ID Lock FW 1.6 Manuel utilisateur

Z-Wave Module

Technical manual

for FW 1.6

ENGLISH

______________

V3.02 EN 19-08-09

 ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019 
idlock.no 
 
 
idlock.no/zwave 
ID Lock 

 
Table of Contents 
 
Introduction ................................................................................................................... 3 
Overview....................................................................................................................... 3 
Getting started .............................................................................................................. 4 
1. Identify your model type (101 or 150)................................................................... 4 
2. ID Lock 101.......................................................................................................... 5 
Inclusion and Exclusion (Adding or removing) ............................................................ 5 
Z-Wave module device reset ...................................................................................... 5 
3. ID Lock 150.......................................................................................................... 6 
Inclusion and Exclusion (Adding or removing) ............................................................ 6 
Z-Wave module device reset ...................................................................................... 6 
Z-Wave firmware version .............................................................................................. 7 
1. Firmware version 1.6............................................................................................ 7 
Z-Wave Specifications .................................................................................................. 7 
1. Supported Command Classes.............................................................................. 8 
Configuration Parameters ............................................................................................. 9 
Notification Parameter................................................................................................. 12 
1. Use Case of Manual Lock Notification................................................................ 14 
2. Use Case of Manual Unlock Notification ............................................................ 14 
3. Use Case of RF Lock Operation......................................................................... 14 
4. Use Case of RF Unlock Operation ..................................................................... 15 
5. Use Case of Keypad Lock Operation ................................................................. 15 
6. Use case of Keypad Unlock Operation............................................................... 15 
7. Use case of Auto lock locked operation.............................................................. 15 
8. Use case of Lock Jammed ................................................................................. 16 
9. Use case of All User Code Deleted .................................................................... 16 

 ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019 
idlock.no 
 
 
idlock.no/zwave 
ID Lock 

10. Use case of Single User Code Deleted ............................................................ 16 
11. Use case of New User Code Added................................................................. 16 
12. Use case of User Code Not Added Due to Duplicate Code .............................. 17 
13. Use case of Unlock by RF with invalid user code ............................................. 17 
14. Use case of lock by RF with invalid user code.................................................. 18 
15. Use case of Tampering (Door Forced Open).................................................... 18 
16. Use case of Emergency (Fire Sensor).............................................................. 18 
Manufacturer Parameter ............................................................................................. 19 
Version Parameter ...................................................................................................... 20 
User Codes (PINs and RFIDs) .................................................................................. 20 
1. User code ID status.......................................................................................... 20 
2. Credentials....................................................................................................... 21 
Door Lock Operation Report Value............................................................................ 22 
Battery Level Report.................................................................................................. 22 
Association & Association Group Parameter ............................................................. 23 
Glossary.................................................................................................................... 23 
 
 

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

1. Introduction

The ID Lock Z-Wave Module is a security enabled Z-Wave Plus product which is able

to use encrypted Z-Wave Plus messages in order to communicate to other Z-Wave

Plus products with enabled security.

The module is created for the ID Lock 150 and is also backwards compatible with the

ID Lock 101 (note that some functionallity is not available on ID Lock 101).

The ID Lock Z-Wave Module must be used in conjunctioin with a Security Enabled

Z-Wave Controller in order to fully utilize its full capability. Other nodes in the Z-

Wave network can function as repeaters.

The ID Lock Z-Wave Module can be included and operated in any Z-Wave network

containing other certified Z-Wave products regardless of manufacturer.

Using the Z-Wave Module on the ID Lock will affect the battery life of the door lock.

The ID Lock Z-Wave Module does not support the Basic Set Command Class.

2. Overview

Z-Wave Module is a Z-Wave interface device of ID Lock and is used to connect a to Z-

Wave Controller using the Z-Wave protocol.

This document decribes the spesifics for Z-Wave command classes used when ID

Lock Z-Wave Module is interfacing with a Z-Wave controller.

Front Side of Z-Wave Module

Back Side of Z-Wave Module Sales box and Z-Wave module

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

3. Getting started

3.1. Identify your model type (101 or 150)

The keypads on 101 and 150 are different. Whilst the 101 has a * (star) and # (hash)

left and right of digit “0” the 150 has open and closed padlocks (see pictures below).

Note: FW v1.6 of ID Lock Z-Wave Module has reduced compatibility for ID Lock 101.

The Z-Wave Module fits only one way below

the batteries on both 101 and 150. The slot

is marked “Remote control”.

IMPORTANT!

Always remove batteries before inserting or

removing the Z-Wave Module.

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

3.2. ID Lock 101

3.2.1. Inclusion and Exclusion (Adding or removing)

For inclusion (puts your device in inclusion mode) of ID Lock 101 first set your

designated Z-Wave controller in inclusion mode then press and hold the

Key Button [A] until keypad is activated whilst the door lock is open and unlocked.

Release button [A] and press digit [8] on keypad.

Inclusion mode starts immediately and is indicated by flashing blue LEDs.

3.2.2. Z-Wave module device reset

For Z-Wave local reset follow same procedure except use digit [0].

Reset starts immediately and is indicated by flashing blue LEDs.

Warning!

After Z-Wave local reset the device might have to be excluded before a new inclusion.

This function is made available by design only to be used if your module

does no longer function properly or if your Z-Wave controller is lost.

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

3.3. ID Lock 150

3.3.1. Inclusion and Exclusion (Adding or removing)

For inclusion (puts your device in inclusion mode) of ID Lock 150 first set your

designated Z-Wave controller in inclusion mode then press and hold the

Key Button [A] until keypad is activated whilst the door lock is open and unlocked.

1. Release button [A] and enter Master PIN [1234], followed by [*] on keypad.

2. Press digit [2], followed by [*] to enter settings menu.

3. Press digit [5] to start inclusion or exclusion.

Inclusion/exclusion mode starts immediately and is indicated by flashing blue LEDs.

3.3.2. Z-Wave module device reset

For Z-Wave local reset follow same procedure except use digit [0] instead of [5].

Take notice that if the Z-Wave module is included in a Z-Wave network the door lock

will return to factory settings when performing a local reset.

Reset starts immediately and is indicated by flashing blue LEDs.

Warning!

After Z-Wave local reset the device might have to be excluded before a new inclusion.

This function is made available by design only to be used if your module

does no longer function properly or if your Z-Wave controller is lost.

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

4. Z-Wave firmware version

This chapter contains the release for the Z-Wave Module firmware.

ID Lock 150 firmware can and must be updated with the app ID Lock 150 Updater

which is available for iOS and Android devices (idlock.no/updater).

4.1. Firmware version 1.6

Firmware version 1.6 is compatible with ID Lock 150 firmware 1.4.7 and newer.

•Configuration parameters

oChanged how ID lock 150 handles configuration parameter 2 “RFID

Registration mode”.

oAdded configuration report for Door audio volume (configuration parameter

4) and service pin mode (configuration parameter 7)

oAdded values 0x07 “always mode” and 0xFE “disable mode” to configuration

parameter 7 service pin mode.

oChanged configuration parameter 8 “updater mode” and 9 “Master pin

mode”.

•Notification parameters

oAdded serveral new notification events for “Access Control” (0x06).

Notifications for different lock types, add and delet credensials and lock

jammed alarm added.

oMoved remote unlock from “keypad unlock operation” with identifier 0x00, to

“RF unlock operation” with identifier 0x00.

•Version parameter

oChanged how a version report descibes ID lock 150 firmware version.

•Credensials of Z-Wave index

oChanged Z-Wave identifiers for master PIN, service PIN, user PINs and RFID.

•Battery

oBugfixes related to CC battery.

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

5. Z-Wave Specifications

○Device Type: Secure Keypad Door Lock

○Role Type: LSS (Listening Sleeping Slave)

5.1. Supported Command Classes

◼Non Secure Mode

CLASS

Value (Hex)

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_SECURITY_V1

COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1

COMMAND_CLASS_POWERLEVEL_V1

COMMAND_CLASS_CONFIGURATION_V1

◼Secure Mode (S0)

CLASS

Define Value (Hex)

COMMAND_CLASS_VERSION_V2

COMMAND_CLASS_DOOR_LOCK_V2

COMMAND_CLASS_USER_CODE_V1

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1

COMMAND_CLASS_NOTIFICATION_V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

COMMAND_CLASS_BATTERY_V1

ID Lock Z-Wave Module Technical manual for FW 1.6 June 20th 2019

idlock.no

idlock.no/zwave

ID Lock

6. Configuration Parameters

These configuration parameter numbers and values are specific for the different

applications.

COMMAND_CLASS_CONFIGURATION

Name

Parameter

Number

Size

Parameter

Values

Description

Configuration

Set parameter

0-3

Door Lock Mode

5,9

RFID Mode (only IDL-150)

0-1

Door Hinge Position Mode

0-5

Audio Volume

0-1

Door Relock Mode

0-9, FE

Service Pin Mode

150

Door Lock Model Type

(read only, only IDL-150)

0-3

Updater Mode (only IDL-150)

0-1

Master PIN Mode

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ID Lock Unité de contrôle

ID Lock

ID Lock 202 MULTI Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur