IFM Efector 200 OGH Manuel utilisateur

Operating instructions

Diffuse reflection sensor

with background suppression

OGH

701166 / 03 09 / 2005

Function and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switched signal.

Range (r): see type label (value referred to white paper 200mm x 200mm).

Electrical connection

The device shall be supplied from an isolating source and protected by

an overcurrent device such that the limited voltage circuit requirements in

accordance with UL 508 are met.

Isolate power, then connect the unit (see page 5 or type label).

Core colours (for sensors with cable connection): BN = brown, BU = blue, BK =

black.

Programming of the output function (light-on or dark-on) by wiring (see page 5 or

type label).

Installation

Pushbutton

LEDs red, green, yellow

Align the photocell and fasten it to a mounting bracket.

Maximum range is only possible with precise alignment.

Setting of the sensitivity with stationary objects

Activate the programming mode of the unit without object.

Press for about 2s until the red LED flashes.

The red LED goes out; the yellow and green LEDs flash alternately.

The unit is in the programming mode.

If in addition the red LED is lit, the reflection of the background is too intensive (e.g.

reflecting surface). Angle the unit in the horizontal plane until the red LED goes out.

If you continue with step 3 although the red LED is lit, programming is interrupted.

The unit then passes into the operating mode with the setting being unchanged.

Setting without object.

Press once.

The yellow and green LEDs go out for approx. 1s, then flash again alternately.

Setting with object.

Press once.

The yellow and green LEDs go out for approx. 1s, then the green LED is on.

The unit is in the operating mode.

Programming is only possible if you keep to this order (first background, then

object).

If the setting of the sensitivity is not possible (e.g. object signal and

background signal are about the same), the red LED flashes after step

3 for approx. 2s. The unit then passes into the operating mode with the

sensitivity being unchanged.

Setting of the maximum sensitivity

Go into the programming mode (step 1).

Align the unit so that no light is reflected.

Press the setting button twice (see steps 2 and 3).

Locking / Unlocking

Press for 10s

The red LED lights for a short time,

then the yellow and green LEDs flash

alternately;

after 10s the LEDs go out, the unit is

locked.

Press for 10s

After 10s the LEDs go out, locking is

cancelled.

Operation

Check the safe functioning of the diffuse reflection sensor. Display by LEDs.

LED green lights Unit is ready for operation.

LED yellow lights Output is switched.

LEDs yellow + red

Flash alternately, 2 Hz: output short-circuited.

Flash alternately, 1 Hz: internal malfunction,

(output is not switched).

Maintenance

Keep the lens of the sensor free from soiling.

For cleaning do not use any solvents or cleaning agents which could damage the

plastic lenses.

•

Wiring

DC PNP

L+

DC NPN

L+

1L+

L+

Table des matières

Autres manuels IFM Accessoires

IFM

IFM Efector 200 OJ51 Series Manuel utilisateur

IFM

IFM LX Series Manuel utilisateur

IFM

IFM Efector200 OJ51 Series Manuel utilisateur

IFM

IFM Efector 200 O5PG Manuel utilisateur

IFM

IFM SI 5000 Manuel utilisateur

IFM

IFM O1D100 series Manuel utilisateur

IFM

IFM OJ Manuel d'utilisation et d'entretien

IFM

IFM 402946 Manuel utilisateur

IFM

IFM OGD582 Manuel utilisateur

IFM

IFM efector200 OOF Series Manuel utilisateur

IFM

IFM Efector 500 PI30 Manuel utilisateur

IFM

IFM IFS Series Manuel utilisateur

IFM

IFM JN2301 Guide d'application

IFM

IFM OY Series Manuel utilisateur

IFM

IFM SAxx04 Series Manuel utilisateur

IFM

IFM O6H7 Series Manuel utilisateur

IFM

IFM Efector 200 O5 Manuel utilisateur

IFM

IFM OY90 S Series Manuel utilisateur

IFM

IFM LW2120 Manuel utilisateur

IFM

IFM SBU3 Series Manuel utilisateur

IFM

IFM OG Manuel utilisateur

IFM

IFM TS502A Manuel utilisateur

IFM

IFM LX0020 Manuel utilisateur

IFM

IFM PN7160 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

IFM efector 200 OGH Manuel utilisateur

Manuels Accessoires populaires d'autres marques