IFM Electronic Efector 200 Manuel utilisateur

Operating instructions

Diffuse reflection sensor with

background suppression

OGH7xx

704076 / 03 06 / 2011

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

IEC 60825-1 : 2007

Complies with 21 CFR 1040.10 except for deviations pursuant to Laser

Notice No. 50, dated June 2007.

Position of the product label Additional label

3 Functions and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range 20 ... 200 mm (on white paper 200 x 200 mm, 90 % remission)

4 Installation



1: LED

2: programming buttons

►Align the diffuse reflection sensor to the object to be detected.

►Secure it to a bracket.

Note:

The objects to be detected are to move transver-

sally to the lens of the sensor.

►In case of other directions of movement

it should be tested before whether safe

switching is guaranteed.

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

DC PNP











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

DC NPN











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

6 Settings

6.1 The sensor is to switch when the object is detected

►Position the object





►Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The LED flashes.

►Remove the object





►Press [OUT off].

> The sensitivity is set without object.

> The LED goes out. The programming is finished.

6.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off] for 2 s.

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

6.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

6.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz.

• Measured value difference too small

• Max. programming time (15 min.) exceeded.

6.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

7 Operation

►Check whether the unit operates correctly.

> The LED lights when the switching output is switched.

8 Maintenance, repair and disposal

►Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at

www.ifm.com→Selectyourcountry→Datasheetdirect:

Autres manuels pour Efector 200

Table des matières

Autres manuels IFM Electronic Accessoires

IFM Electronic

IFM Electronic efector100 GG507S Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SU8000 Manuel utilisateur

IFM Electronic

IFM Electronic VSA003 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic TS502A Manuel utilisateur

IFM Electronic

IFM Electronic SU7000 Manuel utilisateur

IFM Electronic

IFM Electronic efector 200 OIH5 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 200 OJ Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector200 OG Manuel utilisateur

IFM Electronic

IFM Electronic SB 4 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 410 JN2300 Guide d'application

IFM Electronic

IFM Electronic LK1022 Manuel utilisateur

IFM Electronic

IFM Electronic efectro 500 Manuel utilisateur

IFM Electronic

IFM Electronic LK7 Manuel utilisateur

IFM Electronic

IFM Electronic efector200 OJ Manuel utilisateur

IFM Electronic

IFM Electronic EFECTOR 500 PI26 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 410 JN2100 Guide d'application

IFM Electronic

IFM Electronic PN2 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector200 O7H2 Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

IFM Electronic

IFM Electronic efector160 LI214 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 160 LK81 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SM6004 Manuel utilisateur

IFM Electronic

IFM Electronic efector 190 DTE820 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur