IDEAL Classic M3050 Manuel utilisateur

2classic m - User's

Introduction

The classic m is a wall mounted, room sealed, non

condensing boiler featuring full sequence automatic spark

ignition and fan assisted combustion.

Safety

Current Gas Safety (Installation & Use)

Regulations or rules in force.

In your own interest, and that of safety, it is the law

that this boiler must be installed by a CORGI

registered installer, in accordance with the above

regulations.

It is essential that the instructions in this booklet are

strictly followed, for safe and economical operation of

the boiler.

Electricity Supply

The appliance must be efficiently earthed.

Supply 230 V - 50 Hz. The fusing should be 3A.

Connection must be made in a way that allows complete isolation

of the electrical supply - such as a double pole switch, having a

3mm (1/8") contact separation in both poles, or a plug and socket

serving only the boiler and system controls. The means of

isolation must be accessible to the user after installation.

Important Notes

zThis appliance must not be operated without

the casing correctly fitted and forming an adequate seal.

zIf the boiler is installed in a compartment then the compartment

MUST NOT be used for storage purposes.

zUnder NO circumstances should any of the sealed components

on this appliance be used incorrectly or tampered with.

zIf it is known or suspected that a fault exists on the boiler then it

MUST NOT BE USED until the fault has been corrected by a

CORGI registered installer.

Minimum Clearances

Clearances of 165mm (6 1/2") above, 100mm (4") below, 5mm

(1/4") at the sides and 450mm (17 3/4") at the front of the boiler

casing must be allowed for servicing.

To light the boiler

(Refer to Frame 1)

1. CHECK THAT THE ELECTRICITY SUPPLY TO THE BOILER

IS OFF.

2. Set the mains on/off switch (A) to off and the CH thermostat

knob (C ) to maximum.

3. Switch on the electricity supply to the boiler and check that all

external controls, e.g. programmer, room thermostat, etc are

on.

4. Set the mains on/off switch to ON.

The boiler will commence the ignition sequence, supplying heat

to the system when required.

classic m (Natural Gas Models Only)

classic m3050 ............. G.C. Appliance No. 41- 391- 50

classic m5080 ............. G.C. Appliance No. 41- 391- 51

Destination Countries: GB, IE

THE LOG BOOK SHOULD BE COMPLETED AFTER

EACH SERVICE AND KEPT WITH THESE

INSTRUCTIONS.

All CORGI Registered Installers carry a CORGI ID card, and have a registration number. Both should be recorded

in your Benchmark Log Book. You can check your installer by calling CORGI direct on 0156 372 300.

classic m - User's

Operation

In normal operation the control unit display (F) will show the

codes:

O - Standby (no demand for heat)

C - Heat demand being supplied.

During ignition the LED (E) will flash.

During normal running the LED will remain illuminated.

Note. If the boiler fails to light after 3 attempts the fault code 'L' 'F'

will be displayed.

Press and hold the reset button (D) for 2 seconds then release.

The boiler will repeat the ignition sequence. If the boiler fails to

light consult a CORGI registered installer.

Control of water temperature

The boiler controls the central heating radiator temperature to a

maximum of 820C, adjustable via the CH thermostat knob (C).

Approx CH flow temperatures for the boiler thermostat settings

are:

Knob Setting Flow Temperature

0C0F

Minimum 66 150

71 160

77 170

Maximum 82 180

To shut down the boiler

1. For short periods

Set the mains on/off switch (A) to OFF.

2. For longer periods

Set the mains on/off switch (A) to OFF. Switch the electricity

supply to OFF. For longer periods the entire system should be

drained, inlcuding the domestic hot water supply.

To relight the boiler

Repeat the procedure detailed in 'To light the boiler'.

Frost Protection

If no frost protection is provided and frost is likely during a short

absence from home leave the heating controls (if fitted) at a

reduced temperature setting.

For longer periods the entire system should be drained.

If the system includes a frost thermostat then,during cold

weather, the boiler should be turned OFF at the time switch (if

fitted) ONLY. The mains supply should be left switched ON, with

the boiler thermostat left in the normal running position.

Boiler Overheat Thermostat

This thermostat will shut down the boiler in the event of

overheating. Should this occur a fault code 'L' 'A' will be

displayed. Press the reset button (D) and the boiler will relight. If

the fault recurs turn off the boiler and consult a CORGI registered

installer.

CAUTION.

To avoid the possibility of injury during the installation, servicing or cleaning of

this appliance care should be taken when handling edges of sheet steel components.

Ecl 1624

Legend

ABoiler on/off switch

B"Mains on" LED

CCH thermostat knob

DReset button

ELED

FDisplay

BOILER CONTROLS

Ideal Consumer Helpline

Tel: 01482 498 660

Caradon Plumbing Ltd.

pursues a policy of continuing

improvement in the design and

performance of its products. The

right is therefore reserved to

vary specification without notice. June 2001 UIN 156 123 A01

The code of practice for the installation,

commissioning & servicing of central heating systems

Caradon Plumbing Ltd. is a member of the Benchmark

initiative and fully supports the aims of the programme.

Benchmark has been introduced to improve the standards of

installation and commissioning of central heating systems in

the UK and to encourage the regular servicing of all central

heating systems to ensure safety and efficiency.

Caradon Plumbing Ltd.

P.O. Box 103, National Ave,

Kingston upon Hull, HU5 4JN.

Telephone: 01482 492 251 Fax:

01482 448 858. Registration No.

London 322

137.

Escape of gas

Should a gas leak or fault be suspected contact your local gas

supplier without delay.

Do NOT search for gas leaks with a naked flame.

Cleaning

For normal cleaning simply dust with a dry cloth.

To remove stubborn marks and stains use a damp cloth and mild

detergent.

DO NOT use abrasive cleaning materials.

Maintenance

The appliance should be serviced at least once a year by a CORGI

registered installer.

www.idealboilers.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IDEAL Chaudière

IDEAL

IDEAL EVOMAX 2 30 Manuel utilisateur

IDEAL

IDEAL LOGIC Combi E 35 Manuel utilisateur

IDEAL

IDEAL Europa 24 Guide de l'utilisateur

IDEAL

IDEAL F400 Manuel utilisateur

IDEAL

IDEAL Logic HEAT 12 Manuel utilisateur

IDEAL

IDEAL Concord Super Series 4 50 V Manuel utilisateur

IDEAL

IDEAL Mexico Slimline CF3/40 Fiche technique

IDEAL

IDEAL Vogue Combi c26 Manuel utilisateur

IDEAL

IDEAL H12 Manuel utilisateur

IDEAL

IDEAL RS30l RS40 Note de version

IDEAL

IDEAL IDEAL SPRINT RS 75 Manuel utilisateur

IDEAL

IDEAL Concord CXS 40 Guide de l'utilisateur

IDEAL

IDEAL Esprit eco 30 Manuel utilisateur

IDEAL

IDEAL Mexico super RS485 Manuel utilisateur

IDEAL

IDEAL Logic Heat 30 Manuel utilisateur

IDEAL

IDEAL LOGIC+ Combi 24 Manuel utilisateur

IDEAL

IDEAL EVOMOD 250 Manuel utilisateur

IDEAL

IDEAL Concord CXA120 Guide de l'utilisateur

IDEAL

IDEAL Viceroy GT 8 Manuel utilisateur

IDEAL

IDEAL Classic LXFF 230 Manuel utilisateur

IDEAL

IDEAL LOGIC CODE COMBI ESP1 26 Manuel utilisateur

IDEAL

IDEAL LOGIC+ SYSTEM2 S15 Guide de l'utilisateur

IDEAL

IDEAL he15 Manuel utilisateur

IDEAL

IDEAL Evomax 30 Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur