In.hub HUB-GM200 Manuel utilisateur

USER MANUAL

IoT Gateway

HUB-GM200

Version 1.1 / 26.06.2023

Table of contents

1Legal Notes ............................................................................................................................... 3

2General information................................................................................................................. 5

2.1 Scope of delivery ............................................................................................................................................5

2.2 General instructions for use ........................................................................................................................5

2.3 Intended use....................................................................................................................................................5

2.4 Safety requirements ......................................................................................................................................5

2.5 Network Security ............................................................................................................................................6

2.6 Disposal ............................................................................................................................................................6

2.7 Service and support.......................................................................................................................................6

3Product information ................................................................................................................ 7

3.1 Use cases .........................................................................................................................................................7

3.2 Hardware - Structure and interfaces ........................................................................................................8

3.3 LED display ......................................................................................................................................................9

3.3.1 LED device status (red-green) .......................................................................................................9

3.4 SIINEOS - System Software.........................................................................................................................9

4Installation ...............................................................................................................................10

4.1 Mounting and dismounting the module at the DIN rail ....................................................................... 10

4.2 Mounting add-on modules ..........................................................................................................................11

5Commissioning ........................................................................................................................12

5.1 Interfaces of the HUB-GM200 ................................................................................................................... 12

5.1.1 USB ..................................................................................................................................................... 12

5.1.2 Power supply.................................................................................................................................... 12

5.1.3 Ethernet 1 and Ethernet 2 ............................................................................................................. 12

5.1.4 CAN..................................................................................................................................................... 13

5.1.5 RS485.................................................................................................................................................14

5.1.6 IO1 and IO2........................................................................................................................................ 15

5.1.7 LED display.......................................................................................................................................16

5.1.8 Backplane bus..................................................................................................................................16

5.2 Connecting the HUB-GM200 to the power supply................................................................................ 16

6First steps with SIINEOS........................................................................................................17

6.1 Connecting the HUB-GM200 with your PC ............................................................................................. 17

6.2 Logging in to SIINEOS .................................................................................................................................. 18

6.3 Checking the SIINEOS version ................................................................................................................... 19

6.4 Updating SIINEOS ........................................................................................................................................ 20

7Technical data .........................................................................................................................21

8EU Declaration of Conformity .............................................................................................. 22

Legal Notes

1Legal Notes

Warning concept

This manual contains information that you must observe for your personal safety and to

prevent damage to property. Depending on the hazard level, the warnings are presented in

decreasing order as follows:

DANGER

Indicates a direct hazard for humans. Irreversible injuries or death willl result if not

observed.

WARNING

Indicates a recognizable hazard for humans. Irreversible injuries or death may result if

not observed.

CAUTION

Indicates a recognizable hazard for humans or possible damage to property. Can lead to

reversible injuries or damage to property if not observed.

ATTENTION

Note on possible damage to property. May cause damage to property if not observed.

NOTE: Under Note you will find tips, recommendations, and useful information on

specific action steps and facts.

If several hazard levels occur, the warning for the highest level is always used. If the

triangle warning against personal injury is used in a warning, then a warning against

property damage can also be added to the same hazard hint.

Qualified personnel

The product associated with this documentation may only be handled by personnel who

are qualified for the respective task. Furthermore, the product may only be handled in

compliance with the associated documentation and the safety and warning instructions

contained therein. Due to their training and experience, qualified personnel are equipped to

recognize and avoid potential hazards when handling these products.

Required basic knowledge

Knowledge of personal computers, operating systems, and programming is required.

General knowledge in the field of automation technology is recommended.

Legal Notes

Safety information

Before commissioning the product, be sure to read this section carefully and observe the

corresponding notes in the manual. Always keep the Instruction Manual within reach.

Intended use

in.hub products may only be used for the applications specified in the corresponding

technical documentation.

If third-party products and components are used, they must be recommended or approved

by in.hub.

Proper storage, installation, commissioning, and operation are essential for the correct and

safe operation of the product.

The permissible environmental conditions must be complied with. Notes in the associated

documentation must be observed.

Trademarks

All names marked with the protective note “®” are registered trademarks. Other names in

this document may be trademarks whose use by third parties for their own purposes may

infringe the rights of the owners.

Disclaimer

The content of this publication has been checked for conformity with the hardware

described. Nevertheless, discrepancies cannot be ruled out, so we do not assume any

liability for its completeness and correctness. The information in this publication is

reviewed on a regular basis. Any corrections needed will be included in the following

editions.

General information

2General information

This Instruction Manual contains information for commissioning and using the HUB-GM200

gateway.

The manual is intended for installers, programmers, and testers who commission the

gateway and connect it to other units (automation systems, mobile terminals, personal

computers, etc.), and for service technicians who install extension modules or perform

error analyses.

2.1 Scope of delivery

1 x HUB-GM200

1 x SIINEOS system software

1 x Backplane bus connector

1 x HUB-GM200 Instruction Manual (PDF)

1 x SIINEOS User Manual (PDF)

2.2 General instructions for use

in.hub GmbH assumes no liability for malfunctions of the device resulting from improper

handling, mechanical damage, incorrect application, and use other than for the intended

purpose. Improper handling of the device can significantly reduce the service life of the

product.

2.3 Intended use

The devices are intended exclusively for use in the industrial sector and are used to

monitor and control machines, systems, and processes. With the help of the connection

options provided, process data can be recorded, processed, controlled, and analyzed.

2.4 Safety requirements

The product should be handled in accordance with the following DIN standards:

•DIN EN 61340-5-1:2017-07 Electrostatics – Part 5-1: Protection of electronic

components against electrostatic phenomena – General requirements

•DIN EN 61010-1:2020-03 Safety requirements for electrical equipment for measurement,

control, and laboratory use - Part 1: General requirements

•DIN EN 60664-1:2008-01 Insulation coordination for equipment within low-voltage

systems - Part 1: Principles, requirements, and tests

General information

2.5 Network Security

Please keep in mind that the product does not communicate encrypted within the internal

network. Therefore, protect your network against unauthorized access from outside! The

integration into a network with Internet access must be carried out with special care. For

this, urgently talk to your system administrator in advance.

2.6 Disposal

he device must be disposed of properly. It does not belong in the normal

household waste.

2.7 Service and support

If you have any questions about specific use cases or about technical parameters,

please contact us.

Email: service@inhub.de

Phone: +49 371 5347 825 (Technical sales stuff)

These details will connect you with the appropriate contact.

Product information

3Product information

The IoT gateway HUB-GM200 was specially designed for use in industrial environments. It

has a variety of different interfaces that allow sensors and actuators to connect directly to

the gateway.

The HUB-GM200 is primarily used on the sales floor to control and connect the field level

and the control level with the operational-management level and the company level. It is

also used for individual monitoring, specifically to monitor, manage, and control processes

in a closed loop.

3.1 Use cases

The HUB-GM200 is ideal for:

•In-process parameter monitoring for

oPreventive maintenance

oAcquisition of machine data

oCondition monitoring and yield monitoring on production lines

oMonitoring of environmental influences on the process for compliance with

standard guidelines and occupational health and safety regulations (including

temperature, humidity, particle concentration, corrosion)

•Soft-SPS (soft programmable logic controller)

•Use as a process-control computer and traceability server

•Use as a remote access point on machines and systems for remote maintenance via

VPN or VNC (cloud service)

•Process monitoring using machine learning / AI algorithms

Product information

3.2 Hardware - Structure and interfaces

Fig. 1: Side views and front view of the HUB-GM200

1 Device-specific information is encoded in a barcode:

HW: Hardware revision number

S/N: in.hub-internal serial number

MAC: Hardware address of the Ethernet 1 and 2 network adapters

2 Backplane bus

3 Ethernet 2

4 Ethernet 1

5 CAN bus

6 RS485

7 LEDs for displaying the operating status

8 USB1 (Host) and USB2 (Device)

9 Protective cap

Can be opened upwards.

10 USB3 (Host)

Product information

11 Input/Output 1

12 Input/Output 2

13 24V DC power supply

14 Clamping device for DIN-rail installation

3.3 LED display

The three LEDs on the front panel of the device indicate the following status:

Fig. 2: LED status display on the front of the HUB-GM200

1 Device status

2 Function freely configurable in SIINEOS

3 Function freely configurable in SIINEOS

3.3.1 LED device status (red-green)

LED behavior Color Meaning

LED off Device is out of service

Flashing in heartbeat

mode 2 Hz

Green Module ready for operation

Permanent glow Green Error in the boot process

1 Hz flashing Red Device error

3.4 SIINEOS - System Software

The HUB-GM200 uses the Linux-based operating system SIINEOS to run InCore & Docker

Apps. SIINEOS is accessible via a management console (SMAC) and can be configured

there. All network parameters are also set up here to enable communication with other

components of the network.

Installation

4Installation

The HUB-GM200 is intended for installation on a DIN rail compliant with

DIN EN 60715:2017.

•Always switch the power supply off.

WARNING Electrical shock due to conductive contamination can cause

physical injury!

Avoid conductive contamination.

Only install devices in a control cabinet of the appropriate

protection class.

•When inserting several modules, start on the left with a CPU / interface module, a

system power supply, or main power supply.

•RECOMMENDATION: For ease of installation, maintain a minimum distance of 25 mm

between cable channel and housing edge (top and bottom).

4.1 Mounting and dismounting the module at the DIN rail

1. Switch off the power supply.

2. Rotate the module so that the metal clamping device is facing downward.

3. Hold the module at an angle to the DIN rail.

The recess on the back of the module is located above the clamping device.

4. Push the module onto the DIN rail until the clamping device audibly clicks into place.

5. After installation, check that the device is firmly fixed and straight on the DIN rail.

6. To dismount, pull down the metal clamping device with a screwdriver and remove the

module from the DIN rail.

Fig. 3: Disassembly of the module from the DIN rail (example)

Table des matières

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur

in.hub HUB-GM200 Manuel utilisateur

Manuels Porte populaires d'autres marques