Ingics iGS03W Manuel utilisateur
INGICS TECHNOLOGY
iGS03W/M is a gateway to bridge the local BLE( Bluetooth® Low Energy) tags,
sensors, or beacons to remote server/cloud by WiFi, or LTE-M. Through an easy web
UI interface, user can configure the Internet access to upload reports to cloud server
by TCP, HTTP(S), or MQTT(S). This guide is to help the user to figure out how to
operate and configure the iGS03.
Contents:
Overview
Block Diagram
SIM
WiFi
BLE
GNSS
Example case 1: The device is in fixed position:
Example case 2: The device is moving:
Payload Format
BLE
GPS
Button
Reset to Default
WPS
LEDs
Configuration
Web User Interface
System
Wi-Fi
AP Mode
Station Mode
Network
WiFi Address
DHCP Server (WiFi AP)
Applications
TCP Server
TCP Client
HTTP Client
HTTPS
MQTT Client
Guide
Ver.01a
Beacon Gateway
iGS03W/M User Manual
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
1
INGICS TECHNOLOGY
MQTTS
Common Settings
Content Type
Keep Alive
Append Timestamp
Request Interval
Cache full handling
Throttle Control
Cloud IoT Helper
Advanced
BLE Configuration
BLE-5 PHY Mode
Active Scan Mode
BLE Filter
RSSI Threshold
Payload Whitelist
BLE MAC Whitelist
Security
Device Key/Certification/Server CA Upload
LTE
LET Settings
APN
Auth
Username/Password
GNSS Settings
NTP Setting
Certification
Bluetooth SIG Qualification
Japan MIC Reaulatory
FCC Regulatory
FCC Statements
CE Regulatory
Revision History
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
2
INGICS TECHNOLOGY
Overview
The iGS03 BLE gateway scans beacons(like iBeacon or Eddystone), proprietary tags, or BLE
sensors then sends the payload to TCP, HTTP or MQTT server. Users can configure the transmit period
and server endpoint through a simple web UI. There are two models, iGS03W and iGS03M, representing
different uploading interfaces, WiFi and LTE-M.
Block Diagram
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
3
INGICS TECHNOLOGY
SIM
To use iGS03M (LTE-M Model), you have to put a Cat-M1 micro
SIM card into the socket of iGS03M. Please open the bottom cover to
insert the SIM card. The steps to open the bottom cover are as below,
WiFi
The 2.4G WiFi AP connection is used to configure the unit through web UI. iGS03 works as an
WiFi Access Point(AP) supporting DHCP. Users must connect to this AP to configure the unit.
BLE
The BLE subsystem operates in listening mode. It collects the messages advertised by BLE
devices. These messages are then sent to the cloud server configured by the user.
iGS03 supports two BLE modes
1. LE 1M PHY: including BLE4.2(Legacy)/BLE5, 1M in 100% duty cycle
2. LE Coded PHY: BLE5, 125K( long range) in 100% duty cycle
Step 1. Remove external BLE antenna
Step 2. Remove the screw from bottom cover
Step 3. Use finger to press and hold the arrow
part
Step 4. Pull out the bottom cover
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
4
INGICS TECHNOLOGY
The default PHYMODE is 1, LE 1M PHY mode.
Users can use webUI or telnet command to configure the mode.
GNSS
The GNSS function is turned “off” by default. Users can use webUI to enable or disable GNSS.
For detail settings, use below telnet commands to manage the GNSS behavior:
GNSS ENABLE Enable/Disable GNSS, default off
GNSS FIXCOUNT Number of attempts for positioning, 0 indicates continuous positioning.
default 0
GNSS FIXRATE The interval time between the first and second time positioning, default 1 (1
second)
GNSS RPTRATE The interval time for sending GPSR report, default 600 (10 minutes)
GNSS INFO To get latest GPS status
Example case 1: The device is in fixed position:
e.g.
GNSS ENABLE 1
GNSS FIXCOUNT 5
GNSS FIXRATE 60
GNSS RPTRATE 60
Then GNSS will be enabled and get positioned for 5 times with a 60 seconds interval.
GNSS will be off automatically after getting position for 5 times.
Example case 2: The device is moving:
e.g.
GNSS ENABLE 1
GNSS FIXCOUNT 0
GNSS FIXRATE 1
GNSS RPTRATE 60
Then GNSS will be enabled and continuously get position with 1 second interval, and it will send
a GPSR report every 60 sec.
You can also use the "GNSS INFO" command to get the latest coordinates.
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
5
INGICS TECHNOLOGY
Payload Format
There are several kinds of payload format that iGS03 will send to the server.
BLE
General format:
$<report type>,<tag id>,<gateway id>,<rssi>,<raw packet content>,*<unix epoch timestamp>\r\n
Report Type:
$GPRP BLE4.2 General Purpose Report
$RSPR BLE4.2 Scan Response Report
$LRAD BLE5 Long Range ADV
$LRSR BLE5 Long Range Scan Response
$1MAD BLE5 1M ADV
$1MSR BLE5 1M Scan Response
Examples:
$GPRP,CCB97E7361A4,CB412F0C8EDC,-49,1309696773206D65736820233220285445535429020106,1574921085
$GPRP,E5A706E3923A,CB412F0C8EDC,-87,0201041AFF590002150112233445566778899AABBCCDDEEFF0000100C3BB,157
4921085
$LRAD,51A88AD374B7,CC4B73906F96,-87,02010212FF0D0083BC280100AAAAFFFF000010030000,1574921085
$GPRP,0C61CFC1452E,E7DAE08E6FC3,-44,0201061AFF4C000215B9A5D27D56CC4E3AAB511F2153BCB9670001452ED6
(iBeacon, UUID: B9A5D27D56CC4E3AAB511F2153BCB967, Major: 0001, Minor: 452E)
GNSS
General format:
$GPSR,<tag_mac>,<reader_mac>,<rssi>,yymmdd,hhmmss.ss,latitude,longitude,speed,hdop(,timestamp)
●"$GPSR,<tag_mac>,<reader_mac>,<rssi>" fields are for compatibility with other reports. The
tag_mac is always the same as reader_mac and the rssi is always -127.
●yymmdd,hhmmss.ss is the UTC time when the position is acquired.
<report type>
Different report type to distinguish the source of the report.
<tag id>
MAC address or ID of tag/beacon
<gateway id>
MAC address of gateway
<rssi>
RSSI of tag/beacon
<raw packet content>
Raw packet received by the gateway
<unix epoch timestamp>
Optional timestamp configured in applications page
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
6
INGICS TECHNOLOGY
●speed: The unit is knots.
●hdop: Horizontal dilution of position
Example:
$GPSR,CC4B73906F96,CC4B73906F96,-127,191127,233821.00,24.993631,121.423264,0.0,2.4,1574897900
Button
One button is located on the back panel. It is used for WPS function or Reset to default settings.
Reset to Default
Pressing the reset button on your device for over 3 secs to retrieve the default setting. While the
network status LED turns into red light, release the button, and the iGS03M will reboot with its default
settings.
WPS
Users can use the WPS button to join iGS03M to the WiFi Access Point. First press the WPS
button on your Access Point, when it is ready, then press the WPS button for over 1 sec on the iGS03M
device to join the Access Point.
Function
Trigger Condition
WPS
short press for over 1sec and release
Reset to default settings
long press for over 3 sec
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
7
INGICS TECHNOLOGY
LEDs
There are two LEDs indicating the current status. The left one is BLE status LED and the right one
is Network status. Below are their behaviors.
Configuration
To configure the unit, you have to connect it through the WiFi interface. When it is powered on,
you could scan its native AP and connect it with the WiFi of your NB/PC/Mac/Tablet/Smartphone. It’s
On
Flash
BLE
Status
LED
find tag/beacon in range
BLE transmission
happening
Network
Status
LED
WiFi/LTE-M connection
success
(This only implies the network
is connected. It doesn’t mean
the server is connected)
Green: WiFi/LTE-M
network transmission
happening
Orange:
If IGS03M does not insert
SIM card and being used
as WiFi device
Network Status LED behavior
Description
Status
ORANGE LED on (500ms)
Boot start
Booting
RED LED blink (100ms on/off)
Joining AP (If WiFi in STA mode)
Booting
RED LED blink (500ms on/off)
LTE connecting carrier
Booting
GREEN/ORANGE LEDs blink interleaved
(100ms)
WPS enrollee
WPS
GREEN LED on
Network ready
Ready/Idle
ORANGE LED on
Network ready (If SIM card is not inserted)
Ready/Idle
GREEN LED blink (200ms on/off)
Network is transfering data
(If SIM card is not used on iGS03M, shows
ORANGE LED blink instead)
Busy
RED LED ON (1sec)
Connect failure
Error
RED LED blink (5sec on/off)
Misconfiguration
Error
RED LED ON (5sec)
LTE init failure
Error
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
8
INGICS TECHNOLOGY
SSID is just like the above figure with part of the mac address. The default key to connect with it is
“12345678”. You can change it later when you get into the web UI.
After connection, enter IP address 192.168.10.1 in your browser. The default account/password
are both “admin”. The following sections describe details of the web UI.
Web User Interface
You can review current configuration or modify it on the web UI. There are various function
groups listed on the top of UI.
Any change in the page needs to be saved first before switching to another page, otherwise the
modification will be lost. And after all changes made, click reboot to make the changes effective.
System
Display firmware and device information, including MAC address and IP address in station mode
are shown here.
Wi-Fi
Users can configure iGS03M’s WiFi device as an WiFi AP or join to the other AP. The related
settings can be managed on this page.
AP Mode
SSID: The default name is IGS03 plus
the last digits of the mac address.
Security: Open, WPA-PSK, WPA2-PSK
and WPA-PSK/WPA2-PSK are
supported. WPA2-PSK is
recommended.
Password: 8-63 characters can be
input
Channel: 1~11(ch12 and ch13 could be supported by request)
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
9
INGICS TECHNOLOGY
Station Mode
This mode is used for transferring
data by *WiFi.
Scan: Click it to scan available APs.
The scan result list will be displayed
on the popup window, and the user
can choose the correct AP from the
list.
SSID: No manual input required. It is automatically filled once a user chooses an AP from
the scan result list.
Security: Basically it is automatically detected and selected after choosing an AP from the
scan list. But in case the AP setting is in WEP open or WEP shared, the user has to
confirm it by himself/herself.
Password: Type the one assigned in your AP.
*Note: In data transfer, by default, WiFi has higher priority than LTE. So for iGS03M if both
interfaces are configured correctly and connected, the data will be transferred by WiFi.
Users can change the priority through the Telnet command.
Network
WiFi Address
This setting is for configuring in WiFi
Station mode. Normally the “DHCP
Client” is used to join a WiFi AP w/
DHCP. If one wants to manually assign
an IP address for iGS03, choose “Static
IP” to to assign the IP Address,
Netmask, Gateway, and/or DNS
servers.
DHCP Server (WiFi AP)
The default IP address of iGS03 in WiFi AP mode is 192.168.10.1 and the netmask is
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
10
Autres manuels pour iGS03W
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ingics Porte
Ingics
Ingics iGS03W Manuel utilisateur
Ingics
Ingics iGS02E Manuel utilisateur
Ingics
Ingics IGS01 Manuel utilisateur
Ingics
Ingics iGS01S Manuel utilisateur
Ingics
Ingics iGS03W Manuel utilisateur
Ingics
Ingics iGS01S Manuel utilisateur
Ingics
Ingics iGS03W Manuel utilisateur
Ingics
Ingics IGS01 Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
