Icom IC-F8100 Manuel utilisateur

Page: 1/ 3

Confidential

Icom IC-F8100 Antenna Tuner Control Protocol

Date: Aug 23rd, 2011

1. Pin Configuration

For AT-140/AT-130 (Icom’s auto-antenna tuner)

AD-119 GPIO / OPC-2205 ANT Tuner 側

No. Name Function @using AT-140 Operation

1 13.8 13.8 V output for Antenna

tuner

3 KEY Key signal input –0.5 to 0.8 V during tuning

11 START Start/through signal output

14 GND Connect to ground

Chart-1: Wiring Information

2. Control Method

Tuning operation works as below. (See Chart-2: Timing Chart)

1. Push and hold [TUNER(9)] keypad.

2. ”START” line turns from “H” to “L” for 500ms.

3. After approx. 300ms passed from “START” turned to “L”, AT-140 turns “KEY” line to “L”.

(Tuning operation start)

4. When “KEY” line turned to “L”, F8100 transmits a 10W signal on CW mode.

5. ”KEY” line turned “H” for 200ms after 20ms from the tuning operation has done, F8100

interprets that the tuning operation succeeded then “T” icon shows up on F8100 display. On

the other hand, “KEY” line turned “L” for 200ms after 20ms from the turning operation has

done, F8100 interprets that the tuning operation failed.

Page: 2/ 3

Push [TUNER] keypad

500mS

START

300mS 20mS 200mS

KEY

Tuning Starts Tuning Done

TX 10W (CW)

Chart-2: Timing Chart of Tuning Operation

*Using “Tuner Through”function

1. Push [TUNER(9)] keypad while “T”icon is shown on F8100 display. When “Tuner

Through”function activates, “T”icon disappears from F8100 display.

2. “START” line turns from “H” to “L” for 70ms.

70mS

START

KEY

“KEY” line stays “H”, no answer back is initiated.

Chart-3: Timing Chart of Tuner Through Operation

OUTPUT(Tx)

OFF

Page: 3/ 3

3. Control Signal Level

[START]

Voltage [V]

Chart-4: Signal Level of START line

[KEY]

Voltage [V]

Chart-5: Signal Level of KEY line

AT-140 Pin Configuration

More than 350 ms*

Less than 1V to start tuning

*For “Tuner Through” function ;Less than 250 ms

Approximately 5V

Automatic Tuning Process

Grounded

Approx. 5V

Time

Autres manuels pour IC-F8100

Table des matières

Autres manuels Icom Émetteur-récepteur

Icom

Icom IC-A22 Manuel utilisateur

Icom

Icom IC-7100 Manuel utilisateur

Icom

Icom IC-7200 Manuel utilisateur

Icom

Icom IC-F3230D Manuel utilisateur

Icom

Icom IC-F1100D Series Manuel utilisateur

Icom

Icom IC-M502 Manuel utilisateur

Icom

Icom IC-A16E Guide d'installation

Icom

Icom IC-M710 Manuel utilisateur

Icom

Icom IC-7800 Manuel utilisateur

Icom

Icom IC-228A Manuel utilisateur

Icom

Icom IC-F3360D Series Manuel utilisateur

Icom

Icom IC-215 Manuel utilisateur

Icom

Icom IC-M802 Manuel utilisateur

Icom

Icom IC-T90 Manuel utilisateur

Icom

Icom IC-3210A Manuel utilisateur

Icom

Icom IC-F3 Manuel utilisateur

Icom

Icom iF5061 Manuel utilisateur

Icom

Icom IC-F5061 Manuel utilisateur

Icom

Icom IC-F52D Manuel utilisateur

Icom

Icom IC-M36 Manuel utilisateur

Icom

Icom IC-M602 Manuel utilisateur

Icom

Icom IC-4008A Manuel utilisateur

Icom

Icom IC-M502A Manuel utilisateur

Icom

Icom IC-2A Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur