IFM Electronic Efector200 OGS50 Series Manuel utilisateur

Operating instructions

Through-beam sensor

OGS50x

OGE50x

704071 / 01 02 / 2008

1 Functions and features

The through-beam sensor detects objects and materials without contact and

indicates their presence by a switching signal.

For the range see the type label.

2 Installation

transmitter receiver

Install the receiver (OGE...) and secure it to a bracket.►

Align the transmitter (OGS...) to the receiver and fix it.►

3 Electrical connection

Disconnect power.►

Connect the unit as follows.►

Transmitter

Cable Connector Pin connection

L+ BN pin 1

L- BU pin 3

— — pin 4

— — pin 2

Core colours BN = brown, BU = blue, BK = black

Receiver

Cable Connector Pin connection

L+ BN pin 1

L- BU pin 3

load BK pin 4

— — pin 2

Core colours BN = brown, BU = blue, BK = black

4 Operating and display elements

transmitter receiver

�

  

LED1:

[OUT off]2:

[OUT on]3:

4 Settings

4.1 The receiver is to switch when the object is detected

Position the object.►

receiver transmitter

Press [OUT on] for 2 s.►

The sensitivity is set to the object.>

The LED flashes.>

Remove the object.►

receiver transmitter

Press [OUT off].►

The sensitivity is set without object.>

The LED goes out. The programming is finished.>

4.2

The receiver is not to switch when the object is detected

Position the object (see figure 1) and press [OUT off] for 2►

Remove the object (see figure 2) and press [OUT on].►

The settings can also be carried out first without object (step 1) and then with

object (step 2).

4.3 Programming unsuccessful

LED flashes quickly, 8 Hz.>

Possible causes

Insufficient difference in measurements.•

Max. programming time of 15 min. exceeded.•

4.4 Setting of maximum sensitivity

Align the receiver so that no light is received.►

The receiver is to switch when the object is detected.

First press [OUT on] and then [OUT off].►

The receiver is to switch when the object is not detected.

First press [OUT off], then [OUT on].►

4.5 Locking or unlocking the buttons

The unit can be locked electronically to prevent unintentional settings.

Press [OUT on] and [OUT off] simultaneously for►

10 s.

Acknowledgement is indicated by a change of the>

LED status.

5 Operation

Check whether the sensors operate correctly.►

The receiver LED lights when the switching output is switched.>

6 Maintenance

Keep the lenses of the sensors free from soiling.►

For cleaning do not use any solvents or cleaning agents which could damage►

the plastic lenses.

Technical data and further information at www.ifm.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IFM Electronic Accessoires

IFM Electronic

IFM Electronic SU7000 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 OL Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SM0505 Manuel utilisateur

IFM Electronic

IFM Electronic efector 200 OPU200 Manuel utilisateur

IFM Electronic

IFM Electronic LR3000 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 OM Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 100 series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic efector 250 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 500 PN3 Manuel utilisateur

IFM Electronic

IFM Electronic efector500 PI20 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 OJ5192 Manuel utilisateur

IFM Electronic

IFM Electronic Ecomat 100 CR2102 Guide d'application

IFM Electronic

IFM Electronic PI209 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 160 LK81 Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 100 GM505S Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 O5H Manuel utilisateur

IFM Electronic

IFM Electronic Efector 300 SA1000 Manuel utilisateur

IFM Electronic

IFM Electronic efector160 LI51 Manuel utilisateur

IFM Electronic

IFM Electronic SM7000 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 410 JN2100 Guide d'application

IFM Electronic

IFM Electronic efector 200 OG laser Manuel utilisateur

IFM Electronic

IFM Electronic ecomat100 CR2101 Guide d'application

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur