ICP DAS USA M-7067 Manuel utilisateur

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7067

7 Channel Form A Relay Output Digital Input

Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7067_m_7067d.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7067 device is a network data acquisition and control module that

support Modbus RTU. They can be remotely controlled using a set of

commands called DCON protocol. With the Modbus RTU protocol, it can

easily communicate with most popular SCADA/ HMI software and PLCs.

2. Terminal Assignment

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA I-8123W Guide de configuration

ICP DAS USA

ICP DAS USA IR-310-RM Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8213W-4G Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7000 series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8014W Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7218Z Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7019Z Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7041D Manuel utilisateur

ICP DAS USA

ICP DAS USA DS-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7080 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7088 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7033D Manuel utilisateur

ICP DAS USA

ICP DAS USA IR-712A Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA tSG-3781B Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7H16M Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA tZT-P4C4 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7060D Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA GT-540P-3GWA-OEM1 Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-714i Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7188XA Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-2017 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur