IDEAL Vogue Combi c26 Manuel utilisateur

When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and

performance speciﬁcation that we require.

Do not use reconditioned or copy parts that have not been clearly authorised by Ideal.

USER GUIDE

Vogue Combi c26, c32, c40

c26 G.C. Appliance No. 47-348-99

c32 G.C. Appliance No. 47-348-98

c40 G.C. Appliance No. 47-348-97

THE BENCHMARK SERVICE INTERVAL RECORD MUST BE COMPLETED AFTER EACH SERVICE

Ideal Stelrad Group is a member of the Benchmark scheme and fully supports the aims of the

programme. Benchmark has been introduced to improve the standards of installation and commissioning

of central heating systems in the UK and to encourage the regular servicing of all central heating systems

to ensure safety and efciency.

Natural Gas only

Vogue Combination boiler

INTRODUCTION

The vogue is a wall mounted, room sealed, condensing combination boiler, featuring full sequence automatic spark ignition and

fan assisted combustion.

Due to the high efciency of the boiler, condensate is produced from the ue gases and this is drained to a suitable disposal point

through a plastic waste pipe at the base of the boiler. A condensate ‘plume’ will also be visible at the ue terminal.

The vogue is a combination boiler providing both central heating and instantaneous domestic hot water.

SAFETY

Current Gas Safety (Installation & Use) Regulations or rules in force.

In your own interest, and that of safety, it is the law that this boiler must be installed by a Gas Safe Registered Engineer, in

accordance with the above regulations.

In IE, the installation must be carried out by a Registered Gas Installer (RGII) and installed in accordance with the current edition

of I.S. 813 “Domestic Gas Installations”, the current Building Regulations and reference should be made to the current ETCI

rules for electrical installation.

It is essential that the instructions in this booklet are strictly followed, for safe and economical operation of the boiler.

FOR ANY QUERIES PLEASE RING THE

IDEAL CONSUMER HELPLINE : 01482 498660

NOTE. BOILER RESET PROCEDURE -

To reset boiler, press button “r” on the control panel. The boiler will repeat the ignition sequence if a heat demand

is present

IMPORTANT NOTES

• This appliance must not be operated without the casing correctly tted and forming an adequate seal.

• If the boiler is installed in a compartment then the compartment MUST NOT be used for storage purposes.

• If it is known or suspected that a fault exists on the boiler then it MUST NOT BE USED until the fault has been corrected by

a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII).

•Under NO circumstances should any of the sealed components on this appliance be used incorrectly or tampered with.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

In cases of repeated or continuous shutdown a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII) should

be called to investigate and rectify the condition causing this and carry out an operational test. Only the manufacturers original

parts should be used for replacement.

MINIMUM CLEARANCES

Clearances of 165mm (6 1/2”) above, 100mm (4”) below, 2.5mm (1/8”) at the sides and 450mm (17 3/4”) at the front of the

boiler casing must be allowed for servicing.

Bottom clearance

Bottom clearance after installation can be reduced to 5mm.

This must be obtained with an easily removable panel to provide the 100mm clearance required for servicing.

A. Boiler Status

B. Exit Button

C. Down Button

D. Up Button

E. Enter Button

F. Reset Button

G. CH Temperature

Control

H. DHW

Temperature

Control and Off

Switch

J. Burner On

indication

K. Pressure Gauge

L. Boiler in Full

Condensing Mode

BOILER CONTROLS

LEGEND

1 3

ON ON

60°C

A J G

B C D

TO LIGHT THE BOILER. (REFER TO BOILER

CONTROLS)

If a programmer is tted refer to separate instructions for the

programmer before continuing.

1. Switch ON electricity to the boiler and check that all

external controls, e.g. programmer and room thermostat,

are ON.

2. Set the Domestic Hot Water temperature control (H) and

Central Heating temperature control (G) to ‘max’.

The boiler will commence the ignition sequence supplying heat

to the central heating, if required.

Note. In normal operation the boiler status display (A) will

display the boiler operation mode.

Boiler frost protection - boiler will re if temperature is less

than 5 degrees C.

During normal operation the burner on indicator (J) will remain

illuminated when the burner is lit.

If the boiler has not lit, after 5 ignition attempts, the following

screen will be displayed.

Ignition Lockout

Check other Gas Appliances work

If not, re-instate gas supply

Reset boiler by pressing r

If fault persists contact installer

Reset the boiler and the ignition sequence will be repeated.

OPERATION

CH and DHW required.

The boiler will re and supply heat to the radiators but will give

priority to DHW on demand.

If required the DHW preheat will operate as described on page

17 MENU OPERATION - Preheat, during periods when there

is no call for CH.

DHW only required.

Either set the heating control knob (G) to off - or,

Set the CH external controls to OFF.

Only if pre-heat is selected the boiler will re periodically for

a few seconds to maintain the DHW calorier in a pre-heated

condition. The average time period between firing is 90

minutes. This may vary considerably due to the surrounding

ambient temperature of the boiler.

The boiler will re whenever there is a demand for DHW.

The boiler preheat facility can be immobilised by selecting

preheat OFF (see page 17 MENU OPERATION - Preheat). This

will stop the boiler operating periodically for short periods. This

facility is primarily provided for boiler installations in a sensitive

area (i.e. bedroom etc.).

Note. If the pump and diverter valve have not operated in

the last 24 hours they will run briey to ensure they do not

become seized.

CONTROL OF WATER TEMPERATURE

Domestic Hot Water

The DHW temperature is limited by the boiler controls to

65oC maximum at low draw-off rate, adjustable via the DHW

temperature control (H).

Due to system variations and seasonal temperature uctuations

DHW ow rates/temperature rise will vary, requiring adjustment

at the draw off tap : the lower the rate the higher the

temperature, and vice versa.

Approx. hot water temperatures for the boiler thermostat

settings are:

Knob Setting Flow Temperature

Minimum 40ºC (104ºF)

Maximum 65ºC (149ºF)

Central Heating

The boiler controls the central heating radiator temperature

to a maximum of 80oC, adjustable via the CH temperature

control (G).

WEATHER COMPENSATION

When the Weather Compensation option is tted to the system

then the CH Temperature Control (G) becomes a method of

controlling room temperature. Turn the knob clockwise to

increase room temperature and anti-clockwise to decrease

room temperature. Once the desired setting has been

achieved, leave the knob in this position and the system will

automatically achieve the desired room temperature for all

outside weather conditions.

TO SHUT DOWN THE BOILER

Set the DHW temperature control knob to OFF.

TO RELIGHT THE BOILER

Repeat the procedure detailed in ‘To light the boiler’. Set the DHW temperature control knob to between min & max.

FROST PROTECTION

If no frost protection is provided and frost is likely during a short absence from home, leave the heating controls (if tted) at a

reduced temperature setting. For longer periods, the entire system should be drained.

If the system includes a frost thermostat then the timer can be left off (if tted). The mains supply should be left switched ON,

with the boiler thermostat left in the normal running position.

BOILER OVERHEAT PROTECTION

The boiler controls will shut down the boiler in the event of overheating. Should this occur, the following display will appear:

Overheat Lockout

Fill System to 1 Bar

Bleed Radiators, Rell System

Check Radiator Valves are Open

Reset Boiler by pressing r

LOSS OF SYSTEM WATER PRESSURE

The gauge (K ref page 6) indicates the central heating system

pressure. If the pressure is seen to fall below the original

installation pressure of 1-2 bar then conduct the re-pressurising

procedure as shown below. If unable to do so or if the pressure

continues to drop a Gas Safe Registered Engineer or in IE a

Registered Gas Installer (RGII) should be consulted.

THE BOILER WILL NOT OPERATE IF THE PRESSURE

HAS REDUCED TO LESS THAN 0.3 BAR UNDER THIS

CONDITION.

In this case the following display will appear:

To re-pressurise:

1. Ensure lling loop isolation valves are closed.

2. Remove the left hand caps.

3. Attach on the lling loop.

4. Turn the lling loop isolation valves to the open position.

The system will now ll.

5. Wait for pressure gauge to reach between1 to 2 bar.

6. Close the lling loop isolation valves.

7. Disconnect the lling loop at left hand side and angle

upwards.

8. Replace caps.

Closed

position

Open

position

Low Water Pressure

Fill System to 1 Bar

Bleed Radiators

Rell System to 1 Bar

Autres manuels pour Vogue Combi c26

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IDEAL Chaudière

IDEAL

IDEAL LOGIC HIU Direct MT Manuel utilisateur

IDEAL

IDEAL MINI C24 Manuel utilisateur

IDEAL

IDEAL LOGIC+ Combi 24 Manuel utilisateur

IDEAL

IDEAL Optia FF 30 Note de version

IDEAL

IDEAL Concord CXS 40 Guide de l'utilisateur

IDEAL

IDEAL EVOMAX 2 Series Manuel utilisateur

IDEAL

IDEAL icos M3080 Manuel utilisateur

IDEAL

IDEAL classic HE15P Guide de l'utilisateur

IDEAL

IDEAL c80 ff Manuel utilisateur

IDEAL

IDEAL Concord CXA 40 Manuel utilisateur

IDEAL

IDEAL Henrad SE 30 FF Manuel utilisateur

IDEAL

IDEAL EVO S 50 Manuel utilisateur

IDEAL

IDEAL Concord CXSi 120/H Fiche technique

IDEAL

IDEAL Henrad SEC 80FF Guide de l'utilisateur

IDEAL

IDEAL imax W60 Manuel utilisateur

IDEAL

IDEAL LOGIC CODE COMBI ESP1 33 Manuel utilisateur

IDEAL

IDEAL MINI C24 Manuel utilisateur

IDEAL

IDEAL Classic SE9 FF Guide de l'utilisateur

IDEAL

IDEAL istor HE325 Manuel utilisateur

IDEAL

IDEAL Classic LX RS 230 Note de version

IDEAL

IDEAL INSTINCT 24 Manuel utilisateur

IDEAL

IDEAL classic HE15P Manuel utilisateur

IDEAL

IDEAL Classic SE9 RS Manuel utilisateur

IDEAL

IDEAL Mexico Super FF440 Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur