IFM Electronic Efector 200 OPU200 Manuel utilisateur

Operating instructions

optical fork sensor

OPU200

OPU200 / 00 02 / 2009

Contents

1 Preliminary note....................................................................................................3

1.1 Symbols used.................................................................................................3

2 Functions and features.........................................................................................3

3 Installation ............................................................................................................3

4 Operating and display elements...........................................................................3

5 Electrical connection.............................................................................................4

6 Setting..................................................................................................................5

6.1 Setting of the output function.........................................................................5

6.2 Sensitivity setting...........................................................................................5

7 Operation..............................................................................................................6

8 Maintenance, repair and disposal ........................................................................7

Preliminary note1

Symbols used1.1

►Instruction

> Reaction, result

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

Functions and features2

The optical fork sensor detects objects and materials without contact and indicates

their presence by a switching signal.

Installation3

T: transmitter; R: receiver

Secure the optical fork sensor (OPU...) to a bracket.►

Operating and display elements4

LED yellow1:

output function switch2:

sensitivity potentiometer3:

Electrical connection5

The unit must be connected by a qualified electrician.

The national and international regulations for the installation of electri-►

cal equipment must be adhered to.

Ensure voltage supply to EN 50178, SELV, PELV.►

The following indications apply if there is a UL listing mark on the product:

For use in NFPA 79 applications only. Adapters providing field wiring►

means are available from the manufacturer. Refer to manufacturers

information.

The device shall be supplied from an isolating transformer having a►

secondary Listed fuse rated

a) max 5 amps for voltages 0...20 Vrms (0...28.3 Vp) or

b) 100/Vp for voltages of 20...30 Vrms (28.3...42.4 Vp).

Disconnect power.►

Connect the unit as follows:►

Automatic PNP / NPN detection

DC PNP

L+

pin 1 = L+

pin 3 = L-

pin 4 = load

DC NPN

pin 1 = L+

pin 3 = L-

pin 4 = load

On power up, the unit detects automatically if the switching output is con-

nected to L- (= PNP) or to L+ (= NPN).

Setting6

Setting of the output function6.1

NO NC

A: cover; B: output function switch

Remove the cover (A).1.

Set the output function (NO/NC) via the switch (B) using a screwdriver.2.

Refit the cover (A).3.

Sensitivity setting6.2

The sensor is to switch when the object is detected

Set the setting potentiometer to the lowest sensitivity.►

Position the object to be detected in the detection►

zone.

Increase the sensitivity until the yellow LED lights.►

Remove the object from the detection zone.►

The yellow LED goes out. The setting operation is>

completed.

The sensor is not to switch when the object is detected

Set the setting potentiometer to the highest sensitivi-►

ty. The yellow LED is lit.

Position the object to be detected in the detection►

zone.

Reduce the sensitivity until the yellow LED goes out.►

Remove the object from the detection zone.►

The yellow LED is lit again. The setting operation is>

completed.

Operation7

Check whether the unit operates correctly.►

The yellow LED is lit when the output is switched.>

Maintenance, repair, disposal8

Keep the lens of the sensor free from soiling.►

For cleaning do not use any solvents or cleaning agents which could damage►

the lens.

After use dispose of the unit in an environmentally friendly way in accordance►

with the applicable national regulations.

Faulty sensors must only be repaired by the manufacturer.

Technical data and further information at

www.ifm.com →Select your country →Data sheet direct:

Table des matières

Autres manuels IFM Electronic Accessoires

IFM Electronic

IFM Electronic Efector 200 OI Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SM6004 Manuel utilisateur

IFM Electronic

IFM Electronic efector 500 PM2055 Manuel utilisateur

IFM Electronic

IFM Electronic efector500 PI20 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 300 Manuel utilisateur

IFM Electronic

IFM Electronic O3M151 Manuel du propriétaire

IFM Electronic

IFM Electronic efector 200 O5 Manuel utilisateur

IFM Electronic

IFM Electronic efector 500 PI00 A Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 300 SM7050 Manuel utilisateur

IFM Electronic

IFM Electronic efector100 ID503A Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic LK31xx Manuel utilisateur

IFM Electronic

IFM Electronic LK1022 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 O6T3 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 250 Manuel utilisateur

IFM Electronic

IFM Electronic O1D100 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 500 PP70 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector160 LR7000 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 600 TC7430 Manuel utilisateur

IFM Electronic

IFM Electronic efector 250 O2D22x Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Guide d'installation

IFM Electronic

IFM Electronic efector300 SU9004 Manuel utilisateur

IFM Electronic

IFM Electronic PY2954 Manuel utilisateur

IFM Electronic

IFM Electronic LR3000 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur

IFM Electronic efector 200 OPU200 Manuel utilisateur

Manuels Accessoires populaires d'autres marques