press eight times to clear the remote-control
pairing. Too slow will trigger standby.
Power Button
Falcon User Manual
Power Button
Note:
5
Shutter Button
PF HL
FPV
FL
Shooting Button
Time-lapse Button
REC Button
Shooting Button: Single press to shoot
REC Button: Single press to start recording or stop.
Time-lapse Button: Single press the button to start time-lapse shooting or stop.
PF HL
FPV
FL
2021 INKEE Falcon All Rights Reserved
PF HL
FPV
FL
Function Operation
Pan Following Mode
Single press Mode Button
Pan and Tilt Following Mode
Single press the Mode
Button again
Falcon User Manual
Mode Function
6
PF HL
FPV
FL
PF HL
FPV
FL
Following
Rotation
Following
Rotation
Following
Rotation
Single press the Mode
Button again
Full Following Mode
影器Falcon版权所有
① Following Mode
2021 INKEE Falcon All Rights Reserved
Connect to device
① Pull out the Selection Box from top to bottom, Click on “CONNECT”,
② Click on “Connect New Device”, ③ Click on“GOPRO APP”.
* Turn on the gimbal before connect to a device.
* If the above operation fails to connect the device, remove the pairing and make the
following steps, and once again repeat the above steps.
① Pull out the selection box from top to bottom, click on “CONNECT”,
②Click on “Reset Connections ”, ③ Click on “RESET”.
CONNECT NEW DEVICE
GOPRO App
Reom(Voice Remote )
Smart Remote
Return to
GoPro app and
follow Instructions
CANCEL
CAMERA NAME
GP********
PASSWORD
********
Connect New Device
CONNECTED DEVICES
CAMERA INFORMATION
Name & Password
CONNECT
CONNECT
PREFERENCES
CANCEL
RESET CONNECTIONS
Clear your connection list
(reconnect GoPro to the
required device)
RESET
ALL CONNECTIONS RESET
CONNECTED DEVICES
CAMERA INFORMATION
Name & Password
Reset Connections
Wireless Connections
CONNECT
PREFERENCES
Falcon User Manual
7
The red circle indicates that the motor follows the movement of the handle to change
the angle, while the gray circle indicates that the motor locks the angle and does not
follow the movement of the handle.
Double click to enter vertical shooting mode, double click again to ener Flashlight
Mode. Single click to exit to HL mode.
Vertical Shooting Mode Flashlight Mode
② Lock Mode
PF HL FPV FL
③ Vertical shooting Mode and Flashlight Mode
Pan and Tilt Locked Mode
Long press trigger button
Locked direction
2021 INKEE Falcon All Rights Reserved
Pan Following Mode
(default)
Pan and Tilt Following
Mode
Lock Mode
Tilt axis and roll axis keep the same direction, and the lens
rotates with the direction of the handle.
Roll axis keep the same direction, and the lens rotates with
the direction of the handle.
The lens keeps the same direction.
Description
Mode
Reset
Trigger Lock
Vertical Shooting
Return to Pan Following Mode, tilt axis, roll axis and pan axis
return to horizontal state.
Pull the camera to the specified angle of pan axis and tilt axis
for half a second to lock the current angle.
Assist the camera to shoot vertically .
Status Indicator
Light
ON/OFF Button/ Power
Display Button
Mode Button
Four-directional Joystick
Falcon User Manual
Four-directional Joystick Operation
8
Left
Up
Right
PF HL FPV FL
Down
PF HL FPV FL
Push upwards /downwards
Joystick Operation Description
Push left/right
Tilt axis rotates up or down
Pan axis rotates left or right.
2021 INKEE Falcon All Rights Reserved
Full Following Mode The lens rotates in the direction of the handle .
Flash Light Mode Make the camera rotate 360.
Autres manuels pour Falcon
1
Table des matières
Autres manuels Inkee Accessoires pour appareils photo
