IBM Flex System Fabric EN4093 Manuel utilisateur

Configuring the IBM Flex System Fabric EN4093 0Gb Scalable Switch

Prerequisites:

One IBM Flex System Enterprise Chassis and one IBM Flex System Fabric EN4093 0Gb Scalable

Switch installed in I/O module bay or 2.

An Ethernet network is already configured.

Steps:

Note: This process illustrates how to enable the switch ports through the Chassis Management Module

(CMM) command-line interface. For information about using the CMM interface, you can use the

“Configuring IBM Flex System Enterprise Chassis components” quick start guide. You can find that quick

start guide at this location:

In the information center (Internet):

http://pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.commontasks.doc/commonta

sks_chassis_config.html

The IBM Flex System product documentation is also available on the IBM Flex System Manager management node. To access

the installed documentation, click Information Center from the IBM Flex System Manager Home page and then navigate to:

IBM Flex System information -> Quick start guides -> Installing and configuring the IBM Flex System Enterprise Chassis

. Log on to the Chassis Management Module (CMM) CLI with an SSH application. The default IP

address is 92. 68.70. 00 and the default login/password is USERID/PASSW0RD. If necessary, obtain

the IP address and login of the CMM from your system administrator.

2. Set the environment to the bay where you installed the switch. Example for bay 2:

env -T system:switch[2]

3. Run the following command to enable external data ports:

ifconfig -ep enabled

External ports – 0 are now enabled for data throughput.

Page of 2

Activating additional keys:

If you have purchased additional keys, they need to be installed on the switch. Complete the following

steps to install additional keys using the ISCLI interface.

. To retrieve the key, navigate a browser to https://www.ibm.com/systems/x/fod/index.wss and

sign in with your ID and password.

2. Click Request activation key.

3. Enter the authorization code. The authorization code was supplied to you by email or on paper

as part of the ordering process.

4. Click Continue and follow the instructions and download the key file.

5. Log on to the EN4093 switch with an SSH application. The default IP addresses for the switch

through the CMM are as follows: 92. 68.70. 20 (bay ), 92. 68.70. 2 (bay 2),

92. 68.70. 22 (bay 3), 92. 68.70. 23 (bay 4). If necessary, obtain the IP address from your

system administrator.

6. Enter ena.

7. Enter software-key.

8. Enter enakey address <hostname or IP address> keyfile <file name>

protocol tftp mgt-port

Note: you must reset the switch to apply the key.

9. Reset the switch. Enter reload.

Repeat these steps for additional keys, if needed. The sequence of steps is shown here:

Router#ena

Router(config)#software-key

Router(Software-Key)#enakey address 9.44.143.206 keyfile

ibm_fod_0007_ 010CM28N001_anyos_noarch.key protocol tftp mgt-port

Starting download key file...

Key file download complete (494 bytes)

Software feature Upgrade1 will be Active upon next reboot.

Aug 5 11:47:39 1080:0:0:0:0:0:0:82 NOTICE mgmt: Software feature Upgrade1

will be Active upon next reboot.

A Reboot is required for the new settings to take effect.

Router(Software-Key)#reload

...

Resetting at 11:47:59 Tue Aug 5, 2014...

Page 2 of 2

Table des matières

Autres manuels IBM Changer

IBM

IBM 8285 Nways Manuel utilisateur

IBM

IBM BNT Manuel utilisateur

IBM

IBM Flex System EN2092 Manuel utilisateur

IBM

IBM 8239 Token-Ring Stackable Hub Guide de sécurité

IBM

IBM EN4093R Manuel utilisateur

IBM

IBM TotalStorage 3534-F08 Manuel utilisateur

IBM

IBM 17353LX - 1x8 Console Switch Manuel utilisateur

IBM

IBM SAN32M1 Manuel

IBM

IBM RackSwitch G8264T Manuel utilisateur

IBM

IBM RedBooks SAN24B-5 Manuel utilisateur

IBM

IBM Flex System EN2092 Manuel utilisateur

IBM

IBM Storage Networking SAN128B-6 Manuel

IBM

IBM J48E Manuel utilisateur

IBM

IBM SAN16B-2 - TotalStorage Express Model Switch Guide de dépannage

IBM

IBM G8124E Manuel utilisateur

IBM

IBM FC5022 Manuel utilisateur

IBM

IBM RackSwitch G8000 Manuel utilisateur

IBM

IBM TotalStorage 2109 M12 Manuel utilisateur

IBM

IBM 2498B24 - System Storage SAN24B-4 Switch Manuel

IBM

IBM 8270 Instructions d'installation et d'entretien

IBM

IBM TotalStorage 3534-F08 Manuel utilisateur

IBM

IBM 4002-Y2A Manuel utilisateur

IBM

IBM RedBooks SAN24B-5 Manuel

IBM

IBM 8265 Nways ATM Switch Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur