IBM DS3500 Manuel utilisateur
System Storage DS3500 and EXP3500 Rack Installation and
Quick Start Guide
This Rack Installation and Quick Start Guide describes the basic procedure for installing the IBM®System
Storage®DS3500 storage subsystem and the IBM System Storage EXP3500 storage enclosure. The
information in this document pertains to the DS3512 and DS3524 storage subsystems, and the EXP3512
and EXP3524 storage enclosures.
For information about cabling and configuring the DS3500 storage subsystem and the EXP3500 storage
enclosure, see the IBM System Storage DS3500 and EXP3500 Installation, User's, and Maintenance Guide that
came with the hardware.
For educational information about the DS3500 and other IBM System Storage products, go to
http://ibmdsseriestraining.com/.
For the latest information about IBM System Storage disk storage systems, including all of the DS3000
storage subsystems and storage enclosures, go to http://www.ibm.com/systems/support/storage/disk.
For safety information, see the multilingual IBM Safety Information document on the Documentation CD.
Rack installation guidelines
Review the documentation that came with your rack cabinet for safety and cabling information. Before
you install the storage subsystem in a rack cabinet, review the following guidelines:
vTwo or more people are required to install devices 18 kg (39.7 lb) or heavier in a rack cabinet.
vMake sure that the room air temperature is below 35°C (95°F).
vDo not block any air vents; usually 15 cm (6 in.) of space provides proper airflow.
vDo not leave open spaces above or below an installed storage subsystem in your rack cabinet. To help
prevent damage to storage subsystem components, always install a blank filler panel to cover the open
space and to help ensure proper air circulation.
vInstall the storage subsystem or expansion enclosure only in a rack cabinet with perforated doors.
vPlan the device installation starting from the bottom of the rack cabinet.
vInstall the heaviest device in the bottom of the rack cabinet.
vDo not extend more than one device out of the rack cabinet at the same time.
vRemove the rack doors and side panels to provide easier access during installation.
vConnect the storage subsystem or expansion enclosure to a properly grounded outlet.
vDo not overload the power outlet when you install multiple devices in the rack cabinet.
vThe storage subsystem or expansion enclosure requires2Uofvertical space in the rack cabinet.
Use safe practices when lifting.
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
Inventory list
The following inventory list describes the items that you need to install the DS3500 storage subsystem or
EXP3500 storage enclosure in the rack cabinet. If any items are missing or damaged, contact your place of
purchase.
Notes:
1. Depending on your DS3500 or EXP3500 order, your shipping box might contain additional materials
not listed in the following checklist. Review the inventory checklist in the IBM System Storage DS3500
and EXP3500 Installation, User's, and Maintenance Guide that came with the hardware for any additional
parts, and use that checklist in combination with the following information.
2. The host-interface cables, Ethernet cables, Fibre Channel signal cables, and iSCSI signal cables that are
shipped vary with the hardware, and not included in the following list.
After you unpack the DS3500 or EXP3500, verify that you have the following items for each storage
subsystem or storage expansion controller.
vHard disk drives or blank trays (12 or 24) (Your storage subsystem or expansion enclosure might come
with up to 24 drives.)
vRAID controllers (DS3500 only, up to 2)
vEnvironmental Service Modules (ESM) (EXP3500 only, 1)
vAC power models:
– AC power supply and fan units (2)
– Rack jumper line cords (2)
vDC power models:
– DC power supply and fan units (2)
– DC jumper cables (2)
vRack-mounting hardware kit (1), including:
– Support rails (2) (right and left assembly)
– M5 black hex-head slotted screws (8)
– M5 washers (6)
– Small diameter spacers (8) (these come installed, four in each rail)
– Large diameter spacers (8)
– M4 pan-head screws (2)
Important: The DS3500 and EXP3500 ac power models do not ship with region-specific ac power cords.
You must obtain the IBM-approved power cords for your region. The DS3500 and EXP3500 dc
power models do not ship with a 30A rated disconnect device (circuit-breaker) that is
required for the -48V DC power connection. See the IBM System Storage DS3500 and EXP3500
Installation, User's, and Maintenance Guide for more information.
Tools
Before you install the DS3500 or EXP3500, the installation area must have an Internet connection, and you
must have the following tools:
vA cart to hold the storage subsystem and its components
vA 5 mm (3/16-in.) flat-blade screwdriver
vAnti-static protection
Note: A No. 2 Phillips screwdriver and an 8 mm wrench are optional.
2
Installation overview
The installation of the DS3500 or EXP3500 involves the following procedures:
1. “Unpacking the storage subsystem”
2. “Installing the support rails” on page 4
3. “Removing the storage subsystem or expansion enclosure components” on page 5
4. “Installing the storage subsystem or storage enclosure in the rack cabinet” on page 9
5. “Turning on the power - AC models” on page 11
6. “Installing the software” on page 14
7. “Discovering and setting up the storage subsystem” on page 15
8. “Obtaining information from the IBM Support Web site” on page 16
9. “Updating the storage subsystem firmware” on page 16
10. “Configuring the storage subsystem” on page 16
Unpacking the storage subsystem
Statement 4:
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
To unpack the storage subsystem or expansion enclosure, complete the following steps:
1. With the help of one other person, remove the storage subsystem or expansion enclosure from the
shipping box and place it on a cart, table, or other raised surface.
2. Check the storage subsystem or expansion enclosure to make sure that you received all the necessary
parts. See the “Inventory list” on page 2 section for the parts that are included with the storage
subsystem or expansion enclosure.
3. Take the left and right support rails and the M5 screws and proceed to “Installing the support rails”
on page 4.
3
Installing the support rails
Notes:
1. For proper weight distribution, install the support rails from the storage subsystem ship group in the
lower portion of the rack cabinet.
2. If you are installing a storage subsystem, make sure that you allow for room above and below the
storage subsystem for storage enclosures.
3. The support rails are marked “R” and “L” for right and left.
To install the left and right support rails in the rack cabinet, complete the following steps.
1. Starting with the left support rail, loosen the two rail adjustment screws. The adjustment screws are
used to lock the support rails at a certain length.
2. Hold the front of the left support rail against the inside of the front rack cabinet support flange, and
extend the rear of the support rail until it makes contact with the rear rack cabinet support flange.
The alignment spacers at the rear of the support rail slide into the holes at the rear of the rack cabinet,
as shown in Figure 2.
Note: If the rack has square holes, replace the small spacers on the front and rear of the rails with the
larger spacers that came with the rail kit.
3. From the front of the rack cabinet, with the support-rail flanges positioned inside the rack cabinet
support rail assemblies, tighten one M5 screw in the second hole from the top of the rail bracket with
a screwdriver, as shown in Figure 3 on page 5.
Rail-adjustment screws
Figure 1. Rail-adjustment screws
Alignment spacers
Figure 2. Positioning the support rails in the rack
4
Note: Make sure that you use a washer when you install an M5 screw through a square hole on a
rack-mounting flange.
4. From the rear of the rack cabinet, tighten two M5 screws in the bottom hole and the hole second from
the top of the rear rail bracket with a screwdriver.
Note: Make sure that you use a washer when you install an M5 screw through a square hole on a
rack-mounting flange.
5. Repeat steps 2 on page 4 through 4 for the right support rail.
Removing the storage subsystem or expansion enclosure components
Remove the controllers or ESMs, hot-swap drives, and the power supply and fan units before you lift the
storage subsystem or expansion enclosure. This reduces the weight of the DS3500 or EXP3500 during
installation. Each component in the back of the DS3500 and EXP3500 is held in place by a lever that has a
locking latch.
To remove the components, complete the following steps.
Note: The DS3500 storage subsystem and the EXP3500 expansion enclosure use the same power supply,
so the same removal procedure applies to both.
M5 screw (1)
M5 screws (2)
Figure 3. Securing the support rails in the rack
5
1. Remove the power supplies:
a. Press the release tabs and open the release levers as shown in the illustration. The power supply
moves out of the bay approximately 0.6 cm (0.25 inch).
b. Slide the power supply out of the bay and set it aside.
2. If you have an EXP3512 or EXP3524 expansion enclosure, remove the ESMs:
a. Open the two release levers. The ESM moves out of the bay approximately 0.6 cm (0.25 inch).
b. Slide the ESM out of the bay and set it aside.
Power supply
Release
levers
Figure 4. Removing a power supply from a DS3500 storage subsystem or an EXP3500 expansion enclosure
Release
levers
ESM
12
ESM
Figure 5. Removing an ESM from an EXP3512 or EXP3524
6
3. If you have a DS3512 or DS3524 storage subsystem, remove the controller or controllers:
a. Open the two release levers as shown in the illustration. The controller moves out of the bay
approximately 0.6 cm (0.25 inch).
b. Slide the controller out of the bay and set it aside.
Release
levers
Figure 6. Removing a controller from a DS3512 or DS3524
Drive tray
Tray handle
Latch
Hard disk drive
System Storage
Figure 7. Removing a hard disk drive from a DS3512 or an EXP3512
7
4. Remove the drives:
a. Label the drives so that you can replace them in their original order.
b. Release the latch on the drive by pressing on the inside of the bottom of the tray handle.
c. Lift the closed latch to its open position. When the latch is open, it is at a 90° angle to the front of
the drive.
d. Pull the drive out of its bay.
e. Repeat steps 4b through 4d for each drive.
5. See the IBM Systems Storage DS3500 and EXP3500 Installation, User's, and Maintenance Guide that came
with the enclosures for more information about removing the components.
Drive tray
Tray handle
Latch Hard disk drive
Figure 8. Removing a hard disk drive from a DS3524 or EXP3524
8
Installing the storage subsystem or storage enclosure in the rack
cabinet
To install the storage subsystem, complete the following steps:
1. Read the safety information that comes with the storage subsystem or storage enclosure.
2. Slide the rear of the storage subsystem or expansion enclosure onto the support rails as shown for the
DS3512 and EXP3512 in Figure 9, and for the DS3524 and EXP3524 in Figure 10.
Note: The DS3524 and EXP3524 do not use the support rail alignment tabs.
Alignment tab
(both sides)
Figure 9. Positioning a DS3512 or EXP3512 in a rack
Figure 10. Positioning a DS3524 or EXP3524 in a rack
9
3. Align the front mounting holes on each side of the storage subsystem or expansion enclosure with the
mounting holes on the front of the support rails.
4. Install and tighten one M5 screw in the support hole on each side of the front of the storage
subsystem or expansion enclosure (no washer is required), as shown for the DS3512 or EXP3512 in
Figure 11, and for the DS3524 or EXP3524 in Figure 12.
5. Install and tighten the two M4 screws through rear of the support rails into the slotted holes on the
outside of the storage subsystem or expansion enclosure.
M5 screws
Figure 11. Securing a DS3512 or EXP3512 to a rack
Autres manuels pour DS3500
5
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels IBM Stockage
IBM
IBM 01K1316 Manuel du propriétaire
IBM
IBM DCAS-32160 - Ultrastar 2.1 GB Hard Drive Manuel utilisateur
IBM
IBM IC35L036UWDY10 - Ultrastar 36.7 GB Hard... Manuel utilisateur
IBM
IBM Deskstar 16GP Manuel utilisateur
IBM
IBM Deskstar 16GP Manuel utilisateur
IBM
IBM FlashSystem 840 Manuel utilisateur
IBM
IBM TotalStorage IP Storage 200i 110 Manuel utilisateur
IBM
IBM SAN Volume Controller Manuel du propriétaire
IBM
IBM totalstorage 200 Manuel utilisateur
IBM
IBM 5280 Manuel utilisateur
IBM
IBM Computer Drive Manuel utilisateur
IBM
IBM DS4700 EXPRESS Manuel utilisateur
IBM
IBM Netfinity EXP300 Manuel du propriétaire
IBM
IBM DS3500 Mode d'emploi
IBM
IBM 200 GB LTO-2 Manuel utilisateur
IBM
IBM CD-RW/DVD-ROM Combo Drive Manuel utilisateur
IBM
IBM XIV STORAGE SYSTEM Manuel utilisateur
IBM
IBM FlashSystem 820 Manuel utilisateur
IBM
IBM Travelstar 14GS Manuel utilisateur
IBM
IBM SAN192C-6 Manuel
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur