Inkee Falcon Plus Manuel utilisateur
Falcon Plus User Manual
V1.1
2021.12
Falcon Plus is a hand-held stabilizer specially designed for cameras, which supports
most of Action Cameras on the existing market, Through the three-axis motion
compensation to stabilize the Action Camera to get a stable effect.
Product Contents
Charging Cable*1
Storage Bag(at the bottom
of the package)*1
Tripod *1
Falcon User Manual
Introduction
1
Hexagon Wrench *2Screw*1
Stabilizer *1
2021 INKEE Falcon All Rights Reserved
Screw to fix camera*1
Quick Start Guide *1
Falcon diagram
Falcon User Manual
2
Camera not included.
Trigger Button
Charging Interface
Tilt Axis
Screw
Status Indicator light
Joystick
Mode Button
ON/OFF Button/ Power Display Button
Roll Axis
Pan Axis
Handle
Shoot Button
Time-lapse Button
REC Button
Camera Mounting
Plate
Front and Rear Balance
Adjusting Lock
2021 INKEE Falcon All Rights Reserved
Left and Right Balance
Adjustment Lock
Falcon Plus User Manual
Product Usage
Make sure to fully charge the stabilizer when use for the first time.
Please charge the stabilizer immediately if the power is too low and the
red-light flashes slowly.
Turn off the power if not in use.
Charging
Use Type-C cable to charge. Blue light flashes during charging. All the four lights are always
on when fully charged.
Take GoPro HERO 10 + MEDIA MOD as an example:
① Pull apart the bottom mounting buckle of the action camera and install it on the stabilizer.
② Insert the screw into the hole corresponding to the stabilizer and then tighten the screw.
（*If the installed camera is GoPro hero 8 or GoPro hero 9, it may cause camera lock virtual
position. Please adjust the position of the camera）
Installation of camera
is completed.
Installation of Action Camera
3
PF HL
FPV
FL
Note :
2021 INKEE Falcon All Rights Reserved
Tip: when installing the
camera, keep the camera
as close as possible to the
camera mounting base.
Falcon Plus User Manual
4
2021 INKEE Falcon All Rights Reserved
Balance Adjustment
Determine the center of gravity of the camera. If the camera tilts to the left, it means that
the center of gravity of the camera is to the left. Loosen the left and right balance
adjustment locking screw ①, and move the mounting base and the camera to the right
until it can keep level with the ground when it is still; If the camera is tilted to the right,
move the mounting base and the camera to the left until it is horizontal with the ground
when it is still, and then tighten the screw.
1. Left and Right Balance Adjustment Lock
Flip the camera so that the lens is vertically up. Determine the center of gravity of the camera.
When the camera lens is tilted forward, the mounting base and the camera should be moved
backward until it can keep level with the ground when it is still, and then the screw can be
tightened; If the camera lens is tilted backward, the mounting base and the camera should
be moved forward until it can keep level with the ground when it is still, and then the screw
can be tightened.
2. Front and Rear Balance Adjustment
①
The Action Camera can only be turned on after it is firmly installed.
① Under the condition of power on or off, Long press two seconds the power button to turn
on or turn off the gimbal.
② Under the condition of power on or off, single press the power button to display the
power of stabilizer.
③ In the boot state, double press the power button into standby mode, and then single
press any button to restore the working state of the stabilizer.
④ In the boot state, continuously and quickly press eight times to clear the remote-control
pairing. Too slow will trigger standby.
Power Button
Falcon Plus User Manual
Power Button
Note:
5
Shutter Button
PF HL
FPV
FL
Shooting Button
Time-lapse Button
REC Button
Shooting Button: Single press to shoot
REC Button: Single press to start recording or stop.
Time-lapse Button: Single press the button to start time-lapse shooting or stop.
PF HL
FPV
FL
2021 INKEE Falcon All Rights Reserved
Falcon Plus User Manual
6
Indicator
Light Status Description
Indicator Light Status
In shutdown and standby mode, the current power is 0-25%, 25-50%,
50-75%, 75-100% from the left.
Blue LED Light Represent the mode state after Turning on, in proper sequence from left to
right are: PF mode, HL mode, FPV mode, Flashlight mode(FL), under Lock
mode(GL) the LED all bright, Vertical Shooting Mode (FL flashes).
Green LED Light
Display the Bluetooth connection status. It is always on when the Bluetooth
is connected while it is always off when no connection. After pairing is
cleared, the light will flash slowly during the Bluetooth scanning, if there is
connected then always on if not then off light.
Red LED Light
Display the current upgrade status. The red-light flashes rapidly during
upgrade, and it will turn off after three seconds when upgrade completed.
When the power is lower then 10% the red-light flashes slowly, Red light
flashing indicates upgrade failure
影器Falcon版权所有
2021 INKEE Falcon All Rights Reserved
Mode Switch Button
1、Illustration
① Single click to switch PF-HL-FPV mode.
② Double click to enter vertical shooting mode, double click again to ener Flashlight Mode.
Single click to exit to HL mode.
③ Long press the Trigger Button to enter GL Mode(Lock Mode), release to back to previous
mode(GL Mode works only under PF or HL Mode).
2、The current mode of the stabilizer can be identified by the status of the indicator light.
PF Pan Following HL Pan/Tilt Following FPV Three axis all Following
PF HL FPV FL
PF HL FPV FL PF HL FPV FL
Falcon Plus User Manual
7
2021 INKEE Falcon All Rights Reserved
Vertical Mode
(the indicator light flashes)
Lock ModeFlashlight Mode
PF HL FPV FL PF HL FPV FL
HL FPV FL
PF
Function Operation
Pan Following Mode
Single press Mode Button
Pan and Tilt Following Mode
Single press the Mode
Button again
Mode Function
Following
Rotation
Following
Rotation
Following
Rotation
Single press the Mode
Button again
Full Following Mode
① Following Mode
Falcon Plus User Manual
8
2021 INKEE Falcon All Rights Reserved
The red circle indicates that the motor follows the movement of the handle to change
the angle, while the gray circle indicates that the motor locks the angle and does not
follow the movement of the handle.
② Lock Mode
Pan and Tilt Locked Mode
Long press trigger button
Locked direction
Double click to enter vertical shooting mode, double click again to ener Flashlight
Mode. Single click to exit to HL mode.
Vertical Shooting Mode Flashlight Mode
③ Vertical shooting Mode and Flashlight Mode
Falcon Plus User Manual
9
Status Indicator
Light
ON/OFF Button/ Power
Display Button
Mode Button
Four-directional Joystick
Four-directional Joystick Operation
Left
Up
Right
PF HL FPV FL
Down
PF HL FPV FL
Push upwards /downwards
Joystick Operation Description
Push left/right
Tilt axis rotates up or down
Pan axis rotates left or right.
2021 INKEE Falcon All Rights Reserved
Pan Follow (PF)
Horizontal Lock (HL)
(Default Mode)
First Person View (FPV)
Tilt axis and roll axis keep the same direction, and the lens
rotates with the direction of the handle.
The lens follows the projection direction of the handle to
simulate the first-person visual effect.
Roll axis remains horizontal, and the lens rotates in the
direction of the handle.
Mode
Flashlight Mode (FL)
Global Lock (GL)
When the handle is parallel to the ground, vertical shooting
with 360 rotation can be carried out.
Press and hold the trigger button to enter into full lock
under PF/HL mode.
Vertical Shooting Assist the camera to shoot vertically.
Description
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Inkee Accessoires pour appareils photo
