InfiRay PT2 Manuel utilisateur

Dual-spectrum PT2 Network

Thermal Camera

Quick Start Guide

V1.0.0

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 1 -

Preface

The following is about the correct use of the camera. In order to prevent danger

and loss of property, please read this manual carefully before using the camera

and strictly follow it during use. Please keep the manual properly after reading.

Overviews

This manual is suitable for dual-spectrum PT2 network thermal cameras.

This manual describes the installation steps, installation precautions and basic

operations of dual-spectrum PT2 network thermal cameras.

Symbol Description

The description of the symbols that appear in the document is as follows.

Instruction

The instructions are an emphasis and supplement to the main

text.

Caution

Cautions indicates potential risks. If ignored, it may lead to

product damage, data loss, product performance degradation,

or unpredictable results.

Warning

Warnings indicates that low or medium potential risk is

existing. The ignorance of the warnings may lead to injury,

equipment damage, or business interruption.

Danger

Dangerous text indicates that there is a high potential risk. If

it is not avoided, a major risk of personal injury or even death

may be caused.

Important Safety Notice

Warnings

The local electrical safety standards should be rigorously followed in the process

of installation and usage.

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 2 -

⚫Please use power adapter which is produced by regular companies. Please

check whether the power is normal or not before starting the camera. (Power

supply requirements should comply with that on the product labels.)

⚫In order to make emergency power off when necessary, please install

power-off equipment which is easy to use when installing the wires.

⚫Please protect power lines from being treaded or pressed, especially the

connecting points which are led from the plug, power socket or other unit.

⚫Please make sure the camera is fixed firmly in case of being installed on walls

or ceilings.

⚫If the camera does not work normally, please contact the purchased shops or

factories. Do not disassemble or revise the camera in any way (The

manufacturing company is not responsible for problems that are caused by

unauthorized modification or maintenance.)

Cautions

⚫Please do not put the camera in damp, dusty, extremely hot or cold places,

or places with corrosive gas or unstable light.

⚫Please transport, use and store the camera within the allowable humidity and

temperature range.

⚫Avoid making the lens aiming at strong light (e.g. sun or laser), otherwise the

imaging sensor would be damaged.

⚫Please do not block the vents near the camera in case of heat accumulated.

⚫Please use the factory packaging or materials of the same quality when

shipping the device.

⚫Please do not press, vibrate violently or soak the camera during transportation,

storage or installation.

⚫It is advised to use the camera with lighting protector.

⚫Soft dry cloth can be used to clean the camera. For the dirt difficult to clean,

please use soft cloth with little neutral detergent and then wipe dry. Do not

use volatile detergent like alcohol, benzene or diluent, or strong and abrasive

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 3 -

detergent, otherwise the camera coating would be damaged and also the

camera performance could be degraded.

⚫The lens cover is optical device, so please do not touch directly or wipe the

cover. Soft brush or hairdryer can be used to blow the dust away. For the

grease or fingerprint, soft cloth can be used to wipe it away. Cotton cloth or

lens cleaning paper with cleaning solution can be used to wipe repeatedly

until it’s clean.

⚫Please revise the password promptly after logging in.

Instruction

⚫Please use the accessories or parts specified by the manufacturer and have

them installed and repaired by professional service personnel.

⚫Quality requirements for installation and maintenance personnel:

Personnel should have the qualification certificate or experience to engage in

the installation and maintenance of video surveillance systems, and have the

qualification to engage in related jobs (such as high-altitude operations, etc.),

in addition to the following knowledge and operating skills.

Equipped with basic knowledge and installation skills of video surveillance

system and its components.

Equipped with basic knowledge and operating skills of low-voltage wiring

and low-voltage electronic circuit wiring.

Equipped with basic network security knowledge and skills, and have good

acknowledge of this manual.

⚫Requirements for lifting equipment:

Safe lifting equipment suitable for site and method of camera installation.

The lifting equipment is able to reach enough height of installation position.

The lifting equipment has good safety performance.

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide 
 - 4 -
Table of Contents 
Camera Introduction ........................................................................... - 5 - 
1 Camera Description.......................................................................... - 5 - 
2 Camera Features............................................................................... - 5 - 
3 Camera Appearance ......................................................................... - 6 - 
4 Cable Introductions.......................................................................... - 6 - 
5 Alarm Interface Connection............................................................. - 8 - 
Camera Installation.............................................................................. - 8 - 
1 Instructions before Installation......................................................... - 8 - 
2 Cable Planning and Wiring.............................................................. - 8 - 
3 Mounting Bracket............................................................................. - 9 - 
4 TF Card Installation ....................................................................... - 10 - 
5 PT Installation ................................................................................ - 10 - 
6 Install Network Port Protective Cover........................................... - 11 - 
Operation Guide................................................................................. - 12 - 
1 Preparations.................................................................................... - 12 - 
2 Login System.................................................................................. - 13 - 
3 Main Interface Description............................................................. - 14 - 
Appendix A Camera Maintenance......................................................... - 15 - 
Appendix B Operating Distance............................................................. - 16 - 
Appendix C Emissivity of Common Materials...................................... - 17 - 
 
 
 

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 5 -

1. Camera Introduction

1.1 Camera Description

The dual-spectrum PT2 network camera is a thermal imaging network

camera that integrates remote monitoring in all-weather conditions, video

services and high-definition camera functions. In addition to the basic

visible light imaging, the camera also comes with a thermal imaging

channel, which can more comprehensively collect the characteristic

information of the measured scene while realizing dual-light shooting. It

can be widely used in indoor and outdoor scene monitoring, perimeter

prevention, fire warning integration and other fields of smart security.

1.2 Camera Features

⚫With the latest InfiRay® 12μm IR thermal imaging detector, the thermal

camera can make farther and clearer images.

⚫With a maximum thermal imaging resolution of 1.3 megapixels and a

20x 4 megapixel visible light camera，high-definition dual-spectrum

imaging can be achieved.

⚫Support 9.1/13/19/25/35mm fixed-focus and 13/25mm fixed electronic

zoom infrared lens, which can meet various inspection needs.

⚫Support network high-definition transmission, which can transmit visible

light videos and infrared videos at the same time.

⚫Combining multiple network monitoring methods, the camera also

supports ONVIF protocol.

⚫With high-speed, high-precision pan-tilt, the network camera supports 5

scanning methods and 17 scanning tracks with speed memory;

⚫Support smart smoke & fire detection.

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 6 -

⚫Support intelligent infrared video analysis, including intelligent analysis

functions such as regional intrusion, trip wire, etc.

⚫With IP66 encapsulation level

⚫Single IP

⚫With ±2℃ high temperature measurement accuracy

1.3 Camera Appearance

Figure 1.1 Appearance of Dual-spectrum PT2 Network Thermal Camera

1.4 Cable Introductions

The cable includes interfaces for power, alarm, audio, RS-485, and network,

etc. Please see the following figure for interface introductions.

⚫P1nework interface（LAN）：Output network signal and connect to

standard Ethernet cable.

⚫P2 power interface（DC24V）： Support DC24V power supply.

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 7 -

⚫P3 audio output（AUDIO OUT）：Output audio signal to speakers and

other equipment for sound output.

⚫P4 audio input（AUDIO IN）：Input audio signal and connect

microphone for receiving linear analog audio signal to collect sounds.

⚫P5 alarm input（ALARM IN）： Receive the switch signal from the

external alarm source.

⚫P6 alarm output（ALARM OUT）： Output alarm switch signal to alarm

equipment.

⚫P7 RS-485（485）：RS485 for PT control.

⚫P8 power interface（DC12V）：support DC12V power supply.

⚫P9 power interface（DC24V）：support DC24V power supply.

Figure 1.2 Cable Introductions

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 8 -

1.5 Alarm Interface Connection

The camera can be connected with alarm signal (0～DC5V) input and switch

output (no voltage). An external power supply is required when connecting the

alarm apparatus. The specific wiring method is shown in the figure below.

Figure 1.3 Alarm Output Wiring Method

2. Camera Installation

2.1 Instructions before Installation

⚫Before installation, please make sure that the camera in the package is in

good condition and all parts are complete.

⚫Before installing the PT, please prepare in advance the tools and cables

that may be required for installation.

2.2 Cable Planning and Wiring

It is necessary to survey and plan the lines in advance since the

environment and location of the PT installation is different, and then to

arrange the lines precisely so as to provide safe and stable power and

wiring for the PT. In the process of cable planning and wiring, you need to

follow the below suggestions:

Dual-spectrum PT2 Network Thermal Camera Quick Start Guide

- 9 -

⚫Before performing cable wiring operations, familiarize yourself with the

installation environment, including wiring distance, wiring environment,

and whether it is far away from magnetic field interference and other

factors.

⚫Please select a wire with a rated voltage greater than the actual line

voltage for the PT to ensure the normal operation of the PT under the

condition of unstable voltage.

⚫To avoid disconnection, the connection of the PT should be done

independently with one wire; if the conditions are limited, it is also

necessary to protect the connection and take reinforcement measures to

prevent the equipment from malfunctioning due to circuit aging.

⚫Strengthen the protection for power lines and signal transmission lines.

Pay special attention to the reinforcement and protection of the line

during the wiring process, so as to avoid abnormal monitoring due to

wiring damage.

⚫During the wire deployment process, do not make the wires too long or

too short.

The cable wiring of the PT should be operated by personnel with

professional skills. When the PT fails to work normally, you can investigate

the cause in the above-mentioned aspects.

2.3 Mounting Bracket

The PT is different from other cameras. The overall quality is heavy, which

has high requirements for the load-bearing and stability of the support. It is

generally recommended to install it directly on the base to avoid potential

safety hazards.

If mounting a bracket is necessary, you can design the corresponding

bracket according to the base map of the PT. The bracket design must

consider factors such as load-bearing and anti-shake to ensure the firmness

of the bracket and the smoothness of the image.

Table des matières

Autres manuels InfiRay Caméra thermique

InfiRay

InfiRay M200 Series Manuel utilisateur

InfiRay

InfiRay Xmini Series Manuel utilisateur

InfiRay

InfiRay Tube Series Manuel utilisateur

InfiRay

InfiRay T Series Manuel utilisateur

InfiRay

InfiRay Geni Series Manuel utilisateur

InfiRay

InfiRay PT Series Manuel utilisateur

InfiRay

InfiRay ITSII 300 Manuel d'instructions

InfiRay

InfiRay Clip CH50 V2 Manuel utilisateur

InfiRay

InfiRay P Series Manuel utilisateur

InfiRay

InfiRay AT Series Manuel utilisateur

InfiRay

InfiRay AT31F Manuel utilisateur

InfiRay

InfiRay Tianxuan M20 Series Manuel utilisateur

InfiRay

InfiRay AT300 Series Manuel utilisateur

InfiRay

InfiRay P2 Pro Manuel utilisateur

InfiRay

InfiRay CLIP NV Series Manuel utilisateur

InfiRay

InfiRay Cabin Series Manuel utilisateur

InfiRay

InfiRay S Series Manuel utilisateur

InfiRay

InfiRay Tianshu C Series Manuel utilisateur

InfiRay

InfiRay Tube SE Series Manuel utilisateur

InfiRay

InfiRay XTHERM II Manuel utilisateur

InfiRay

InfiRay Xmini Manuel utilisateur

InfiRay

InfiRay ZOOM V2 Manuel utilisateur

InfiRay

InfiRay AT20 Manuel utilisateur

InfiRay

InfiRay AT Series Manuel utilisateur

Manuels Caméra thermique populaires d'autres marques

Hikmicro

Hikmicro B20 Manuel utilisateur

FLIR

FLIR E-EST Series Manuel utilisateur

FLIR

FLIR M-Series Manuel utilisateur

BST

BST BT-72 Manuel utilisateur

FLIR

FLIR G300 pt Series Manuel utilisateur

CBC

CBC EN7-S02T Manuel utilisateur

Satir

Satir YRH600 Manuel utilisateur

TESTO

TESTO 882 Manuel utilisateur

TECPEL

TECPEL TIG-320 Manuel utilisateur

SKF

SKF TKTI 21 Manuel utilisateur

TESTO

TESTO 885 Manuel utilisateur

FLIR

FLIR X6530sc Series Manuel utilisateur

Videotec

Videotec MAXIMUS MVXT Manuel utilisateur

Guide Sensmart

Guide Sensmart D384M Manuel utilisateur

NBN

NBN FLIR A6 Series Manuel utilisateur

WORKSWELL

WORKSWELL SAFETIS Manuel utilisateur

Major tech

Major tech MTi11 Manuel utilisateur

COHU

COHU 5935-1000/T100 Manuel utilisateur