Indy R4600PC Manuel utilisateur

Indy™R4600PC™133 MHz and

R4400SC™175 MHz

CPU Upgrade Installation Guide

Document Number 007-9219-003

Indy™R4600PC™133 MHz and R4400SC™175 MHz

CPU Upgrade Installation Guide

Document Number 007-9219-003

CONTRIBUTORS

Written by Judy Muchowski

Illustrated by Dany Galgani, Maria Mortati

Production by Chris Everett

Cover design and illustration by Rob Aguilar, Rikk Carey, Dean Hodgkinson,

Erik Lindholm, and Kay Maitz

This document contains proprietary and conﬁdential information of Silicon

Graphics, Inc. The contents of this document may not be disclosed to third parties,

copied, or duplicated in any form, in whole or in part, without the prior written

permission of Silicon Graphics, Inc.

RESTRICTED RIGHTS LEGEND

Use, duplication, or disclosure of the technical data contained in this document by

the Government is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software clause at DFARS 52.227-7013 and/

or in similar or successor clauses in the FAR, or in the DOD or NASA FAR

Supplement. Unpublished rights reserved under the Copyright Laws of the United

States. Contractor/manufacturer is Silicon Graphics, Inc., 2011 N. Shoreline Blvd.,

Mountain View, CA 94039-7311.

Silicon Graphics is a registered trademark and Indy and Indy Cam are trademarks of

Silicon Graphics, Inc.

iii

Contents

The Upgrade Package 2

Installing the Software 2

Turning Off Your Indy Workstation 3

Removing the Top Cover 4

Attaching the Wrist Strap 5

Checking Your System’s PROM Version: R4600PC 133 MHz Upgrade 6

Replacing the PROM Chip 8

Removing the GIO Option Board 8

Removing the Graphics Board 10

Replacing the PROM Chip 14

Replacing the Graphics Board 18

Replacing the GIO Option Board 20

Replacing the CPU Module 23

Replacing the Cover 26

Turning on the Workstation 27

Product Support 28

List of Figures

Figure 1 Turning off the Indy workstation 3

Figure 2 System power off notifier 3

Figure 3 Removing the top cover from the Indy workstation 5

Figure 4 Okay to Power Off Notifier 6

Figure 5 Starting Up the System Notifier 7

Figure 6 Locating the GIO option board 9

Figure 7 Removing the screws from the rear of the workstation 9

Figure 8 Removing the screws from the GIO option board 10

Figure 9 Removing the screws from the graphics board’s

I/O connector 11

Figure 10 Removing the screws from the graphics board 12

Figure 11 Disconnecting the graphics board from the

system board 13

Figure 12 Locating the PROM chip on the system board 14

Figure 13 Removing the PROM chip 15

Figure 14 Lining up the PROM chip 16

Figure 15 Pressing the PROM chip into the socket 17

Figure 16 Connecting the graphics board to the system board 18

Figure 17 Replacing the screws on the graphics board’s

I/O connector 19

Figure 18 Inserting the screws on the graphics board 19

Figure 19 Inserting the GIO board’s I/O connector through

the backplane 20

Figure 20 Inserting the screws from the rear of the workstation 21

Figure 21 Installing a single-width GIO option board 22

Figure 22 Locating the CPU module 23

Figure 23 Removing the two screws from the CPU module 24

Figure 24 Disconnecting the CPU module 24

Figure 25 Installing the CPU module 25

Figure 26 Replacing the top cover on the Indy workstation 26

Figure 27 Turning on the Indy workstation 27

Upgrading the Indy Workstation CPU

This manual explains how to install the CPU upgrade on an Indy

workstation.

Note: If you received a CD with the upgrade, you must install the software

ﬁrst. Read the software release notes on the CD for software installation

instructions before installing the hardware.

To install the hardware, you will complete these steps:

•Shut down the system.

•Remove the cover.

•Remove and replace the PROM chip on the system board. (If you are

upgrading to an R4600PC 133 MHz CPU, you may not have to replace

the PROM. See the section “Checking Your System’s PROM Version:

R4600PC 133 MHz Upgrade”on page 6.)

•Remove and replace the CPU module.

•Replace the cover and restart your system.

Read through this guide ﬁrst before starting the upgrade. If you ﬁnd a term

you haven’t seen before, see your workstation’sOwner’s Guide. The glossary

contains deﬁnitions of many of the terms used in this guide.

Caution: Make sure you have a full backup of your system before powering

down and installing the upgrade. For instructions on backing up your

system, choose “Online Books”from the Help toolchest. Then select the

Personal System Administration Guide and search for “Backing Up and

Restoring Files.”

Upgrading the Indy Workstation CPU

The Upgrade Package

Your upgrade package includes all of the following items. If anything is

missing, contact your sales representative.

•PROM chip in an antistatic bag

•CPU module in an antistatic bag

•open-ended wrench to remove standoffs and hexnuts

•Phillips screwdriver

•chip removal tool to remove the PROM chip

•anti-static wrist strap

•Indy R4600PC 133 MHz and R4400SC 150 MHz CPU Upgrade Installation

Guide (this manual)

•CD (not in all upgrades)

In addition, some upgrade packages include a system label to attach to the

underside of the Indy workstation.

Installing the Software

If you received a CD with the upgrade, read the release notes on the CD for

instructions on installing the software. Install the software before installing

the hardware.

Turning Off Your Indy Workstation

Press and release the power button on the front of the workstation, as shown

in Figure 1, to power off the system.

Note that it’s not necessary to shut down the system software before

pressing the power button.

Figure 1 Turning off the Indy workstation

The notiﬁer shown in Figure 2 appears on your screen within a few seconds

and the LED blinks green and amber. Then the system powers off

automatically within the next minute.

Figure 2 System power off notiﬁer

Power button

Upgrading the Indy Workstation CPU

Removing the Top Cover

Follow these steps to remove the top cover of your Indy workstation:

1. If the monitor is on top of the workstation, move it to one side.

Caution: Monitors are very heavy. Have someone help you move it.

2. Disconnect the following cables from the back of the Indy workstation:

•power cable

•monitor cable

•IndyCam™cable (if connected)

•EtherNet AUI cable (if connected)

Disconnecting the IndyCam and EtherNet AUI cables is optional.

Removing them gives you more room when removing the screws on

either side of the graphics board connector.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur