IBM Ultrastar 36XP Manuel utilisateur

IBM storage products

Installation guide

Ultrastar36XP

Multi-mode SE/LVD

DRHS-36V

DRHS-36D

Models:

Table of contents

Page 25

Glossary

............................................................

.....

Page 20

Appendix

................................................................

Page 19

Step 10: Operating system installation

.........................................

Page 18

Step 9: Formatting

.........................................................

Page 16

Step 8: FDISK

.............................................................

Page 13

Step 7: Installation and configuration

.........................................

Page 13

Step 6: Complete physical installation

.........................................

Page 12

Step 5: Connectors

........................................................

Page 11

Step 4: Mounting

..........................................................

Page 9

Step 3: Jumper Settings

.....................................................

Page 9

Step 2: Prepare for installation

................................................

Page 7

Step 1: Installation checklist

..................................................

Page 6

Hard disk drive installation flow chart

..........................................

Page 5

Hard disk drive handling guide

................................................

Page 4

Hardware description

........................................................

Page 3

Introduction

.........................................................

......

IBM storage products

Page 2

IBM Hard Disk Drive Technical Support Center version 1.0

Introduction

This manual was prepared to help you install your IBM Ultrastar 36XP hard drive in most computer

systems. If you do not feel comfortable installing this drive yourself, contact a qualified installer to assist

you.

International Business Machines Corporation provides this publication "AS IS" without warranty of any

kind, either express or implied, including, but not limited to, the implied warranties of merchantability or

fitness for a particular purpose. Some states do not allow disclaimers of express or implied warranties in

certain transactions. Therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Product data and

specifications are subject to change without notice. Changes are periodically made to the information

herein; these changes will be incorporated in new editions of the publication. IBM may make

improvements and/or changes in the product(s) and/or the program(s) described in this publication at any

time.

It is possible that this publication may contain reference to or information about IBM products (machines

and programs), programming, or services that are not announced in your country. Such references or

information must not be construed to mean that IBM intends to make available such IBM products,

programming, or services in your country.

Product description data contained herein represents IBM’s design objectives and is provided for

comparison among IBM products; actual results may vary based on a variety of factors. Except as

explicitly stated in the Warranty section of this Guide, the product data contained herein does not

constitute a warranty. Questions regarding IBM warranty terms or the methodology used to derive data

should be referred to an IBM representative.

Technical information about IBM hard disk drive products can be obtained via the Internet at:

http://www.ibm.com/harddrive or by calling the IBM Hard Disk Drive Technical Support Center at

888.426.5214.

Government Users - Documentation related to restricted rights - Use, duplication,or disclosure is subject

to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

IBM is a registered trademark of the International Business Machines Corporation. The following are also

trademarks or registered trademarks of the International Business Machines Corporation in the United

States, other countries, or both: Ultrastar and OS/2. Any other products or trademarks are the property

of their respective owners.

IBM storage products

Page 3

IBM Hard Disk Drive Technical Support Center version 1.0

Hardware description

The Ultrastar 36XP is available in various models with the following options:

{Capacity of 36GB

{68 pin or 80 pin (SCA) connectors

{68 pin SCSI connectors use the SCSI P connector which supports wide data transfers

{80 pin SCSI connectors use the SCA-2 connector

These drives offer an advanced LVD interface that supportstransfer rates of up to 80 MB/sec. To take

advantage of the higher transfer rate of 80 MB/sec, your computer will need to have a controller that

supports the LVD interface. If you have a SCSI controller that does not support this interface, the drive

will still function, but will be limited to data transfer speedssignificantly lower than 80MB/sec due to the

lower speed of your controller. If you have a slower controller, you may wish to purchase an LVD

controller card to take advantage of Ultrastar’s 80 MB/sec data transfer rate. An LVD controller card will

fit into any available slot in your computer.

If you currently have wide SCSI drives (single-ended) and a non-LVD controller, you may still attach the

LVD model Ultrastar 36XP to the existing cable. However, single-ended wide SCSI drives cannot be

added to the same bus as an LVD drive if that bus is connected to an LVD controller.

To determine if your current controller card is LVD, see the documentation that came with your controller

or contact the controller manufacturer for this information.

These drives are 3.5" drives designed to work in NT and Unix workstations and servers. They are ideal

for use by video producers and movie editors. The Ultrastar 36XP familyis designed to work with MMX

systems. Compatibility listings are included in the appendix. Before you begin installation, please read

the “Hard disk drive handling guide” on the following page.

IBM storage products

Page 4

IBM Hard Disk Drive Technical Support Center version 1.0

Low Voltage Differential (Ultra2)

80 SCA-2

DRHS-36V

36GB

Low Voltage Differential (Ultra2)

68 / Unitized Connector

DRHS-36V

36GB

SCSI Electrical Signal Type

SCSI Pins/Connector Type

Model

Capacity

Hard disk drive handling guide

These notes are designed to provide a simple overview of the need for cautiounwhen handling a disk

drive.

Disk drives can be easily damaged by electrical static shock or rough handling. In order to minimize the

risk of damage to a disk drive, it is essential that the drive be handled while resting on a cushioned

surface (which is electrostatically safe). Many such static safe mats are available, examples are 3M's

8210 table mat or 3M's "First Touch" computer pad.

Great care should be taken when handling disk drives. Do not bump them against any object. When

attaching brackets or mounting the drive in the computer, be very careful. It is very easy to

unintentionally introduce shocks which exceed specifications.

Please note that the capacity of each disk drive to withstand electrical or mechanical shock varies

according to its design. The IBM Hard Disk Drive Technical Support Center can advise you on the

suitability of your Ultrastar drive for a specific application.

Damage incurred to a drive might not be immediately evident and could cause the drive to fail long after

the damage occurred.

IBM storage products

Page 5

IBM Hard Disk Drive Technical Support Center version 1.0

Hard disk drive installation flow chart

IBM storage products

Page 6

IBM Hard Disk Drive Technical Support Center version 1.0

Step 1

Installation checklist/assemble

needed equipment

Page 7

Step 2

Prepare for installation

Page 9

Step 3

Jumper

settings

Page 9

Step 5

Connectors

Page 12

Step 4

Mounting the drive

Page 11

Step 6

Complete physical

installation

Page 13

Step 7

Installation and

configuration

Page 13

Step 8

FDISK

Page 16

Step 9

Formatting

Page 18

Step 10

Operating system installation

Page 19

Step 1: Installation checklist

To install the Ultrastar drive you may need the following items,depending on your computer’s

components:

1) __ The installation kit (as shown in the diagram below) containing the Ultrastar drive, 4 mounting

screws, and any related publications. Save the box the drive came in.

2) __ The documentation that came with your computer or storage enclosure.

3) __ A small, flat-blade screwdriver.

4) __ A SCSI controller, which is either built-in or an adapter inside your computer,and any related

documentation.

5) __ Mounting brackets, if required for your computer. Contact your place of purchase if you

are unsure if mounting brackets are required.

6) __ A bootable DOS diskette. (See the section entitled Making a bootable diskette in the

appendix.)

7) __ If you are replacing an older internal drive with the new Ultrastar drive and want to copy all of the

files from the older drive to the new drive, you may need additional software. (See the section

entitled Drive copy in the Appendix.)

Continue installation with the following procedures:

1) __ Backup your existing drive to avoid any loss of data during installation. (See the section entitled

Backup and restore in the Appendix.)After completing backup, shut down as normal.

2) __ Unplug your system from the electrical outlet.

3) __ Discharge static electricity by establishing a common voltage between your body and the hard

drive. Simultaneously touch an unpainted metal surface on the outside of your computer system

with your bare hands and the hard drive in its anti-static bag.Avoid excessive movement until the

drive has been mounted.

IBM storage products

Page 7

IBM Hard Disk Drive Technical Support Center version 1.0

Installation

Guide

Jumpers

Screws

Screwdriver

Installation Guide

Hard Drive

4) __ DO NOT LOW-LEVEL FORMAT YOUR DRIVE! IBM drives are low-level formatted by the

manufacturer and reformatting may cause permanent damage to your drive and your system. (See

the section entitled Utilities in the Appendix.)

5) __ Record the following information:

Drive Model ________________ Date of Purchase_________________

Drive P/N __________________ Place of Purchase_________________

Serial # ____________________

IBM storage products

Page 8

IBM Hard Disk Drive Technical Support Center version 1.0

Step 2: Prepare for installation

Opening your computer

1. Turn the system off.

2. Unplug the power cord from the wall outlet.

3. Remove all cables from the back of your computer, labeling them if necessary.

4. Remove the cover from your computer. (Consult your user's guide for instructions if needed.)

Unpackaging your hard drive

1. Remove the drive from the anti-static package that it was shipped in.

2. Handle the drive by the sides only.

3. Do not touch the main computer chip board.

4. Do not drop. A drop from only 1/4 inch could permanently damage your hard drive.

5. If available, use an ESD (Electronic Static Discharge) wrist strap while handling your drive.

6. Place the drive carefully on a static free area.

Step 3: Jumper settings

The jumper settings are found on the hard drive on the opposite end of the interface connector (see

diagram page 12). They are physical settings that must be changed for different uses of ahard drive.

SCSI ID Jumpers

Each SCSI device will need to have its own SCSI ID. You can use ID 0 through ID 15,reserving ID 7 for

your controller card. Follow the table below to set an ID on your SCSI drive.

off

Address

Bit 0

Bit 1

Bit 2

Bit 3

*Reserved for controller card

SCSI Address Determination

IBM storage products

Page 9

IBM Hard Disk Drive Technical Support Center version 1.0

Drive Termination

The SCSI bus will need to be terminated at both ends of the bus. The Ultrastar 36XP does not have

onboard active termination. You will need to supply an external Ultra2 compatible terminator.

Termination Power

Some controllers may require the drive to supply 5 volts of power to the bus to aid termination. If your

controller requires this, place a jumper on the Termination Power Enable jumpers to the side of the

jumper block. These pins require a 2.54mm jumper shunt.

Auxiliary Option Jumper Block

The 68 pin models contain an auxiliary connector that replicates some of the functions provided by the

front option jumper block. The auxiliary connector should only be used if you have a combination

“ganged” switch, typically found in external drive enclosures. The front option block and the auxiliary

option block may not be used simultaneously.

IBM storage products

Page 10

IBM Hard Disk Drive Technical Support Center version 1.0

: : : : : :

68 Pin Auxiliary Connector

12 10 8 6 4 2

11 9 7 5 3 1

+5V ID3ID2ID1

ID0

Write Protect

Ground

External Activity LED

Reserved

Auto Spin Start

Unused

SCSI Address

Autres manuels pour Ultrastar 36XP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IBM Stockage

IBM

IBM FlashSystem 9150 Manuel

IBM

IBM WDA L80 Manuel utilisateur

IBM

IBM Storwize V5000E Manuel utilisateur

IBM

IBM CISCO MDS 9124 - UPDATE FOR SYSTEM STORAGE Manuel technique

IBM

IBM DS8880 Series Manuel technique

IBM

IBM TS4500 Manuel technique

IBM

IBM Travelstar 3GN Manuel utilisateur

IBM

IBM Options 09N4153 Manuel utilisateur

IBM

IBM LC921 Manuel utilisateur

IBM

IBM Ultrastar 36XP Manuel utilisateur

IBM

IBM DCAS-32160 - Ultrastar 2.1 GB Hard Drive Manuel utilisateur

IBM

IBM System Storage DS5020 Guide d'installation

IBM

IBM TotalStorage DS4800 Mode d'emploi

IBM

IBM Ultrastar 18XP Manuel utilisateur

IBM

IBM System storage DS6000 Series Manuel utilisateur

IBM

IBM 39M5657 Manuel utilisateur

IBM

IBM Slicestor 3448 Manuel utilisateur

IBM

IBM 160 GB DLTV4 Manuel utilisateur

IBM

IBM Slicestor 2212A Manuel utilisateur

IBM

IBM DS8000 - ADDITIONAL INFORMATION Manuel utilisateur

IBM

IBM System Storage N3220 Manuel

IBM

IBM 4146 T30 Manuel utilisateur

IBM

IBM SYSTEM STORAGE EXP3000 - INTEROPERABILITY MATRIX... Manuel utilisateur

IBM

IBM TS3400 Guide de configuration

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur