Thrane&Thrane Sailor 60 Manuel technique

Document Name: SAILOR_60_90_Satellite_TV_Create_a_New_Satellite_List Revision:

Introduction: This document describes how a new satellite list can be generated for a new coverage area for the

SAILOR 60 and SAILOR 90 Satellite TV Antennas. This is needed to be done when the SAILOR

Satellite TV antenna is going to be used outside Northern Europe region which is the factory default

satellite list.

Description:

Install the NavSat PC program and USB driver for the SAILOR Satellite TV antenna.

Connect the USB cable from the PC to the SAILOR Satellite TV ACU and set the ACU in PC override

mode.

Start the PC program NavSat and press the Satellites button. See figure 1 below.

Figure 1: NavSat Main Window

The window with the satellite list will show. See figure 2 below.

TECHNICAL DOCUMENT

SAILOR 60/90 Satellite TV – Create a New Satellite List

Technical Document New Satellite List Page 2/9

Figure 2: Satellites Window

Press the Sat Id button to see the Sat Id window shown in figure 3 below.

Figure 3: Sat Id window

Technical Document New Satellite List Page 3/9

Delete all the satellites that will not be used for the new operating region of the SAILOR Satellite TV

Antenna. These are done by high-lighting each satellite and press the Delete button. One by one.

The SATELLITES list in Sat Id window shown in figure 3 will now be empty or only contain the rest of

the satellites that is valid for the new operating region.

Now decide which satellites the SAILOR satellite TV antenna is going to use in the new operating

region.

Go to www.lyngsat.com or www.kingofsat.com and lookup the satellite names and position, and write

a list of the desired satellites. One of the satellites needs to be entered as a reference with following

details filled in:

•Name of satellite

•Position

•Transponder Frequency

•Symbol Rate (SR)

•Forward Error Correction (FEC)

•Network ID codes (NID).

The reference satellite’s transponder must be:

•Horizontal polarised

•In the High frequency band (between 11700 – 12750 MHz)

This is because the built-in DVB decoder in the antenna is using that Horizontal-High signal to

determine the NID for the satellites.

The next part will show an example of how a new list of satellites can be generated, using one

satellite as reference (Thor). See example of satellites and their data in figure 4 below:

Figure 4: New satellite list

Technical Document New Satellite List Page 4/9

Enter the reference satellite. In this case Thor as shown in figure 5 below.

Satellite: THOR, Position: W0.8, Polarisation: 0, InView: YES, Usable: YES, Tracking Mode: A(Auto)

Figure 5: New satellite added.

Press New Satellites button to store Thor in the Satellites list.

Now highlight the newly added satellite and enter its:

Frequency: 12476, SBR: 28000, FEC: 5/6, NID Code: 4369

Figure 6. New added channel

Technical Document New Satellite List Page 5/9

Press the New Channels button to save it in the Channels list. See figure 6 above.

The rest of the satellites (Astra_2, Sirius_4, and Hotbird) are added just like the Thor satellite was

added, but without their frequencies, SBR, FEC and NID Codes because the satellites will be

scanned for these information automatically with reference to Thor’s position on the sky.

After adding the rest of the satellites to the satellite list:

1. Press Close button to go back to the main window.

2. Press Satellites button to see the list of satellites.

Note: Thor is the reference satellite. See figure 7 below.

Figure 7: Satellite list

1. Select Thor (highlight it).

2. Press the Set Satellite button to make the SAILOR Satellite TV antenna track for this

satellite. The main window will appear.

3. Press the Auto button in the MANUAL CONTROL panel.

4. Wait until the STATUS reads TRACKING, CONFIRMED for the Thor satellite. See figure 8

below.

Technical Document New Satellite List Page 6/9

Figure 8: Tracking - Confirmed

1. Go to Satellites – Sat Id.

2. Highlight Thor satellite

3. Press Scan Sat button.

A new window will appear where it is possible to set the symbol rate for the satellite that needs to be

scanned. Only in special cases this needs to be altered. Use the default value 15 Msymb/s.

Press the Start Scan button. See figure 9 below.

Figure 9: Set Symbol rate

The SAILOR Satellite TV antenna will now start to scan the Thor satellite for available Horizontal

High transponders and write them into a list of SCANNED CHANNELS.

Wait until it reads SatScan – Finished in the window’s top bar. See figure 10 below.

Technical Document New Satellite List Page 7/9

Figure 10: Scanned Channels

Store some channels for the satellite by highlighting the transponder and press the Add button. Add

the ones with best (lowest) BER.

The selected channels and NID codes are used to locate the satellite in order to confirm exact

pointing direction and satellite. As many satellites have beams directed at different areas, it is

possible to enter several NID codes and channels per satellite. Using several channels and NID

codes increases the probability of a correct identification under difficult reception conditions but can

prolong the scanning time as well. It is therefore recommended to limit the number of channels and

NID codes to about 5-10 per satellite. See example of the chosen channels in figure 11 below.

Technical Document New Satellite List Page 8/9

Figure 11: Chosen channels

1. Press Close button to close the satellites window.

2. Press Close button to enter the main window.

3. Press Auto button in the MANUAL CONTROL panel to make the SAILOR Satellite TV

antenna to track Thor satellite.

4. Wait until it reads TRACKING, CONFIRMED.

5. Press Satellites button.

6. Highlight next satellite in the list.

7. Press the Set Satellite button.

Immediately after it has been noticed that the antenna has turned to the direction of the next satellite,

press Manual button in the MANUAL CONTROL panel.

1. Press the Satellites button.

2. Press the Sat Id button.

3. Highlight the satellite that the antenna is directed to now.

4. Press the Scan Sat button.

5. Press the Start Scan button to scan for the available channels on this satellite.

When the scanning is finished, select 5-10 channels same way as it was done for the reference

satellite (Thor).

Press Close button when the channels are added.

Press the Close button on the Satellites window to get back to the main window.

Press the Auto button to track the new satellite using the selected channels.

Same procedure is used for the rest of the satellites in the list.

Technical Document New Satellite List Page 9/9

When done:

1. Press Satellites button

2. Press Sat Id button

3. Press Save list button

4. Choose a filename and folder to store the new satellite list.

This needs to be done once for each region the SAILOR Satellite TV antenna is going to be used at.

Then when re-entering one of the regions the only thing that needs to be done is to:

1. Press Satellites button

2. Press Sat Id button

3. Press Open List button

4. Choose the satellite file for new region.

The antenna will now be able to track on the satellites for the new region.

Information in this document is subject to change without notice and

does not represent a commitment on the part of Thrane & Thrane A/S.

2010

Autres manuels pour sailor 60

Ce manuel convient aux modèles suivants

Manuels Système de télévision par satellite populaires d'autres marques

Dish TV

Dish TV DVB-S6800PLUS Manuel utilisateur

Avermedia

Avermedia AVer3D R889 Manuel utilisateur

Kathrein

Kathrein MobiSet 2 Digital CAP 600 Manuel utilisateur

KVH Industries

KVH Industries TracVision R5SL Manuel utilisateur

Philips

Philips DSX 5250 Manuel utilisateur

Winegard

Winegard RMFLDM4 Manuel utilisateur

DefineSat

DefineSat VM55 Manuel utilisateur

Dish Network

Dish Network 112182 Manuel utilisateur

KVH Industries

KVH Industries TracVision L2 Manuel utilisateur

KVH Industries

KVH Industries TracVision TV1 Manuel utilisateur

JRC

JRC NJT8304 Series Manuel utilisateur

Bell

Bell EXPRESSVU Manuel utilisateur

Promax

Promax SATHUNTER Manuel utilisateur

SatKing

SatKing PRO MAX Manuel utilisateur

KVH Industries

KVH Industries TracVision M5 Manuel utilisateur

KVH Industries

KVH Industries TracVision R5SL Manuel utilisateur

Dish Network

Dish Network Satellite Television Manuel utilisateur

Uniden

Uniden SQ530 Manuel utilisateur

Thrane&Thrane sailor 60 Manuel technique

Manuels Système de télévision par satellite populaires d'autres marques