Icom IC-E90 Manuel utilisateur
MULTIBAND FM TRANSCEIVER
ie90
INTRODUCTION
This service manual describes the latest service information for
the IC-E90 MULTIBAND FM TRANSCEIVER at the time of
publication.
E90
MODEL VERSION SYMBOL
Europe
Europe-1
United Kingdom
Italy
Spain
France
EUR
EUR-1
UK
ITR
ESP
FRA
To upgrade quality, all electrical or mechanical parts and inter-
nal circuits are subject to change without notice or obligation.
DANGER
NEVER connect the transceiver to an AC outlet or to a DC
power supply that uses more than 12 V. Such a connection
could cause a fire hazard and/or electric.
DO NOT expose the transceiver to rain, snow or any liquids.
DO NOT reverse the polarities of the power supply when
connecting the tranceiver.
DO NOT apply an RF signal of more than 20 dBm (100 mW)
to the antenna connector. This could damage the transceiver s
front end.
ORDERING PARTS
Be sure to include the following four points when ordering
replacement parts:
1. 10-digit order numbers
2. Component part number and name
3. Equipment model name and unit name
4. Quantity required
<SAMPLE ORDER>
1130006220 S.IC TC4W53FU IC-E90 LOGIC UNIT 1 piece
8930054290 2372 Main seal IC-E90 Chassis 5 pieces
Addresses are provided on the inside back cover for your
convenience.
REPAIR NOTES
1. Make sure a problem is internal before disassembling the transceiver.
2. DO NOT open the transceiver until the transceiver is disconnected from its power source.
3. DO NOT force any of the variable components. Turn them slowly and smoothly.
4. DO NOT short any circuits or electronic parts. An insulated tuning tool MUST be used for all adjustments.
5. DO NOT keep power ON for a long time when the transceiver is defective.
6. DO NOT transmit power into a signal generator or a sweep generator.
7. ALWAYS connect a 40 dB or 50 dB attenuator between the transceiver and a deviation meter or spectrum analyser when
using such test equipment.
8. READ the instructions of test equipment thoroughly before connecting equipment to the transceiver.
TABLE OF CONTENTS
SECTION 1 SPECIFICATIONS
SECTION 2 INSIDE VIEWS
SECTION 3 DISASSEMBLY INSTRUCTIONS
SECTION 4 CIRCUIT DESCRIPTION
4 - 1 RECEIVER CIRCUITS ................................................................................................... 4 - 1
4 - 2 TRANSMITTER CIRCUITS ............................................................................................ 4 - 4
4 - 3 PLL CIRCUITS................................................................................................................. 4 - 5
4 - 4 POWER SUPPLY CIRCUITS.......................................................................................... 4 - 7
4 - 5 PORT ALLOCATIONS..................................................................................................... 4 - 7
SECTION 5 ADJUSTMENT PROCEDURES
5 - 1 PREPARATION................................................................................................................ 5 - 1
5 - 2 TRIMMER ADJUSTMENT............................................................................................... 5 - 3
5 - 3 ADJUSTMENT MODE ADJUSTMENTS ......................................................................... 5 - 5
SECTION 6 PARTS LIST
SECTION 7 MECHANICAL PARTS AND DISASSEMBLY
SECTION 8 SEMI-CONDUCTOR INFORMATION
SECTION 9 BOARD LAYOUTS
9 - 1 LOGIC UNIT .................................................................................................................... 9 - 1
9 - 2 RF UNIT........................................................................................................................... 9 - 3
9 - 3 AF UNIT / VCO UNIT ...................................................................................................... 9 - 5
SECTION 10 BLOCK DIAGRAM
SECTION 11 VOLTAGE DIAGRAM
1 - 1
MGENERAL
• Frequency range : (Unit: MHz)
• Mode : FM, AM (RX only) and WFM (Rx only)
• Number of memory channels : 555 (incl. 50 scan edges and 5 call channels)
• Frequency stability : ±6 ppm max. (–10˚C to +60˚C; 14˚F to 140˚F)
• Tuning steps : 5, 6.25, 8.33, 9, 10, 12.5, 15, 20, 25, 30, 50 100, and 200 kHz
• Usable tempareture range : –10˚C to +60˚C; 14˚F to 140˚F
• Power supply requirement : 5.5 – 11 V DC or specified battery pack
• Usable battery pack/case : BP-217 (7.4 V) and BP-216 (3.2 V)
• Polarity : Negative ground
• Current drain (at 8.0 V DC) : (typical value)
*1Power save duty is 1:4.
• Anntena connector : SMA (50 Ω)
• Dimensions
(projections not included)
: 58(W) ×87(H) ×29(D) mm;
217⁄32(W) × 37⁄16(H) × 15⁄32(D) in
• Weight (with BP-217/Ant.) : 280 g; 9
7⁄8
oz
MTRANSMITTER
• Output power (at 8.0 V DC) : High 5.0 W typical
Low 0.5 W typical
• Modulation system :
Variable reactance modulation
• Max. freq. deviation : ±5 kHz
• Spurious Emissions : Less than –60 dB
• External MIC connector : 3-conductor 2.5(d) mm (1⁄8”); 2 kΩ
SECTION 1 SPECIFICATIONS
440 MHz
2.0 A
1.2 A
RX
High power
Low power
Rated output
Standby
Power saved*1
50/145 MHz
2.0 A
0.8 A 220 mA
100 mA
65 mA
Version
EUR
UK
ITR
ESP
EUR-1
FRA
50 MHz
50 – 52
50 – 51
–
50.2 – 51.2
145 MHz
144 – 148
440 MHz
430 – 440
430 – 434
435 – 438
430 – 440
Receiving
0.495–999.990
50.000–52.000, 144.000–146.000, 430.000–440.000
0.495–29.995, 50.000–52.000, 76.000–135.995,
144.000–146.000, 430.000–440.000
TX
2 - 1
SECTION 2 INSIDE VIEWS
EEPROM
(IC2: HN58X24128FPI,
Q2: UN9115)
RESET IC
(IC142: S-80928CNMC) Crystal oscillator for CPU clock
(X1: CR-687, 6.7584 MHz, Q40:UN9215)
CPU
(IC1: M30220MA-114RP)
AF regulator
(Q201: 2SB1201,
Q202: XP1501)
+3 regulator
(Q8: 2SB1132,
Q9: XP1501)
+3C regulator
(Q142: XP1501,
Q145: 2SB1132,
D143: MA2S111)
CPU3 regulator
(IC141: NJM2370U32)
440 MHz band modulation switch
(Q304: 2SJ364)
Microphone mute
(Q310: XP6501)
Microphone amplifier
(Q311: XP5601,
Q312: XP6501) 145 MHz band modulation switch
(Q305: 2SJ364)
50 MHz band modulation switch
(Q342: 2SJ364)
• LOGIC UNIT
Top view • LOGIC UNIT
Bottom view
S-13903MZ-C2
2002 Icom Inc.
1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Autres manuels pour IC-E90
2
Table des matières
Autres manuels Icom Émetteur-récepteur
Icom
Icom IC-V82 Manuel utilisateur
Icom
Icom IC-F3100D series Manuel utilisateur
Icom
Icom IC-2200H Manuel utilisateur
Icom
Icom IC-12E Manuel utilisateur
Icom
Icom IC-F5061/D Manuel utilisateur
Icom
Icom IC-M85UL Manuel utilisateur
Icom
Icom IC-7300 HF Plus Instructions d'installation
Icom
Icom IC-W21A Manuel utilisateur
Icom
Icom IC-M120 Manuel utilisateur
Icom
Icom IC-F11BR Manuel utilisateur
Icom
Icom IC-A23 Manuel utilisateur
Icom
Icom IC-229A Manuel utilisateur
Icom
Icom IC-9700 Guide de configuration
Icom
Icom IC-U220 Manuel utilisateur
Icom
Icom IC-703 Manuel utilisateur
Icom
Icom D-STAR ID-31A; D-STAR ID-31E Manuel utilisateur
Icom
Icom IC-F3GT Manuel utilisateur
Icom
Icom iM604A Manuel utilisateur
Icom
Icom IC-A2 Manuel utilisateur
Icom
Icom IC-A14 Manuel utilisateur
