IFM Efector200 O6P2 Manuel utilisateur

Operating instructions

Retro-reflective sensor

O6P2

O6P200 / 01 01 / 2015

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Functions and features

In conjunction with a prismatic reflector or reflective tape the retro-reflective sen-

sor detects objects and materials without contact and indicates their presence by

a switching signal.

3 Installation

►Fit the prismatic reflector or the reflective tape behind the object to be detected.

►Align the retro-reflective sensor to it and secure it to a bracket.

Maximum range only with accurate alignment.

4 Operating and display elements

1: LED yellow - switching output active

2: Setting potentiometer „sensitivity“

3: LED green - operation, stability indication

4: Selector „output function“

4.1 Stability indication

The green LED is lit when the supply voltage is applied and there is sufficient

excess gain. Under these conditions the sensor receives a stable signal.

stable signal switch point stable signal

Light-on mode

LED green on off off on

LED yellow on on off off

Dark-on mode

LED green on off off on

LED yellow off off on on

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Ensure voltage supply to EN 50178.

►Disconnect power.

►Connect the unit as follows:

5.1 PNP

Connector M12 pigtail Cable *





















Connector M8 3-pin Connector M8 4-pin





















* Core colours: BN = brown, BU = blue, BK = black

5.2 NPN

Connector M12 pigtail Cable *

L+

Connector M8 3-pin Connector M8 4-pin

L+

* Core colours: BN = brown, BU = blue, BK = black

6 Settings

6.1 Set the output function

►Setting D: dark-on mode

►Setting L: light-on mode

6.2 Set the sensitivity

►Increase sensitivity: turn the setting

screw of the potentiometer clockwise.

►Decrease sensitivity: turn the setting

screw of the potentiometer anti-

clockwise.

7 Operation

►Check whether the unit operates correctly.

> The green LED is lit when the supply voltage is applied and there is sufficient

excess gain.

> Dark-on mode: the output is switched / the yellow LED is lit when an object is

detected.

> Light-on mode: the output is switched / the yellow LED is lit when no object is

detected.

8 Maintenance, repair, disposal

►Keep the lens of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic parts.

►After use dispose of the unit in an environmentally friendly way in accordance

with the applicable national regulations.

Faulty sensors must only be repaired by the manufacturer.

Technical data and further information at unter www.ifm.com

Table des matières

Autres manuels IFM Accessoires

IFM

IFM Efector 180 IX5030 Manuel utilisateur

IFM

IFM SB1 Series Manuel utilisateur

IFM

IFM PN422 Series Manuel utilisateur

IFM

IFM PN00 A Series Manuel utilisateur

IFM

IFM Efector500 PY7102 Manuel utilisateur

IFM

IFM SBY2 Series Manuel utilisateur

IFM

IFM LI513 Series Manuel utilisateur

IFM

IFM PN3 Series Manuel utilisateur

IFM

IFM O1D120 Manuel utilisateur

IFM

IFM efector 200 OGH Manuel utilisateur

IFM

IFM O5H5xA Series Manuel utilisateur

IFM

IFM PL205 Series Manuel utilisateur

IFM

IFM MVQ101 Guide d'application

IFM

IFM LDL100 Manuel utilisateur

IFM

IFM LW2720 Manuel utilisateur

IFM

IFM JD Series Guide d'application

IFM

IFM Efector 160 LK8 Manuel utilisateur

IFM

IFM SB4 Series Manuel utilisateur

IFM

IFM PI28 Series Manuel utilisateur

IFM

IFM OGH3 Series Manuel utilisateur

IFM

IFM Ecomat 100 EC2082 Mode d’emploi

IFM

IFM LR7009 Manuel utilisateur

IFM

IFM MN7 S Series Manuel utilisateur

IFM

IFM OJ51 Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

IFM efector200 O6P2 Manuel utilisateur

Manuels Accessoires populaires d'autres marques