INetVu 5000 Manuel utilisateur

C-Com Satellite Systems Inc Page 1 of 79

iNetVu™ 5000 Controller User Manual

The iNetVu™ brand and logo are registered trademarks of C-COM Satellite Systems, Inc.

1-877-iNetVu6

www.c-comsat.com

Revision 1.0.6

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

C-Com Satellite Systems Inc Page 2 of 79

Reproduction, adaptation, or translation without prior written permission is prohibited, except as

followed under the copyright laws.

Both the iNetVu™ and C-COM names and logos are registered trademarks of C-COM Satellite

Systems Inc.

Intel®Pentium is a registered trademark of Intel Corporation. Microsoft, Windows, Windows NT

and MapPoint are registered trademarks of Microsoft Corporation.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies and are the sole property of their respective manufacturers.

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

C-Com Satellite Systems Inc Page 3 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

FCC and INDUSTRY CANADA INFORMATION TO THE USER:

The FCC and Industry Canada have imposed the following conditions when operating,

installing and deploying iNetVu™ Mobile Earth Stations and is mandatory for all

installations made within the Continental United States and Canada as well as Hawaii,

Alaska, Puerto Rico, the U.S. Virgin Islands and other U.S. Territories. The FCC

requires that a certified installer perform the installation. It is also strongly recommended

that a qualified professional RV dealer/installer mount the system on your vehicle.

These conditions are also required by C-COM for all other installed locations.

All iNetVu™ Mobile earth station installers must be C-COM Certified, and must have

specifically acknowledged the requirements for iNetVu™ Mobile installations, which are

as follows:

1. “Installation” is the physical mounting and wiring of the Satellite provider’s earth

station on a vehicle or other stationary site in order to prepare for correct

operation. Only Certified C-COM iNetVu installers may perform the installation

and removal of an iNetVu™ Mobile system.

2. “Deployment” means the raising, pointing and orienting of the earth station to the

communicating satellite, every time it is raised from a stowed position for use.

The deployment of an iNetVu™ Mobile system must only be done by a trained

installer or by a consumer using the deployment software.

3. Installers shall install the iNetVu™ systems only in locations that are not readily

accessible to children and in a manner that prevents human exposure to

potential radiation hazards.

4. For large vehicles with roof mounts, the height of the bottom lip of the earth

station when fully deployed must be at least six feet above the ground at all

times, or six feet above a surrounding surface which a person may easily access.

5. If a roof access ladder or any other means of access to the roof is installed on

the vehicle, then the ladder or access must be blocked by a suitable rope or

other barrier while the earth station is deployed or in operation. The installer

must provide this rope or barrier directly to the end user at the time of installation

and advise the user to use it at all times when the earth station is deployed or in

operation. Warning signs shall also be provided by the installer to the end user

to be posted on the rope or other barrier warning all persons not to attempt to

access the roof of the vehicle while the earth station is deployed or in operation.

6. Warning signs shall be posted at prominent locations on the earth station

informing all persons of the danger of harmful radiation from the earth station

while it is deployed or while in operation.

7. The iNetVu™ Mobile system may only be operated when the vehicle is

stationary.

8. The installer must inform the end user that the vehicle must be stabilized during

the transmission, to prevent movement of the vehicle for any reason, including

movement of persons on or off the vehicle, or high winds. The installer shall

advise the end user how to appropriately stabilize their vehicle.

9. Installers shall be liable for all damages if they fail to comply with the above

mandatory conditions. This includes, but is not limited to damages caused by

improper installation or due to the failure to provide required information to the

end user.

C-Com Satellite Systems Inc Page 4 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

10. Installers and end users will be deemed directly liable for any damages resulting

from either of their failure to comply with the above rules. These rules are meant

to ensure that extraordinary precautions and measures are used to prevent

satellite interference or exposure to harmful radiation. C-COM reserves the

rights to immediately suspend without liability or previous notice the

operation of the earth station upon detection of a deviation from its installation or

operational requirements until the deviation is corrected. In addition, C-COM

reserves the right to suspend or cancel the Installer Certificate of any installer

that has not fully complied with these installation requirements.

11. Further, the installer and end user may be directly liable for any damages

resulting from any change undertaken by either of them. Including but not limited

to, any modification of any part of the hardware, software, specific operational

frequencies, the authorized satellite, or the size or other characteristics of the

earth station supplied to them by C-COM or C-COM’s authorized

representatives.

Note 1:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this instruction manual, may

cause harmful interference with radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio / TV technician for help.

Note 2:

This Class B digital apparatus complies with Canadian ICES-003.

C-Com Satellite Systems Inc Page 5 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

Table of Contents

Introduction ....................................................................................................................... 8

Specifications .................................................................................................................... 9

Physical........................................................................................................................... 10

System Power ................................................................................................................. 11

Typical Connection Configuration ................................................................................... 12

Installation....................................................................................................................... 15

1.1. Setup ................................................................................................................ 15

LED Definition .................................................................................................................16

Automatic Controls Button Operation.............................................................................. 17

DVB Receiver Operation................................................................................................. 18

1.2. Stand-alone Receiver ....................................................................................... 19

1.3. Existing Modem Integration .............................................................................. 19

1.4. Setting Target Satellite ..................................................................................... 19

1.5. Disabling DVB Receiver ................................................................................... 20

1.6. How to Set Network Configurations on your PC............................................... 22

Operation ........................................................................................................................ 23

1.7. Operating Environment..................................................................................... 23

1.8. Transport Conditions ........................................................................................ 23

1.9. Starting iNetVu™ Mobile .................................................................................. 24

1.10. iNetVu™ 5000C Controller Basic Operations ............................................... 24

1.10.1. How to Find Satellite .............................................................................. 24

1.10.2. How to Stow the Antenna ......................................................................24

1.10.3. How to Stop ........................................................................................... 25

1.10.4. How to Reset .........................................................................................25

1.11. Software Basic Operations............................................................................ 25

1.11.1. Finding Satellite ..................................................................................... 25

1.11.2. Stowing the Antenna.............................................................................. 26

1.12. Shortcut Keys................................................................................................ 26

1.13. Transmitter Enabled Movement .................................................................... 26

iNetVu™ Mobile Software ............................................................................................... 28

1.14. Introduction ................................................................................................... 28

1.15. Initial System Configuration .......................................................................... 28

1.16. Operation Modes........................................................................................... 29

1.17. Navigating Menus ......................................................................................... 30

1.18. Switching Operation Modes .......................................................................... 30

1.19. iNetVuTM Menus (USER Mode)..................................................................... 31

1.19.1. Basic Controls........................................................................................ 31

1.19.2. Advanced Controls................................................................................. 33

1.19.3. Configuration.......................................................................................... 44

1.19.4. Maintenance .......................................................................................... 48

1.19.5. About...................................................................................................... 57

1.20. iNetVu™ Menus (CONFIG Mode)................................................................. 60

1.20.1. Configuration.......................................................................................... 60

1.20.2. Advanced Configuration Menu............................................................... 61

1.21. System Demo and Test................................................................................. 63

1.22. Advanced Maintenance Menu....................................................................... 65

Appendix 1: Default Limits and Data............................................................................... 68

Appendix 2 : Windows Vista/W7 User UAC Settings ...................................................... 70

C-Com Satellite Systems Inc Page 6 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

Appendix 3: Using the Reference Satellite Option .......................................................... 71

Appendix 4: USB Drivers Installation .............................................................................. 75

Appendix 5: Declaration of Conformity............................................................................ 79

C-Com Satellite Systems Inc Page 7 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

Revision Notes

The table below records the current version status of this document and any changes

from the previous versions.

Rev. Date Edited By Description

1.0.1 04/11/2008 A. Cheikhali Document Creation

1.0.2 1/13/2009 A. Cheikhali iDirect Broadcast and Reference Satellite

Addition

1.0.3 2/6/2008 A. Cheikhali Reference Satellite Procedure Added

1.0.4 2/20/2008 A. Cheikhali Released with 6.4.1

1.0.5 8/11/09 A. Cheikhali Updated default table values

1.0.6 08/23/2011 A. Kader Updated for release with 6.5.1

Proprietary Notice: This document contains information that is proprietary and

confidential to C-Com Satellite Systems, Inc., and is intended for internal use

only. No part of this document may be copied or reproduced in any way, without

prior written permission of C-Com Satellite Systems, Inc.

C-Com Satellite Systems Inc Page 8 of 79

Introduction

Fig. 1: INetVu™ 5000 Controller

Designed to interface with a growing number of Satellite Modems, VSATs, and DVB-

RCS Receivers, the iNetVu™ 5000 Controller is an easily configurable and operated

unit.

It features Automatic Operations such as Find Satellite and Stow Antenna, as well as the

ability to manually move the Antenna for cross-pol testing, demonstrations, or

installations.

The iNetVu™ DVB-S Tuner Kit is an optional kit addition to the iNetVu™ 5000

Controller. Easily installed, the iNetVu™ DVB-S Tuner will speed up satellite acquisitions

to less than 2 minutes. Once an integrated part of the iNetVu 5000 Controller, the

iNetVu™ DVB-S Tuner works on all iNetVu antennas.

This high performance addition to the iNetVu™ 5000 Controller is programmable to any

DVB-S Satellite and also features a list of pre-configured satellites for the user to select

from.

The iNetVu™ DVB-S Tuner Kit can be used as a stand-alone receiver or as an integral

component of existing service / modem integrations.

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

C-Com Satellite Systems Inc Page 9 of 79

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

Specifications

iNetVu™ 5000C Controller

Dimensions 10.5” x 6” x 1.5” (27cm x 16cm x 4 cm)

Weight 2 lbs (1kg)

Operation Temperature 32F to 122F (0C to 50C)

Elevation Output 12VDC, 12 A (Max.)

Azimuth Output 12VDC, 8 A (Max.)

Polarization Output 12VDC, 2 A (Max.)

Fuse Type Blade-type Automotive, Fast-acting (15 A, 10 A, 5 A)

Power Input 12VDC @ 12.5 A (Min.)

Idle Power Consumption 12VDC @ 500 mA

Power Connector 4 Position 5.08mm Terminal Block

Motor Control Connector 8 Position 5.08mm Terminal Block

Signal Input Female DB26 Connector

GPS Connector SMA (Sub-Miniature Version A)

Rx Connector Type F RG6

PC Interface USB or DB9 Serial Connector

Tuner Specifications

RF Input Range: 950MHz to 2150MHz

Input Dynamic Range: -75dBm to –25dBm

Input/Output Impedance: 75 Ω

Symbol Rate: 1 to 45Msps

Specification

Item

Min Typ Max Unit

Condition

Frequency 950 . 2150 MHz .

Return Loss 6 10 . dB 950MHz to 2150MHz

Noise Figure . 6 10 dB Maximum Gain

Loop Through Gain -2.0 . 4.0 dB .

Input Dynamic Range -75 . -25 dBm .

IMD3 40 .. . dBc Desired & undesired input

Level are -25dBm

Local Leakage . -80 -70 dB 950MHz to 2150MHz

10KHz . -84 . dBc/Hz .

Phase Noise

100KHz . -105 . dBc/Hz .

C-Com Satellite Systems Inc Page 10 of 79

Physical

iNetVu™ 5000 Controller User Manual

Revision 1.0.6

Front Panel

LEDs Automatic

Control

Buttons

Reset

Button

GPS

Antenna

Interface

RF RX

Receive

signal

input

MOTOR

Interface for

Motor Control

Cable

Power Input

DC Power Input

and Switch

USB

SENSORS

26-pin

Interface

for Sensor

Cable

COM

Serial Port

Interface

USB

Interface

Fig. 2: iNetVu™ 5000 Front and Rear Panel

Autres manuels pour 5000

Table des matières

Manuels Système de télévision par satellite populaires d'autres marques

Dish TV

Dish TV DVB-S6800PLUS Manuel utilisateur

Avermedia

Avermedia AVer3D R889 Manuel utilisateur

Kathrein

Kathrein MobiSet 2 Digital CAP 600 Manuel utilisateur

KVH Industries

KVH Industries TracVision R5SL Manuel utilisateur

Philips

Philips DSX 5250 Manuel utilisateur

Winegard

Winegard RMFLDM4 Manuel utilisateur

DefineSat

DefineSat VM55 Manuel utilisateur

Dish Network

Dish Network 112182 Manuel utilisateur

Thrane&Thrane

Thrane&Thrane sailor 60 Manuel technique

KVH Industries

KVH Industries TracVision L2 Manuel utilisateur

KVH Industries

KVH Industries TracVision TV1 Manuel utilisateur

JRC

JRC NJT8304 Series Manuel utilisateur

Bell

Bell EXPRESSVU Manuel utilisateur

Promax

Promax SATHUNTER Manuel utilisateur

SatKing

SatKing PRO MAX Manuel utilisateur

KVH Industries

KVH Industries TracVision M5 Manuel utilisateur

KVH Industries

KVH Industries TracVision R5SL Manuel utilisateur

Dish Network

Dish Network Satellite Television Manuel utilisateur

iNetVu 5000 Manuel utilisateur

Manuels Système de télévision par satellite populaires d'autres marques