Icom iF3200DEX series Manuel utilisateur
OPERATING INSTRUCTIONS
iF3200DEX
series
5 SPEAKER MICROPHONE
4 NXDN™OPERATION
3 BASIC OPERATION
2 PANEL DESCRIPTION
1 ACCESSORIES
INTRODUCTION
VHF DIGITAL/ANALOG TRANSCEIVERS
iF4200DEX
series
UHF DIGITAL/ANALOG TRANSCEIVERS
(Limited functions only)
i
INTRODUCTION
FOREWORD
Thank you for choosing this Icom product.
The IDAS™NXDN™system operation is built into your
transceiver.
IMPORTANT
FIRST, CAREFULLY READ INSTRUCTIONS
qPRECAUTIONS and wINSTRUCTIONS that are
provided with the transceiver.
SAVE THIS OPERATING GUIDE— This op-
erating guide contains additional important operating
instructions for the IC-F3201DEX, IC-F3202DEX and
IC-F3203DEX v h f digital/a n a l o g t r a n s c e i v e r s and
the IC-F4201DEX, IC-F4202DEX and IC-F4203DEX
u h f digital/a n a l o g t r a n s c e i v e r s .
NOTE
To use in explosive environments, read the “SAFETY
MANUAL” leaflet that comes with the transceiver.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia and/
or other countries.
IDAS is trademark of Icom Incorporated (Japan).
NXDN is a trademark of Icom Incorporated and Kenwood
Corporation.
All other products or brands are registered trademarks or
trademarks of their respective holders.
1-1
Section 1ACCESSORIES
Supplied accessories..............................................................1-2
Attaching accessories ............................................................1-3
Flexible antennaD......................................................................1-3
Battery packD............................................................................1-3
Belt clipD....................................................................................1-4
Connector coverD......................................................................1-4
1ACCESSORIES
1-2
Supplied accessories
The following accessories are supplied.
Battery pack*
Belt clip* Connector cover
(with screw)
Battery charger* Power adapter*
* Not supplied, or the shape is different, depending on the transceiver’s version.
Flexible antenna
(This illustration is for the VHF type.)
1ACCESSORIES
1-3
Attaching accessories
Flexible antennaD
Connect the supplied flexible antenna to the antenna
connector.
CAUTION:
• NEVER carry the transceiver by holding only the
antenna.
• DO NOT connect any antenna other than those
listed in the basic instructions.
• Transmitting without an antenna will damage the
transceiver.
Battery packD
To attach the battery pack:
Slide the battery pack on the back of the transceiver in the
direction of the arrow (q)
until the battery release button
makes a ‘click’ sound.
To remove the battery pack:
Slide
the battery release button in the direction of the
arrow (w), as shown to the right. The battery pack is
then released, and you can remove it.
NEVER remove or attach the battery pack when the
transceiver is wet or soiled. This may result in water
or dust getting into the transceiver/battery pack and
may damage them.
NOTE: Keep the battery pack terminals clean. It’s a
good idea to occasionally clean them.
q
w
Battery release
button
1ACCESSORIES
1-4
Belt clipD
Before attaching or detaching the belt clip, remove the
battery pack if it is attached.
To attach the belt clip:
Slide the belt clip in the direction of the arrow until it➥
locks and makes a ‘click’ sound.
To detach the belt clip:
Lift the tab up (➥q), and slide the belt clip in the direc-
tion of the arrow (w).
Attaching accessories (Continued)
Connector coverD
To attach the connector cover:
Place the connector cover over the multi-connector.q
(q)
Tighten the screw. (ww)
To detach the connector cover:
Remove the screw using a Phillips screwdriver. (qe)
Detach the connector cover to connect optionalw
equipment. (r)
Belt clip
w
q
Ta b
r
e
q
w
CAUTION:
Attach the connector cover when the optional ac-
cessory is not used. Otherwise, the terminals of the
multi-connector may be shorted, and this could dam-
age the transceiver.
2PANEL DESCRIPTION
2-2
Front, top and side panels
qROTARY SELECTOR
Rotate to select the preprogrammed memory chan-
nels or scan lists, depending on the presetting.
wVOLUME CONTROL [VOL]
Rotate to turn the power ON or OFF, and adjust the
audio level.
eSTATUS INDICATOR (p. 2-3)
Lights red while transmitting.➥
Lights green while receiving a signal, or when the➥
squelch is open.
Lights/blinks orange when a matched 2/5-Tone➥
code is received, depending on the presetting.
rMULTI CONNECTOR
Connect an optional accessory.
CAUTION:
Attach the connector cover
when an optional accessory
is not used. Otherwise, the
terminals of the multi-con-
nector may be shorted, and
this could damage the trans-
ceiver.
tPTT SWITCH [PTT]
Hold down to transmit, release to receive.
yLOWER KEY [Lower]
uUPPER KEY [Upper]
A desired functions can be preset. (p. 2-4)
iEMERGENCY KEY [Emer]
A desired functions can be preset. (p. 2-4)
oANTENNA CONNECTOR
Connect the antenna.
Connector
cover
Microphone
Speaker
wVOLUME
CONTROL
eSTATUS INDICATOR
yLOWER KEY
uUPPER KEY
qROTARY
SELECTOR
oANTENNA
CONNECTOR
rMULTI
CONNECTOR
tPTT SWITCH
iEMERGENCY
KEY
2PANEL DESCRIPTION
2-3
Status indicator
• TX:
Lights Red while transmitting.
• RX busy:
On an analog channel, lights Green when the noise
squelch opens. On a digital or mixed channel, lights
Green while detecting a frame synchronization.
• Call LED:
Turns ON or blinks* when receiving a matched 2/5-
Tone, or a Call Alert.
*Depending on the presetting.
• Fast or Slow scan:
Blinks when scanning for a channel to search for a
signal.
• Low Battery 1:
You should charge the battery soon. (blinks slowly)
• Low Battery 2:
You must charge the battery. (blinks fast)
• TX low Battery 1:
Low Battery was detected in the TX mode.
• TX low Battery 2:
Very Low Battery was detected
in the
TX mode.
• Channel Error:
Continuously blinks when a non-programmed chan-
nel is selected.
• Power ON:
Blinks at transceiver startup.
R
G
O
O O
G G
G G
G G G G
The status indicator indicates the various parameters
of the transceiver as described below.
(Reference: R is Red, G is Green, O is Orange)
R O R O R O R O R O R O R O R O
R O GRO G
R R
R R R R
(When turns ON)
(When blinks)
2PANEL DESCRIPTION
2-4
Programmable function keys
The following functions can be assigned to the [Upper],
[Lower] and [Emer] programmable function keys.
LOWER KEY
UPPER KEY
EMERGENCY
KEY
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Icom Émetteur-récepteur
Icom
Icom IC-F3161 Series Manuel utilisateur
Icom
Icom IC-F43GT Manuel utilisateur
Icom
Icom IC-7400 Manuel utilisateur
Icom
Icom IC-V8 Manuel utilisateur
Icom
Icom IC-9100 Guide d'installation
Icom
Icom IC-229A Manuel utilisateur
Icom
Icom IC-V100 Manuel utilisateur
Icom
Icom IC-F310S Manuel utilisateur
Icom
Icom IC-M505 Manuel utilisateur
Icom
Icom IC-4088A Manuel utilisateur
Icom
Icom IC-F25SR Manuel utilisateur
Icom
Icom D-STAR ID-4100A Manuel utilisateur
Icom
Icom IC-7600 Manuel utilisateur
Icom
Icom IC-F3162DT Manuel utilisateur
Icom
Icom IC-F5061 Manuel utilisateur
Icom
Icom IC-28A Manuel utilisateur
Icom
Icom IC-91A Manuel utilisateur
Icom
Icom IC-4088SR Manuel utilisateur
Icom
Icom IC-M5 Manuel utilisateur
Icom
Icom IC-725 Manuel utilisateur
