Icom IC-V86 Guide de configuration

13 OPTIONS

12 TROUBLESHOOTING

11 RESETTING

10 PROGRAMMING

9 SET MODES

8 DTMF MEMORY

TONE SQUELCH AND POCKET BEEP

6 SCAN OPERATION

5 MEMORY/CALL OPERATION

REPEATER AND DUPLEX OPERATION

3 ADVANCED OPERATION

2 BATTERY CHARGE

1 ACCESSORIES

INTRODUCTION

ADVANCED MANUAL

VHF TRANSCEIVER

|V86

INTRODUCTION

Thank you for choosing this Icom product. This

product was designed and built with Icom’ s state of

the art technology and craftsmanship. With proper

care, this product should provide you with years of

trouble-free operation.

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains advanced operating

instructions for the IC-V86. For basic operating

instructions, see the BASIC MANUAL.

FEATURES

zRugged construction (IP54* and MIL-STD-810G)

zPowerful 7.0 W of output power (Extra High power)

zExtend Battery Life function (With the BC-240)

* Only when the battery pack or case, antenna, and jack

cover are attached.

Icom, Icom Inc. and the Icom logo are registered

trademarks of Icom Incorporated (Japan) in Japan,

the United States, the United Kingdom, Germany,

France, Spain, Russia, and/or other countries.

All other products or brands are registered trademarks

or trademarks of their respective holders.

Icom is not responsible for the destruction, damage

to, or performance of any Icom or non-Icom

equipment, if the malfunction is because of:

• Forcemajeure,including,butnotlimitedto,res,

earthquakes,storms,oods,lightning,other

natural disasters, disturbances, riots, war, or

radioactive contamination.

•The use of Icom transceivers with any equipment

that is not manufactured or approved by Icom.

1-1

Section 1ACCESSORIES

Supplied Accessories .............................................................................1-2

Antenna ..................................................................................................1-2

Belt clip...................................................................................................1-2

Battery pack or case...............................................................................1-3

Jack cover ..............................................................................................1-3

1ACCESSORIES

1-2

Supplied Accessories

Battery pack*

Jack cover

(with screws)

Battery charger*

Belt clip

Power adapter*

Antenna*

* Not supplied, or the shape is different, depending on

the transceiver version.

Antenna

Insert the antenna into the antenna connector and

twist the antenna base to lock it in place.

CAUTION:

•NEVER HOLD just the antenna when carrying the

transceiver.

•DO NOT transmit without an antenna.

Belt clip

To attach the belt clip:

zSlide the belt clip in the direction of the arrow until

the belt clip locks in place, and makes a ‘click’

sound.

Belt clip

Battery pack/case

To detach the belt clip:

1. Remove the battery pack or case from the

transceiver, if it is attached.

2. Lift the tab up (1), and slide the belt clip in the

direction of the arrow (2).



1ACCESSORIES

1-3

Battery pack or case

CAUTION: When the battery case is attached, the

Battery Protection function must be turned OFF in

the Initial Set mode. (p. 9-7)

To attach the battery pack or case:

1. Insert the battery pack or case in the direction of

the arrow (1), then close.

2. Hook the latch until it makes a ‘click’ sound (2).



Battery pack/case

Latch

To remove the battery pack or case:

RWARNING! The latch is tightly locked, so use

caution when releasing it. DO NOT use your

ngernail.Usetheedgeofacoinorscrewdrivertip

to carefully release it.

zUnhook the latch (1), and then lift up the battery

pack or case in the direction of the arrow (2).





CAUTION: NEVER remove or attach the battery

pack or case when the transceiver is wet or soiled.

This may result in water or dust getting into the

transceiver or the battery pack or case, and may

result in them being damaged.

NOTE: Keep battery terminals clean. It’s a good idea

to occasionally clean them.

Jack cover

Attach the jack cover when optional equipment is not

used.

To attach the jack cover

1. Attach the jack cover

to the [SP MIC] jack

(1).

2. Insert and tighten the

screws (2).

To detach the jack cover

1. Remove the screws

with a phillips

screwdriver (1).

2. Detach the jack cover

to connect optional

equipment (2).





2-1

Section

Battery chargers .....................................................................................2-2

DUsing the BC-191 to rapid charge the BP-264 ...............................2-2

DUsing the BC-192 to regular charge the BP-264 ............................2-2

DUsing the BC-240 to rapid charge the BP-298/BP-299 ..................2-3

Optional battery case (BP-263) ..............................................................2-4

2BATTERY CHARGE

2-2

DUsing the BC-191 to rapid charge

the BP-264

The BC-191 provides rapid charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time: Approximately 2 hours

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable.

DUsing the BC-192 to regular charge

the BP-264

The BC-192 provides regular charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time: Approximately 16 hours

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L DC power cable.

The optional OPC-

515L (for a DC power

source) or CP-23L

(for a 12 V cigarette

lighter socket) can be

used instead of the

power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Using screws are

recommended to

secure the charger.

Charging indicator

•Lights orange: While charging

•Lights green: When charging is completed.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Battery pack + Transceiver

Turn OFF

Battery pack

The optional OPC-515L

(for a DC power source)

can be used instead of

the power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Battery pack + Transceiver

Battery pack

Turn OFF

Using screws are

recommended to

secure the charger.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Charging indicator

•Lights green while charging.

NOTE:

The charge indicator will not go

out even after a battery pack is

fully charged.

Charging time period differs,

depending on the input voltage.

12 V: Approximately 36 hours

13.8 V: Approximately 21 hours

16 V: Approximately 16 hours

Battery chargers

2BATTERY CHARGE

2-3

DUsing the BC-240 to rapid charge

the BP-298/BP-299

The BC-240 provides rapid charging of only the

BP-298/BC-299 Li-ion battery pack. Never use it to

charge any other battery pack.

Charging time*

with the BP-298: Approximately 3 hours

with the BP-299: Approximately 4.6 hours

* When the Extend Battery Life function is turned OFF.

See the BASIC MANUAL for details.

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable.

CAUTION: When using the OPC-515L DC power

cable NEVER connect the OPC-515L to a power

source using reverse polarity. This will ruin the

battery charger. White line:

Black line:

–

The optional OPC-515L

(for a DC power source)

or CP-23L (for a 12 V

cigarette lighter socket)

can be used instead of

the power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Battery pack + Transceiver

Battery pack

Turn OFF

Using screws are

recommended to

secure the charger.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Charging indicator

•Lights orange: While charging

•Lights green: When charging is completed.

•Blinks red: When a charging error has

occurred.

Battery chargers

2BATTERY CHARGE

2-4

Optional battery case (BP-263)

When using the battery case (BP-263), install 6 × AA

(LR6) size alkaline batteries, as described below.

Remove the battery case, if it is attached. (p. 1-3)

Install 6 × AA (LR6) size alkaline batteries.

Install only alkaline batteries.

Be sure to observe the correct polarity.

Attach the battery case. (p. 1-3)

CAUTION:

•When installing batteries, make sure they are all

the same brand, type and capacity. Also, do not

mix new and old batteries together.

•Keep battery terminals clean. It’s a good idea to

occasionally clean them.

•Never incinerate used battery cells since the

internal battery gas may cause them to rupture.

•Never expose a detached battery case to water.

If the battery case gets wet, be sure to wipe it dry

before using it.

•Never use batteries whose insulated covering is

damaged.

BE CAREFUL! The negative

terminals of the battery case

protrude from the body, so

pay attention not to injure your

ngerswheninsertingthe

batteries.

3-1

Section

Adjusting the audio level.........................................................................3-2

Selecting passband width.......................................................................3-2

Receiving................................................................................................3-2

Transmitting............................................................................................3-2

[VOL] function assignment .....................................................................3-3

Weather channel operation (For only the USA version) .........................3-4

DWeather channel selection..............................................................3-4

DWeather Alert function.....................................................................3-4

3ADVANCED OPERATION

Table des matières

Autres manuels Icom Émetteur-récepteur

Icom

Icom IC-F3210D Series Manuel utilisateur

Icom

Icom IC-28H Manuel utilisateur

Icom

Icom IC-F3001 Manuel utilisateur

Icom

Icom IC-F3262DT Manuel utilisateur

Icom

Icom IC-A23 Manuel utilisateur

Icom

Icom IC-2820H Instructions de montage

Icom

Icom IC-705 Manuel utilisateur

Icom

Icom IC-281A Manuel utilisateur

Icom

Icom iM504 Manuel utilisateur

Icom

Icom ic-2730A Manuel du propriétaire

Icom

Icom IC-SAT100 Manuel utilisateur

Icom

Icom IC-V210T Manuel du propriétaire

Icom

Icom IC-290H/D Manuel utilisateur

Icom

Icom iC-7850 Manuel utilisateur

Icom

Icom IC-756 Manuel utilisateur

Icom

Icom IC-U8S1 Manuel utilisateur

Icom

Icom ID-1 Manuel utilisateur

Icom

Icom IC-756PRO2 Manuel utilisateur

Icom

Icom IC-V8 Manuel utilisateur

Icom

Icom IC-E90 Manuel utilisateur

Icom

Icom iF3002 Manuel utilisateur

Icom

Icom IC-M801GMDSS Manuel utilisateur

Icom

Icom IC-4088A Mode d’emploi

Icom

Icom IC-703 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur